2007 SSANGYONG RODIUS Service Manual

0-5
WIPER/WASHER SYSTEM
RODIUS 2006.09
0000-00
2. COMPONENTS LOCATOR OF FRONT WIPER
ASSEMBLY
Wiper blade
Wiper linkage
Wiper motor

0-6
RODIUS 2006.09
0000-00
WIPER/WASHER SYSTEM
3. COMPONETS LOCATOR OF REAR WIPER
ASSEMBLY
Rear wiper assembly
Rear wiper motor
Wiper blade assembly

0-7
WIPER/WASHER SYSTEM
RODIUS 2006.09
0000-00
4. CIRCUIT DIAGRAM OF WIPER & WASHER

0-3
PARKING AID SYSTEM
RODIUS 2006.09
8790-04
8790-04PARKING ASSISTANCE SYSTEM
1. COMPONENT SPECIFICATIONS OF PARKING AID
SYSTEM
The parking aid system emits the supersonic wave signals from the sensors on the rear bumper
with a specific interval and detects the reflected signals from obstacles while the gear selecto
r
lever is in “R” position.
The number of displaying bars is decreased and the alarm interval becomes faster as the
obstacle approaches. This supplementary system is to secure the safety distance for parking.
Parking aid unit
Detecting type: Super sonic wave
Detecting distance: 25 ~ 120 cm
(distance between sensor and obstacle)
1)
Parking aid sensor
- Type: Piezo ceramic element
- Frequency: 40 KHz ± 2 KHz
- Detecting range (13.5 V)
* Horizontal: Min. 20° at 110 ± 5 cm Min. 1 00° at 50 ± 5 cm
* Vertical: Min. 20° at 110 ± 5 cm Min. 60° at 50 ± 5 cm
2)

0-4
RODIUS 2006.09
8790-04
PARKING AID SYSTEM
Grear selector lever
Applies power to parking aid system
Rearview camera
1. COMPONENTS OF PARKING AID SYSTEM (PARKING AID SYSTEM + REARVIEW CAMERA)
1) REARVIEW CAMERA EQUIPPED VEHICLE
When moving the gear selector lever into R (Reverse) position while watching DVD or VCD, the
rearview appears on the front monitor but the rear monitor continuously shows current screen.
The video mode in front A/V system is changed to rearview monitoring mode. However, the
audio mode stays on.
The video mode in front A/V system resumes when shifting out from “R” position.
The audio and video mode in rear A/V system are not changed.
When selecting R position while A/V system is not in use:
Both monitors are automatically turned on to display rearview.
Both monitors are automatically turned off when shifting out from “R” position.
-
-
-
-
- When selecting R position while A/V system is in use:

0-5
PARKING AID SYSTEM
RODIUS 2006.09
8790-04
Multi-meter
Front monitor ICM box
Even in other modes, it is changed to the parking aid
screen when moving the gear selector lever into
“R” position.
When moving the gear selector lever into “R”
position
while watching DVD or VCD, the rearview appears on
the front monitor.
When moving the gear selector lever into “R”
position, the alarm buzzer in ICM box sounds (installed
at bottom of STICS).
Parking aid sensor(Rear bumper)
The three parking aid sensors send the distance data
between rear bumper and obstacle to PAS unit.
Rearview camera
The rearview camera sends the rearview to the monitor
by using wide angle lens.
PAS unit
It is a control unit for the parking aid system (PAS) and
transmits the signals from sensors to multimeter and
buzzer.(installed in tuner/amplifier bracket)

0-6
RODIUS 2006.09
8790-04
PARKING AID SYSTEM
The inside of the ICM BOX The outside of the ICM BOX
2. COMPONENTS OF PARKING AID SYSTEM(PAS)
1) parking AID SYSTEM COMPOSITION
Multi-meter Rear center obstacles
Rear right sensor
Rear right obstacles Rear left obstacles
Parking aid buzzer Rear left sensor
Rear center sensor

0-7
PARKING AID SYSTEM
RODIUS 2006.09
8790-04
PAS UNIT The message on MULTI-METER
Center sensor
This unit controls the parking aid system. One of 3 LEDs comes on when the corresponding
parking aid sensor is defective and shows below message on multi-meter.
Amplifier withbuilt-in DSP
Navigation unit
Tuner
Right sensor Left sensor