2007 NISSAN TIIDA sensor

P0335 CKP SENSOR
EC-1149
< COMPONENT DIAGNOSIS >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
P0335 CKP SENSOR
DTC LogicINFOID:0000000001162612
DTC DETECTION LOGIC
NOTE:
Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC is declared present with the engine cranking or idling.
If the DTC is present:
-Malfunction indicator (Red) lights up.
Diagnosis ProcedureINFOID:0000000001162613
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E15. Refer to Ground inspection in GI-58, "
Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK CKP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect crankshaft position (CKP) sensor harness connector.
3. Disconnect ECM harness connector.
4. Check the continuity between CKP sensor harness connector and ECM harness connector.
5. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK CKP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check the continuity between CKP sensor harness connector and ECM harness connector.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK CKP SENSOR
Refer to EC-1150, "
Component Inspection".
DTC No. Trouble diagnosis name Possible cause
P0335CRANKSHAFT POSITION SENSOR CIRCUIT
 1.DEF: Signal incoherence
 2.DEF: No signal
 3.DEF: Signal out side level
 4.DEF: Value out side level
 5.DEF: Configuration/ initialisation Harness or connectors
(The sensor circuit is open or shorted.)
 Crankshaft position sensor
 Signal plate
CKP sensor ECM
Continuity
Connector Terminal Connector Terminal
F15 2 F11 88 Existed
CKP sensor ECM
Continuity
Connector Terminal Connector Terminal
F15 1 F11 84 Existed

EC-1150
< COMPONENT DIAGNOSIS >[K9K]
P0335 CKP SENSOR
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace crankshaft position sensor.
5.CHECK GEAR TOOTH
Visually check for chipping flywheel gear tooth.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Replace signal plate.
6.CHECK INTERMITTENT INCIDENT
Refer to GI-55, "
Intermittent Incident".
>>INSPECTION END
Component InspectionINFOID:0000000001162614
1.CHECK CKP SENSOR
1. Turn ignition switch OFF.
2. Disconnect CKP sensor harness connector.
3. Check resistance between CKP sensor terminals as follows.
Is the inspection result normal?
YES >>INSPECTION END
NO >> Replace CKP sensor.
Terminals Resistance
1 and 2 612 - 748Ω

P0340 CMP SENSOR
EC-1151
< COMPONENT DIAGNOSIS >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
P0340 CMP SENSOR
DTC LogicINFOID:0000000001162615
DTC DETECTION LOGIC
NOTE:
Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC is declared present after the engine is started or following a load test.
Special note:
Longer starting time, requires several attempts to start the vehicle.
Diagnosis ProcedureINFOID:0000000001162616
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E15. Refer to Ground inspection in GI-58, "
Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK CMP SENSOR POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect camshaft position (CMP) sensor harness connector.
3. Turn ignition switch ON.
4. Check the voltage between CMP sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.DETECT MALFUNCTIONING PART
Check the following.
 Harness connectors E8, F8
 Harness for open or short between ECM and CMP sensor
 Harness for open or short between IPDM E/R and CMP sensor
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK CMP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between CMP sensor harness connector and ECM harness connector.
DTC No. Trouble diagnosis name Possible cause
P0340CAMSHAFT POSITION SENSOR CIRCUIT
 1.DEF: Signal incoherence
 2.DEF: No signal
 3.DEF: Value out side level
 4.DEF: Configuration/ initialisation Harness or connectors
(The sensor circuit is open or shorted.)
 Camshaft position sensor
Timing belt
 Signal plate
CMP sensor
Ground Voltage
Connector Terminal
F21 3 Ground Battery voltage

EC-1152
< COMPONENT DIAGNOSIS >[K9K]
P0340 CMP SENSOR
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
5.CHECK CMP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check the continuity between CMP sensor harness connector and ECM harness connector.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
6.CHECK CMP SENSOR
Refer to EC-1152, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Replace camshaft position sensor.
7.CHECK SPROCKET
Visually check for chipping signal plate gear tooth.
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair or replace sprocket.
8.CHECK TIMING BELT
Refer to EM-291, "
Removal and Installation".
Is the inspection result normal?
YES >> GO TO 9.
NO >> Replace timing belt.
9.CHECK INTERMITTENT INCIDENT
Refer to GI-55, "
Intermittent Incident".
>>INSPECTION END
Component InspectionINFOID:0000000001162617
1.CHECK CMP SENSOR
1. Reconnect all harness connectors disconnected.
2. Start engine and warm it up to normal operating temperature.
3. Measure the voltage signal between ECM harness connector and ground under the following conditions.
CMP sensor ECM
Continuity
Connector Terminal Connector Terminal
F21 1 F11 65 Existed
CMP sensor ECM
Continuity
Connector Terminal Connector Terminal
F21 2 F11 75 Existed

P0340 CMP SENSOR
EC-1153
< COMPONENT DIAGNOSIS >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
Is the inspection result normal?
YES >>INSPECTION END
NO >> Replace CMP sensor.
+-
Condition Voltage
Connector Terminal Connector Terminal
F1175
(CMP sensor
signal)E16 128[Engine is running]
Warm-up condition
 Idle speed
NOTE:
The pulse cycle
changes depending on
rpm at idle.0 - 1V
[Engine is running]
Warm-up condition
 Engine speed: 2,000
rpm0 - 1V
MBIB1510E
MBIB1511E

EC-1158
< COMPONENT DIAGNOSIS >[K9K]
P0409 EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR
P0409 EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR
DTC LogicINFOID:0000000001162623
DTC DETECTION LOGIC
NOTE:
If DTC P0409 is displayed with DTC P0651, first perform trouble diagnosis for DTC P0651. Refer to
EC-1182, "
DTC Logic".
Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC is declared present after the engine started.
If the DTC is present:
-Malfunction indicator (Yellow) lights up.
Diagnosis ProcedureINFOID:0000000001162624
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E15. Refer to Ground inspection in GI-58, "
Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR POWER SUPPLY CIRCUIT
1. Disconnect EGR volume control valve harness connector.
2. Turn ignition switch ON.
3. Check the voltage between EGR volume control valve control position sensor connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR GROUND CIRCUIT FOR
OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between EGR volume control valve control position sensor harness connector and
ECM harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
DTC No. Trouble diagnosis name Possible Cause
P0409EGR VOLUME CONTROL VALVE CONTROL POSITION SEN-
SOR CIRCUIT
 CO.0: Open circuit or short circuit to ground
 CC.1: Short circuit to +12V Harness or connectors
(The EGR volume control valve control position
sensor circuit is open or shorted.)
 EGR volume control valve control position sensor
EGR volume control valve control position sensor
Ground Voltage
Connector Terminal
F52 1 Ground Approx. 5V
EGR volume control valve control posi-
tion sensorECM
Continuity
Connector Terminal Connector Terminal
F52 3 E16 82 Existed

P0409 EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR
EC-1159
< COMPONENT DIAGNOSIS >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
4.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR INPUT CIRCUIT FOR OPEN
AND SHORT
1. Check the continuity between EGR volume control valve control position sensor harness connector and
ECM harness connector.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
5.CHECK INTERMITTENT INCIDENT
Refer to GI-55, "
Intermittent Incident".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace.
6.REPLACE EGR VOLUME CONTROL VALVE
1. Replace the EGR volume control valve.
2. Perform EC-1055, "
EGR VOLUME CONTROL VALVE CLOSED POSITION LEARNING : Special Repair
Requirement"
>>INSPECTIO END
EGR volume control valve control posi-
tion sensorECM
Continuity
Connector Terminal Connector Terminal
F52 5 E16 86 Existed

EC-1162
< COMPONENT DIAGNOSIS >[K9K]
P0488 EGR SYSTEM
P0488 EGR SYSTEM
DTC LogicINFOID:0000000001162628
DTC DETECTION LOGIC
NOTE:
Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC is declared present after the engine is started.
Special notes:
- Engine instability, possibly even stalling.
- Difficult to start engine or even impossible when cold.
- Loss of performance.
- Possible smoke emissions.
-Malfunction indicator (Red) lights up.
Diagnosis ProcedureINFOID:0000000001162629
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E15. Refer to Ground inspection in GI-58, "
Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK EGR VOLUME CONTROL VALVE INSTALLATION
Check that EGR volume control valve is installed properly.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Install EGR volume control valve properly.
3.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR POWER SUPPLY CIRCUIT
1. Disconnect EGR volume control valve harness connector.
2. Turn ignition switch ON.
3. Check the voltage between EGR volume control valve control position sensor connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR GROUND CIRCUIT FOR
DTC No. Trouble diagnosis name Possible cause
P0488EGR VOLUME CONTROL
 1.DEF: Signal incoherence
 2.DEF: Signal outside lower level
 3.DEF: Signal outside upper level
 4.DEF: Valve outside level
 5.DEF: Defective sensor Harness or connectors
(The EGR volume control valve circuit is open
or shorted.)
(The EGR volume control valve control posi-
tion sensor circuit is open or shorted.)
 EGR volume control valve
 EGR volume control valve control position
sensor
 Incorrect EGR volume control valve installa-
tion
 EGR volume control valve stuck closed
 EGR passage clogged
GR volume control valve control position sensor
Ground Voltage
Connector Terminal
F52 1 Ground Approx. 5V