2008 GEELY CK clock

216IV. FRONT FOG LAMP BEAM ADJUSTMENT1. Adjust the tire inflation pressure with the standard value
2. Start the engine
3. Turn the fog lamp switch ON
4. Adjust the fog lamp beam.
Turn the bolt A for adjusting fog lamp beam in vertical direction.
NOTES:
Turn the screwdriver counter-clockwise to make the light beam up, clockwise make the light beam down.

218II. INSTALLATION1. Install the rear combination lamp and then the 3 mounting bolts.
2. Install the electrical connector.
3. Install the rear trunk interior trim.
4. Install the seal strip.III. REAR COMBINATION LAMP BULB REPLACEMENT1. Remove the O-ring seal.
2. Turn the lamp-holder counter-clockwise. Pull out the lamp-holder.
3. Remove the bulb and replace the bulb.Section 6 High Mounted Stop Lamp ReplacementzRemove the High mounted stop lamp in direction 1 and 2. (as shown above in the illustration)
zDisconnect the connector.Partition
High Mounted
Stop Lamp

242Chapter 7
SRS (Supplemental Restraint System)Section 1 SRS-General InformationI. PRECAUTIONFor safe reasons, read the following precautions before starting any operation.
1. When servicing the SRS, correct sequence and items are described in the following chapter.
2. Instruments and special tools recommended in this chapter shall be used for operation.
3. When servicing the following components, replace them with the new ones if there is a failure.
(1) SRS ECU
(2) Clock Spring Module
(3) Driver Airbag Module
(4) Passenger Airbag Assembly (Option)
4. If there is any abnormality in the wire harness of the SRS, replace it with a new one. Correct or replace the
abnormal wire harness in accordance with Table 1.
Figure 1 (Table 1)No De signation De scription
1 Belt-pretensioner, Driver, Low Seat belt pretensioner, driver side, low position
2 Belt-pretensioner, Driver, High Seat belt pretensioner, driver side, high position
3 Belt-pretensioner, Passenger, High Seat belt pretensioner, passenger side, high position
4 Belt-pretensioner, Passenger, Low Seat belt pretensioner, passenger side, low position
5 IGN Battery voltage
6 GND Ground-ground w ire
7 WL Airbag w arning light
9 K Diagnostic serial data I/O (K line)
10 DAB Hi Driver airbag, high positionE C U T e r mina l D e s c r ipt ion

2435. Servicing operation shall be carried out 60s after the negative
(-) terminal cable is disconnected from the battery. In addition,
the disconnected negative (-) terminal cable shall be protected
with insulating tape for insulation.
In order to deploy an airbag within a certain time period after the
battery is disconnected, condenser in the ECU shall retain some
electrical energy. Otherwise, it could lead to a serious accident
because of the unexpected deployment of airbag.
6. During spray paint work, ECU, airbag assembly, clock spring
assembly, etc shall be removed and kept in place to avoid the effects of overheat. (Over 93¡æ)
7. When the SRS is serviced, a diagnostic scan meter is used to clear the DTC to enable the normal work of
the warning light.1 1 D AB Lo D r iv er a ir b ag , lo w p o s it io n
13 (Option) PAB Hi Passenger airbag, high position
14 (Option) PAB Lo Passenger airbag, low position
20Passenger Airbag Deactivation
Indic atorPassenger airbag deac tivation indic ator light
27PPD/ Passenger Airbag
Deac tivation Sw itch, HighPassenger airbag deac tivation sw itc h, high position
30 Crash Output Crash outputInsulating TapeBatteryCableDriver Side
Warning LampPassenger Side
Warning LampDriver Seat Inflation
Element & AirbagCrash Sensor &
Diagnostic ModuleFront/RH Inflation
Element & Airbag

253Yes: continue with next step.
No: check the circuit, repair it and continue with step (5).
8Turn the ignition switch to LOCK.
9Check the continuity of the terminal of instrument connector and that of diagnostic interface (check the
two ends of K line).
Yes: continue with next step.
No: repair or replace the wire harness. Continue with step (5).
VMake sure to disconnect the negative terminal cable from the battery and wait for at least 60s.Disconnect
the ECU connector. 11Disconnect the connectors of the instrument cluster 12 Are the connector terminals 5, 7 and 9 and those of instrument cluster continuity?
Yes: continue with next step.
No: replace the wire harness, and then continue with step (5). 13Remove ECU and see whether the terminals are in good condition and whether the shorting bar is
broken.
Yes: replace the ECU.
No: reconnect the ECU connector, and then continue with next step.
(3) Make sure of the nonrecurrence of the trouble after repair
1Turn the ignition switch to LOCK.
2Disconnect the negative (-) terminal cable from the battery and wait for at least 60s.
3Connect all the ECU connectors.
4Connect the connector of driver airbag assembly.
5Connect the connector of passenger airbag assembly.
6Connect the connectors of driver and passenger seat belt pretensioners (vehicle with pretensioner).
7Connect clock spring connector.
8Connect the negative (-) terminal cable of the battery.
9Turn the ignition switch to ON.
VIs the SRS warning light working normal?
Yes: the trouble is eliminated. Explain the repair procedures to the Customer.
No: recheck symptoms of the trouble. Repeat these procedures from the first step if the trouble reoccurs.

255(3) Check the wire harness between the fuse box and the connector of the SRS unit
CAUTION
If it is not handled properly, the airbag assembly may be triggered and deployed, leading to serious injury to a
person. Therefore, prior to handling, read the service cautions carefully. See service cautions for SRS.
1Turn the ignition switch to LOCK.
2Loosen the negative (-) terminal cable from the battery and wait for over 1 minute.
3Remove steering column hood.
4Loosen the connector of the clock spring.
5Remove glove box (along with passenger airbag assembly)
6Loosen passenger airbag assembly connectors.
7Remove left trim plate.
8Loosen all the SRS unit connectors.
9Reconnect the negative (-) terminal cable of the battery and turn ignition switch ON, check whether the
electrical potential between pins 5 and 6 (ground) of the connector of SRS unit is higher than 9V.
Yes: continue with next step.
No: replace the wire harness.
VTurn the ignition switch to LOCK. 11 Loosen the negative (-) terminal cable from the battery and wait for over 1 minute. 12 Remove left trim plate. 13 Disconnect the adaptor connector of SRS unit. 14 Reconnect the battery negative (-) terminal cable and turn the ignition switch ON, check whether the
voltage between the corresponding pin of the connector and the pin (ground) is higher than 9V.
Yes: completion of trouble diagnosis.
No: replace the wire harness.
5. Driver side troubleDTC
B1 346
B1 347
B1 348
B1 349
CAUTION
● If it is not handled properly, the airbag assembly may be triggered and deployed,leading to s erious injury to a person. Therefore, prior to handling, read the service cautionscarefu lly .
See s erv ice cau t io n s fo r SRS
If there is driver airbag
● The resistance between terminals of the SRS unit connectors is out of range.
The wire harness of the driver airbag of SRS is short or open circuited.
● Driv er airb ag as s emb ly tro u ble.
● Clock spring internal trouble.
● Trouble of the connector of the circuit between clock spring and SRS ECU.
● The wire harness between clock spring and SRS ECU is open or short-circuited.
● In co rrect in s ert io n o f t h e co n n ect o r o f t h e d riv er airb ag g en erat o r o f SRS. Driver airbag trouble (high or low resistance, short circuit, ground, etc.)
Ch e c kin g Co n d it io n s
Pos s ib le caus e

256DIAGNOSTIC PROCEDURES
(1) Check clock spring
CAUTION
If it is not handled properly, the airbag assembly may be triggered and deployed, leading to serious injury to a
person. Therefore, prior to handling, read the service cautions carefully.
See service cautions for SRS.
yDo the related parts of the clock spring work normal? (Are the pins correctly correlated? There should
be no unnecessary short or open circuit, etc). If possible, use a new clock spring to replace the present
one.
Normal: continue with next step.
Abnormal: replace the clock spring.
See SRS-Clock Spring, Removal & Installation.
(2) Ascertain the trouble exists in driver airbag assembly or other parts
1Replace with a new driver airbag assembly.
2Reconnect the negative (-) terminal cable of the battery.
3Turn the ignition switch ON.
4Any DTC displayed? Can it be cleared?
Yes: replace the driver airbag assembly.
See SRS- Driver Airbag Assembly, Removal & Instillation.
No: continue with next step.
(3) Check the connector of clock spring wire harness
1Turn the ignition switch to LOCK.
2Loosen the negative (-) terminal cable from the battery and wait for over 1 minute.
3Remove steering column hood.
4Loosen the connector of the clock spring.
5Are the connectors of the clock spring normal? (Are the pins correctly correlated? There should be no
unnecessary short or open circuit, etc). If possible, use a new clock spring to replace the present one.
Normal: continue with next step.
Abnormal: replace the wire harness.
See SRS-Clock Spring, Removal & Installation.
(4) Check the wire harness between clock spring and SRS ECU
1Turn the ignition switch to LOCK.
2Loosen the negative (-) terminal cable from the battery and wait for over 1 minute.
3Remove glove box (along with passenger airbag assembly).
4Loosen passenger airbag assembly connectors.

2575Remove left trim plate.
6Loosen all the SRS unit connectors.
7Check the wire harness between the connector terminals of SRS unit and that of clock spring for the
following:
yGround.
yShort circuit with power supply.
yOpen circuit.
8Is the above-mentioned wire harness normal?
9Normal: completion of trouble diagnosis, and install all the parts.
VAbnormal: replace the wire harness.
6. Passenger side trouble
DIAGNOSTIC PROCEDURES
(1) Is there any passenger airbag assembly installed on the vehicle?
Yes: continue with next step.
No: continue with step (5).
(2) Check the cautions of passenger airbag assembly connector
yIf it is not handled properly, the airbag assembly may be triggered and deployed, leading to serious injury
to a person. Therefore, prior to handling, read the service cautions carefully.
See service cautions for SRS.DTC
B1 352
B1 353
B1 354
B1 355
CAUTION
●
If it is not ha ndle d prope rly, the a irba g a ssembly a nd retrac ta ble sea t belt ma y be
trigge re d a nd deploye d/te nsione d, le a ding to serious injury to a pe rson. There fore , prior
t o ha ndling, r e a d t he s e r vic e c a ut ions c a r e f ully.
See service cautions for SRS.
If there is passenger airbag●
The re sistanc e be twe e n pins 13 a nd 14 of SRS unit c onne ctor is out of range
●
The wire ha rness betwe en pins 13 a nd 14 of the SRS unit is short c irc uited●
P ins 13 a nd 14 of the SRS unit c onnec tor are ope n c ircuite d, e .g. the re is nopassenger airbag
●
Passenger airbag assembly trouble
●
Trouble of the conne c tor be twe e n pa ssenger airbag a ssembly a nd SRS ECU
●
Trouble of the conne c tor be twe e n the SRS unit and ground point
●
The circuit between passenger airbag assembly and SRS ECU is open or short
●
The c irc uit betwee n SRS unit a nd ground point is open or short●
SRS unit trouble P a sse nge r airba g a sse mbly trouble (high or low resista nc e , short c ircuit, ground, etc .)
Checking
conditions
P ossible Cause