2008 GEELY FC torque

Wiper and cleaner--Wiper generator
8. Disassemble wiper generator
(a) Separate two connecting rod caps of shaft pins.
(b) Separate two star- bolts so as to disassemble wiper
generator.
9. Assemble wiper generator
(a) Daub MP grease to connecting rod caps of wiper generator.
(b) Use two Star-bolts to assemble wiper generator to wiper
connecting rod.
Torque: 5.39 N.m
10. Assemble wiper connecting rod assembly
[68000053]
(a) Meshing wiper connecting rod rubber pin
(b) Use two bolts to assemble wiper connecting rod.
Torque:5.5 N.m
(c) Connect the joints.
11. Assemble assistant wiper arm assembly [68000059]
(a) Use steel brush to clean small tooth slot of wiper pivot.
(b) Use bolt cap to fix wiper arm on passenger side to make
wiper blade at the position as drawing.
Torque: 20.5 N.m
12. Assemble main wiper arm assembly [68000057]
(a) Use steel brush to clean small tooth slot of wiper pivot.
(b) Use bolt cap to fix wiper arm on driver side to make wiper
vane at the position as drawing.
Assembly starting and
stopping position
 304 
Assembly starting and
stopping position

Chair--Front chair
Chair
Front chair
Subassembly
 348 
N.
m: Regulated torque
Head pillow assembly
Head pillow bracket
Chair backrest
gasket
Chair backrest
bracket
Exterior cover of
chair backrest
Exterior cover of
chair gasket
Inner trim cover of
front chair gasketWith waist support:
Adjusting lever of
waist support lever
Rear cover of chair
sliding rail With waist support:
Waist support
adjustment assembly
Declining adjust-
ment releasing
handle
Chair gasket bracket
auxiliary assemblyFront cover of chair
sliding rail
Chair vertical
adjusting button
Lower trim cover of
front chair gasket Exterior trim cover
of front chair
gasket Chair
gasket
Chair front and rear
adjusting handle
Inner safety belt
clamp of front chairClamp
Clamp

5. Disassemble lower trim cover of front chair gasket.
6. Disassemble inner trim cover of front chair gasket.
Disassemble the screw and inner trim cover of front chair gasket.
7. Disassemble left front safety belt locker assembly
[68010040]
(a) Cut off fixing clasp.
(b) Disassemble the bolt and left/right front safety belt locker
Chair--Front chair
 350 
assembly.
8. Disassemble chair backrest assembly.
(a) Disassemble the clasp.
(b) Over turn exterior cover of chair backrest , then disassemble the clasp.
(c) Disassemble four bolts and chair backrest assembly.
9. Disassemble exterior cover of chair backrest .
(a) Disassemble head pillow bracket.
(b) Disassemble fixing clamp and adjusting lever of waist support lever.
(c) Disassemble the clamp, then disassemble exterior cover of chair backrest with gasket.
(d) Disassemble the clamp, then disconnect exterior cover of chair backrest with chair backrest gasket.
(e) Disassemble two screws and waist support lever.
10. Disassemble exterior cover of chair gasket.
(a) Disassemble fixing clamp, then disassemble exterior cover of chair backrest with gasket.
(b) Disassemble the clamp, then disconnect exterior cover of chair backrest with chair backrest gasket.
11. Disassemble chair gasket bracket assembly.
12. Disassemble chair front and rear adjusting handle.
Use screw driver to disassemble chair front and rear adjusting handle.
Hint: before using screw driver, it is necessary to wrap its needled top with adhesive tape.
13. Assemble chair gasket bracket assembly.
Use four bolts to assemble chair gasket bracket on chair adjustment assembly.
Torque: 20 N
⋅ ⋅⋅ ⋅
⋅m
14. Assemble exterior cover of chair gasket.
(a) Use new clamp to assemble exterior cover of chair gasket in chair gasket.

(b) Use new clamp to assemble chair gasket on chair gasket
bracket.
Hint:
zDo not damage or dirty exterior cover of chair
gasket.
zWhen assembling clamp, it is necessary to prevent
exterior cover of chair gasket from crinkling.
15. Assemble exterior cover of chair backrest .
(a) Use new clamp to assemble exterior cover of chair backrest
in chair gasket.
(b) Use new clamp to assemble chair backrest on chair
backrest bracket.
Hint:
zDo not damage or dirty exterior cover of chair
backrest .
zWhen assembling clamp, it is necessary to prevent
Chair--Front chair
Locking loop pliers
Locking loop pliers
 351 
exterior cover of chair backrest from crinkling.
16. Assemble chair backrest assembly.
(a) Use four bolts to assemble chair backrest assembly.
Torque: 45 N
⋅ ⋅⋅ ⋅
⋅m
(b) Over turn exterior cover of chair backrest to assemble clamp.
(c) Assemble the clamp.
17. Assemble left front safety belt locking assembly [68010040]
(a) Use the bolt to assemble left front safety belt locking assembly.
Torque: 42 N
⋅ ⋅⋅ ⋅
⋅m
(b) Assemble fixing clasp.
18. Assemble driver chair assembly.
(a) Assemble driver chair.
Note: do not damage automobile body.
(b) Connect the joint.
(c) Assemble four bolts.
Torque: 47 N
⋅ ⋅⋅ ⋅
⋅m
(d) Assemble right front lower trim board, right rear lower trim board and left lower trim board of driver chair.

Chair--Rear chair (separating type)
(f) Disassemble the clamp, then disconnect exterior cover of
rear row backrest with gasket.
10. Disassemble exterior cover of rear row chair
cushion.
Disassemble the clamp, then disconnect exterior cover of cush-
ion with gasket.
11. Assemble exterior cover of rear row chair cushion.
Use new clamp to assemble exterior cover of rear row chair
Locking loop pliers
 353 
cushion in gasket.
Hint:
zDo not damage or dirty exterior cover of cushion.
zWhen assembling clamp, it is necessary to prevent exterior cover of cushion from crinkling.
12. Assemble exterior cover of rear row chair backrest (big).
Hint:
zDo not damage or dirty exterior cover of cushion.
zWhen assembling clamp, it is necessary to prevent exterior cover of cushion from crinkling.
13. Assemble exterior cover of rear row chair backrest (small).
Use new clamp to assemble exterior cover of rear row chair backrest in gasket.
Hint:
zDo not damage or dirty exterior cover of cushion.
zWhen assembling clamp, it is necessary to prevent exterior cover of cushion from crinkling.
14.Assemble rear backrest central hinge assembly.
Use two bolts to assemble central hinge assembly.
Torque: 20 N
⋅ ⋅⋅ ⋅
⋅m
15. Assemble rear chair backrest side hinge assembly.
Use two bolts to assemble two side hinge assemblies.
16. Assemble rear row chair left backrest assembly [68010078]
Use the bolt to assemble left backrest assembly.
Torque: 8.0 N
⋅ ⋅⋅ ⋅
⋅m
17. Assemble rear row chair right backrest assembly [68010079]
Use the bolt to assemble right backrest assembly.
Torque: 8.0 N
⋅ ⋅⋅ ⋅
⋅m
18. Assemble rear row chair backrest assembly.
Use four bolts to assemble backrest assembly.
Torque: 18 N
⋅ ⋅⋅ ⋅
⋅m

Rear chair (fixing type)
Overhaul
Hint: When assembling, please work by the sequence
opposite with disassembling sequence, but when it has
items that need to pay special attention, it will add special
specification.
1. Disassemble rear row chair cushion assembly.
Pull rear row chair cushion assembly upwards, then disas-
semble it.
Note: when disassembling, it is necessary to hold the
bracket at two sides of fixing clasp, then pull it upwards
to prevent it from distorting.
2. Disassemble rear row chair backrest assembly
[68010076]
Disassemble three bolts and rear row chair backrest assembly.
3. Disassemble rear chair head pillow assembly
[68010077]
4. Disassemble exterior cover of rear row chair
backrest.
(a) Disassemble head pillow bracket.
(b) Disassemble the clamp, then disconnect exterior cover of
rear row chair backrest with gasket.
5. Disassemble exterior cover of rear row chair cushion.
Disassemble the clamp, then disconnect exterior cover of cush-
ion with gasket.
6. Assemble exterior cover of rear row chair cushion.
Use new clamp to assemble exterior cover of rear row chair
cushion in gasket.
Hint: Do not damage or dirty exterior cover of cushion.
When assembling clamp, it is necessary to prevent exterior
cover of cushion from crinkling.
7. Assemble exterior cover of rear row chair backrest.
Use new clamp to assemble exterior cover of rear row chair
backrest in gasket.
Hint: Do not damage or dirty exterior cover of cushion.
When assembling clamp, it is necessary to prevent exterior
cover of cushion from crinkling.
8. Assemble rear row chair backrest assembly
[68010076]
Torque: 8.0 N·m
Chair--Rear chair (fixing type)
Locking loop pliers
Locking loop pliers
A:100mm
 354 

Electric sunroof (optional)--Sunroof
7. Use screw driver (twisted by adhesive tape) to align
the sunroof driving pull cable with right mark.
8. Assemble sunroof shell body assembly.
(a) Bolt.
Torque: 5.5 N
⋅ ⋅⋅ ⋅
⋅m
(b) Screw cap.
Torque: 5.0 N
⋅ ⋅⋅ ⋅
⋅m
9. Assemble the glass of sunroof.
(a) Check the phase difference between sunroof waterproof ad-
hesive tape and top gasket.
Front end and rear end: 0±1.5mm
Rear corner: 0±1.5mm
0-1.5mm
(b) Adjustment
Use T25 planetary wrench to loosen the screw to adjust
the sunroof on correct position, then lock the screw.
10. Inspection for water leakage.
(a) After the adjustment, check whether the sunroof leaks water.
(b) If sunroof leaks water, adjust it again.
Assembly mark
 363 

Engine cover/automobile door
Engine cover
Adjustment
Engine cover/automobile door--Engine cover
 366  1. Check engine cover assembly.
Check whether the clearance of engine cover is in regulated
value shown in table.
2. Adjust engine cover assembly.
(a) Adjust engine cover assembly by loosening the hinge bolt at
the side of engine cover.
Torque: 13 N
⋅ ⋅⋅ ⋅
⋅m
(b) Adjust engine cover assembly by turning the gasket.
(c) Adjust engine cover assembly by loosening three bolts of
engine cover locker.
Torque: 7.0 N
⋅ ⋅⋅ ⋅
⋅m