2008 GEELY FC engine

Hydraulic control unit (equipping with ABS)Inspection on automobile1. Connect handle tester(a) Connect handle tester to DLC3.
(b) Start the engine and make it run at idling speed.
(c) Handle tester should choose “Active test” module.
Hint: details could refer to operating instruction for handle tester.2. Check the function of hydraulic .(a) Start the motor relay, and check hydraulic motor should have working sound.
(b) Stop the motor relay.
(c) Step brake pedal for 15 minutes, and check brake pedal should not be stepped down.
(d) Start the motor relay, and check brake pedal should not have any pulse.
Note: Time when motor relay locates ON could not exceed 5 seconds, when it is necessary to
operate continually, interval time should be over 20 seconds.
(e) Stop the motor relay and release brake pedal.3. Check the function of right front wheel.Note: forbid making electromagnetic valve be ON in following situations.
(a) Make following operation when brake pedal is stepped down.
(b) Make electromagnetic valve SFRH and SFRR be ON at the same time, and check the brake pedal
should not be stepped down.
Note: Time when motor relay locates ON could not exceed 5 seconds, when it is necessary to
operate continually, interval time should be over 20 seconds.
(c) Make electromagnetic valve SFRH and SFRR be OFF at the same time, and check the brake pedal
should be able to be stepped down.
(d) Make electromagnetic valve SFRH and SFRR be ON at the same time, and check whether the brake
pedal could return.
Note: Time when motor relay locates ON could not exceed 5 seconds, when it is necessary to
operate continually, interval time should be over 20 seconds.
(e) Make motor relay be OFF and release brake pedal.4. Check the function of other wheels.Check the electromagnetic valves of other wheels by same procedure.
Hint:
Left front wheel: SFLH,SFLR
Right rear wheel: SRRH,SRRR
Left rear wheel: SRLH, SRLRChange1. Discharge brake liquid.Note: do not leave brake liquid on paint surface of automobile body, if having, wash it cleanly.2. Disassemble right front wheel.Brake--Hydraulic pressure control unit148

Power steering--Poser steering system
Inspection on automobile
1. Check driving belt
(a) Check whether the belt has been abraded too much with eyes, and rope is broken.
If finding any defect, change the driving belt.
Hint: Some light crack at the side of belt rib could be approved, but if belt has any crack from
its rib, it is necessary to change.
2. Exhaust air of power steering system
(a) Check the oil level.
(b) Lift up automobile body, and support it with bracket.
(c) Turn steering wheel.
(1) Turn steering wheel slowly from left and right to bottom for several times when engine extinguishes.
(d) Lay down the automobile.
(e) Start the engine to make it run at idling speed for several minutes.
(f) Rotate steering wheel.
(1) Keep engine at idling speed, and turn the steering wheel from left or right to bottom and keep this
state for 2-3 seconds, then turn it to the other direction for 2-3 seconds.
(2) Repeat (1) for several times.
(g) Engine extinguishes.
(h) Check whether there is any foam or emulsification
phenomenon.
If there is any foam or emulsification phenomenon and
it is necessary to exhaust air second time, it is necessary
to check whether the system has any leakage.
(i) Check the oil level.
3. Check the oil level
(a) Keep automobile horizontal.
(b) Extinguish the engine, and check the oil level of oil stor-
age tank.
If oil level is too low, add oil.
Power steering oil: automatic transmission oil
DEXRON’’ II or III
Hint: check whether the oil level is in the HOT mark
scope of oil storage tank, if oil is cool, check the
oil level is in COLD mark scope.
(c) Start the engine, and keep it at idling speed.
(d) Turn steering wheel from left bottom to right bottom for
several times to make oil temperature increase.
Oil temperature: 80°C
Normal Abnormal
 200 
Normal Abnormal

(e) If there is any foam or emulsification phenomenon, it is necessary to exhaust air in power steering
system.
(f) Keep the engine at idling speed, and measure the oil
level of oil storage tank.
(g) Engine extinguishes.
(h) After waiting for several minutes, measure the oil level
of oil storage tank again.
Maximal increased height of oil level: 5mm
If finding any problem, it is necessary to exhaust
the air in power steering system.
(i) Check the oil level.
4. Check steering oil pressure.
(a) Disassemble oil pressure supply pipe from power steering gear. (referring to page 205)
(b) Connect special tool liking that shown in figure.
Note: when checking, the valve of special tool should be opened.
(c) Exhaust the air in power steering system.
(d) Start the engine, and keep it at idling speed.
(e) Turn steering wheel from left bottom to right bottom for several times to make oil temperature
Power steering--Poser steering system
increase.
Oil temperature: 80°C
(f) Keep the engine at idling speed, and close the valve of
special tool, then observe the reading of special tool.
Minimal oil pressure: 6400kPa
Note:
yThe closing time of oil pressure meter valve could not
Accessory
Power steering
gear
InOut
Accessory Oil pressure supply pipe
Power
steering
gearClose
Pump Oil tank
Special tool
¡Ü¡Ü
¡Ü¡Ü¡Ü5mm
Special tool
 201 

Power steering--Power steering system
exceed 10 seconds.
yDo not make oil temperature become too high.
(g) When engine is running at idling speed, open the valve
completely.
(h) Measure the 1.000 rpm and 3.000 rpm oil pressure of
engine.
Oil pressure difference: 490 kPa or less
Note: do not turn the steering wheel.
(i) When engine is running at idling speed, open the valve
completely, and turn the steering wheel to bottom.
Minimal oil pressure: 6,400kPa
Note:
yDo not keep the wheel locate at bottom for over 10
seconds.
yDo not make oil temperature become too high.
(j) Disassemble the special tool.
(k) Connect oil pressure supply pipe with power steering gear
(referring to page 205)
(l) Exhaust the air in power steering system.
5. Check the steering force
(a) Put the steering wheel at central position.
(b) Disassemble safety airbag assembly at the side of driver.
(c) Start engine, and make it run at idling speed.
(d) Measure the steering force of two directions.
Steering force (reference): 5.5 N
x xx x
xm
Hint:before diagnosing, it is necessary to consider
the tyre type, tyre pressure and contacting sur-
face at first.
(e) Tighten fixed screw cap of steering wheel.
Torque: 50 ± 5 N
x xx x
xm
(f) Assemble the safety airbag assembly at the side of driver.
Power
steer-
ing
gearOpen
Pump Oil tank
Open
Pump Oil tank
Power
steering
gear
Turn the steering wheel
to the bottom position
Special tool
Special tool
 202 

10. Connect the in-out oil pipe assembly of power
steering gear [64000131]
(a) Assemble fixed clamp of in-out oil pipe with bolt.
Torque: 7.8 N
xm
(b) Connect in-out oil pipe with special tool.
Torque: 41 Nz
xm
Hint:
zUse torque wrench whose lever length is 345 mm.
zSpecial tool should be parallel with torque wrench,
only this could make practical torque value.
11. Connect the N0. 1 oil pipe of oil storage tank to power steering oil pump assembly.
Connect oil pipe with fixed clamp.
12. Assemble driving belt.
13. Assemble front wheel.
Torque: 103 ± 10 Nx xx x
xm
14. Add power steering oil.
15. Exhaust the air in power steering system.
16. Check whether there is any oil leakage.
17. Assemble right bottom defender board of engine [68000004].
Power steering--Power steering oil pump assembly
Special
tool
¸Ü¸Ü
¸Ü¸Ü¸Ü¸Ë¸Ë
¸Ë¸Ë¸Ë³¤³¤
³¤³¤³¤¶È¶È
¶È¶È¶È
 204 

Power steering--Power steering gear assembly
(b) Disassemble the screw and disconnect the fixed clamp of
in-out oil pipe assembly of power steering gear.
12. Disassemble linking lever assembly of front stabi-
lizer bar [64000097].
(a) Use socket head wrench (5mm) to fix bolt, then disas-
semble screw cap.
(b) Disassemble the left linking lever of front stabilizer liking
lever assembly.
Hint: disassemble the other with same method.
13. Disassemble the coupling bolt and nut of left/right
lower control arm ball head and control arm.
Disassemble one bolt and two nuts, and disassemble control
arm from left steering knuckle.
Hint: disassemble the other with same method.
14. Disassemble engine cover assembly
15. Support engine assembly.
16. Disassemble auxiliary automobile bracket assem-
bly [64000087]
(a) Disassemble two bolts, then disassemble side rail from
right front engine suspension.
(b) Disassemble two bolts, then disassemble carling from au-
tomobile body.
(c) Disassemble the bolt and three nuts, then disassemble
engine rear suspension from auxiliary automobile bracket.
(d) Use gearbox jack to support auxiliary automobile bracket.
(e) Disassemble four bolts and auxiliary automobile bracket
assembly with steering gear.
17. Disassemble exterior dust-proof cover of steering
column.
 206 

Power steering--Power steering gear assembly
34. Assemble steering middle shaft.
(a) Align the mark of steering middle shaft and steering small
gear shaft.
(b) Assemble the bolt.
Torque: 35 N
x xx x
xm
35. Assemble exterior dustproof cover of steering
column.
36. Assemble auxiliary bracket assembly (64000087).
(a) Use special tool to align the right side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt
temporarily.
(b) Use special tool to align the left side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt
temporarily.
(c) Use special tool to align the left side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt.
Torque:
A bolt: 157 ± 10 N
x xx x
xm
B bolt: 113 ± 10 N
x xx x
xm
(d) Use special tool to align the right side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt.
Torque:
A bolt: 157 ± 10 N
x xx x
xm
B bolt: 113 ± 10 N
x xx x
xm
(e) After connecting with engine with one bolt and three screw
caps, hang it to auxiliary bracket.
Torque: 52 N.m ± 5 N
x xx x
xm
(f) Assemble carling to body with two bolts.
Torque: 39 ± 3 N
x xx x
xm
(g) Assemble the front suspension of engine to carling with
two screw caps.
Torque: 52 ± 5 N
x xx x
xm
Align the mark
Special
tool
Special tool
 210 

Power steering--Power steering gear assembly
41. Connect the ball head at the right side of transver
sal lever .
42. Assemble right bottom defending board of engine
[68000004].
43. Assemble left bottom defending board of engine
[68000003].
44. Assemble front wheel
Torque: 103 ± 10 Nx xx x
xm
45. Connect steering slide shaft assembly.
(a) Align the mark between steering middle shaft and sliding
shaft.
(b) Assemble B bolt.
Torque: 35 ± 3 N
x xx x
xm
(c) Tighten the A bolt.
Torque: 35 ± 3 Nx xx x
xm
46. Assemble inner dustproof cover of steering column [64000123].
Assemble inner dustproof cover of steering column with two screw caps.
47. Make front wheel face the front
Hint: lift up front wheel shaft.
48. Assemble helix cable assembly (equipping with SRS).
49. Assemble steering wheel assembly [67010001].
(a) Align the mark between steering wheel and main shaft of steering column.
(b) Lock the fixed screw cap of steering wheel temporarily.
50. Add power steering oil (referring to page 200).
51. Exhaust the air in power steering system (referring to page 200).
52. Check the central point of steering wheel.
(a) Check the central point of steering wheel.
(b) Lock the fixed screw cap of steering wheel.
Torque: 50 ± N
x xx x
xm
53. Assemble safety airbag assembly at the side of driver (equipping with SRS) [67010011].
54. Check whether there is oil leakage.
55. Check the engine cover assembly.
56. Adjust the engine cover assembly.
57. Check and adjust the front wheel alignment (referring to page 87).
 212