2007 SATURN RELAY Owners Manual

1. Loosen the wheel
nuts using the
folding wrench,
but do not
remove them.Turn the handle counterclockwise about
180 degrees, then ip the handle back to the
starting position. This avoids taking the
wrench off the lug nut for each turn.
Notice:If your vehicle has wheel locks and
you use an impact wrench to remove the wheel
nuts, you could damage the lock nut or
wheel lock key. Do not use an impact wrench
to remove the wheel nuts if your vehicle
has wheel locks.
Notice:If you use a jack to raise the vehicle
without positioning it correctly, you could
damage your vehicle. When raising your
vehicle on a jack, avoid contact with the rear
axle control arms.
Notice:If you position the jack under the
rocker molding and attempt to raise the
vehicle, you could break the molding and/or
cause other damage to your vehicle. Always
position the jack so that when the jack head is
raised, it will t rmly in the notch located
inboard from the rocker molding.
489
ProCarManuals.com

A. Front Location
B. Rear Location
2. Near each wheel, there is a notch (A and B)
in the vehicle’s frame, inboard of the rocker
molding. Position the jack and raise the
jack head until it ts rmly into the notch in
the vehicle’s frame nearest the at tire.
Do not raise the vehicle yet.
3. Put the compact spare tire near you.
{CAUTION:
Getting under a vehicle when it is jacked
up is dangerous. If the vehicle slips off
the jack you could be badly injured or
killed. Never get under a vehicle when it
is supported only by a jack.
{CAUTION:
Raising your vehicle with the jack
improperly positioned can damage the
vehicle and even make the vehicle fall.
To help avoid personal injury and vehicle
damage, be sure to t the jack lift head
into the proper location before raising the
vehicle.
490
ProCarManuals.com

4. Attach the folding wrench (A) to the jack (B),
and turn the wrench clockwise to raise the
jack head approximately 3 inches (7.6 cm).5. Raise the vehicle by turning the folding
wrench clockwise in the jack. Raise the
vehicle far enough off the ground so there
is enough room for the compact spare tire
to t under the wheel well.
491
ProCarManuals.com

6. Remove all the wheel nuts and take off the
at tire.
{CAUTION:
Rust or dirt on the wheel, or on the parts
to which it is fastened, can make the
wheel nuts become loose after a time.
The wheel could come off and cause an
accident. When you change a wheel,
remove any rust or dirt from the places
where the wheel attaches to the vehicle.
In an emergency, you can use a cloth
or a paper towel to do this; but be sure
to use a scraper or wire brush later, if
needed, to get all the rust or dirt off.7. Remove any rust or
dirt from the wheel
bolts, mounting
surfaces and spare
wheel.
{CAUTION:
Never use oil or grease on studs or nuts.
If you do, the nuts might come loose.
Your wheel could fall off, causing a
serious accident.
492
ProCarManuals.com

8. Install the compact
spare tire and
put the wheel nuts
back on with
the rounded end of
the nuts toward
the wheel.
Tighten each nut by hand until the wheel is
held against the hub.
9. Lower the vehicle by attaching the folding
wheel wrench to the jack and turning the
wrench counterclockwise. Lower the
jack completely.
493
ProCarManuals.com

{CAUTION:
Incorrect wheel nuts or improperly
tightened wheel nuts can cause the wheel
to come loose and even come off. This
could lead to an accident. Be sure to use
the correct wheel nuts. If you have to
replace them, be sure to get new GM
original equipment wheel nuts. Stop
somewhere as soon as you can and have
the nuts tightened with a torque wrench
to the proper torque specication. See
Capacities and Specifications on page 518
for wheel nut torque specication.
Notice:Improperly tightened wheel nuts can
lead to brake pulsation and rotor damage.
To avoid expensive brake repairs, evenly
tighten the wheel nuts in the proper sequence
and to the proper torque specication.
SeeCapacities and Specifications on page 518
for the wheel nut torque specication.10. Tighten the wheel
nuts rmly in a
crisscross sequence,
as shown.
Notice:Wheel covers will not t on your
compact spare. If you try to put a wheel cover
on the compact spare, you could damage
the cover or the spare.
11. Do not try to put a wheel cover on the
compact spare tire. It will not t. Store
the wheel cover securely in the rear of the
vehicle until you have the at tire repaired
or replaced.
494
ProCarManuals.com

Secondary Latch System
Your vehicle may have an underbody-mounted tire
hoist assembly equipped with a secondary latch
system. It is designed to stop a tire from suddenly
falling off your vehicle if the cable holding the
spare tire is damaged. For the secondary latch to
work, the tire must be stowed with the valve
stem pointing down.
Your vehicle uses the underbody tire hoist
assembly to store either the compact spare or
a at road tire. SeeStoring a Flat or Spare
Tire and Tools on page 497for instructions on
storing the spare or at tire correctly.{CAUTION:
Before beginning this procedure read all
the instructions. Failure to read and follow
the instructions could damage the hoist
assembly and you and others could get
hurt. Read and follow the instructions
listed next.
{CAUTION:
Someone standing too close during the
procedure could be injured by the jack.
If the spare tire does not slide off the jack
completely, make sure no one is behind
you or on either side of you as you pull
the jack out from the spare.
495
ProCarManuals.com

To release the spare tire from the secondary latch,
do the following:
1. Place the jack under the vehicle, ahead of
the rear bumper. Position the center lift
point of the jack under the center of the
compact spare tire.2. Turn the folding wrench clockwise to raise
the jack until it lifts the secondary latch
device under the wheel plate.
3. Keep raising the jack until the compact spare
tire stops moving upward and is held rmly in
place. This lets you know that the secondary
latch has released.
4. Lower the jack by turning the folding wrench
counterclockwise. Keep lowering the jack until
the compact spare tire is resting on the
folding wrench.
496
ProCarManuals.com