SHIFT CONTROL SYSTEM
TM-203
< ON-VEHICLE REPAIR >[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
When installing the control cable (1) to the control device assembly
(2), make sure that the control cable (1) is fully pressed in with the
ribbed surface (A) facing downward from the vehicle.
: Vehicle front
After installation is completed, adjust and check the A/T position.
Refer to TM-204, "
Adjustment of A/T Position" and TM-204,
"Checking of A/T Position".
Control Device Disassembly and AssemblyINFOID:0000000001731376
DISASSEMBLY
NOTE:
Refer to TM-200, "
Control Device Removal and Installation" to disassemble.
1. Remove selector lever knob from control device assembly. Refer to TM-203, "
Selector Lever Knob
Removal and Installation".
2. Remove position lamp from position indicator plate (1).
3. Insert a flat-bladed screwdriver to (A) (at 4 locations) as shown,
and bend each hook slightly to raise position indicator plate (1)
and remove from control device assembly (2).
4. Remove bracket from control device assembly (2).
5. Remove A/T device harness connector from control device
assembly (2).
6. Release tabs (A) on shift lock solenoid and park position switch
assembly from hooks (B) on control device assembly to shift
lock solenoid and park position switch assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
Selector Lever Knob Removal and InstallationINFOID:0000000001731377
REMOVAL
CAUTION:
Make sure that parking brake is applied before removal/installation.
SCIA6253E
SCIA6969E
SCIA6977E
TM-204
< ON-VEHICLE REPAIR >[TYPE 1 (4AT: RE4F03B)]
SHIFT CONTROL SYSTEM
1. Place the selector lever knob (1) in “N” position.
2. Slide knob cover (2) downward.
3. Pull out lock pin (3) from selector lever knob (1).
4. Remove selector lever knob (1) and knob cover (2) as a set from
selector lever.
CAUTION:
Do not push selector button.
INSTALLATION
1. Insert lock pin (1) to selector lever knob (2).
2. Install knob cover (3) to selector lever knob (2).
3. Place the selector lever in “N” position.
4. Install selector lever knob over selector lever until a click is felt.
CAUTION:
Do not tilt selector lever knob when installing. Install it
straight, and do not tap or apply any shock to install it.
Do not push selector button.
Adjustment of A/T PositionINFOID:0000000001731378
Move selector lever from “P” position to “1” position. You should be able to feel the detents in each position. If
the detents cannot be felt or if the position indicator is improperly aligned, the control cable needs adjustment.
CAUTION:
Make sure that parking brake is applied before adjustment.
1. Remove the air duct assembly. Refer to EM-27, "
Removal and Installation".
2. Remove the control cable nut (A) and control cable (1) and
place the manual lever (2) in the "P' position.
3. Place selector lever in “P” position.
4. Hold control cable (1) at the end and pull it with a force of 9.8 N
(approximately 1 kg, 2.2 lb). Release the control cable and tem-
porarily tighten control cable nut (A).
5. Tighten control cable nut (A) to the specified torque.
CAUTION:
Secure manual lever when tightening nut.
6. Move selector lever from “P” to “1” position again. Make sure that selector lever moves smoothly.
7. Check A/T position. Refer to TM-204, "
Checking of A/T Position".
8. Install air duct assembly. Refer to EM-27, "
Removal and Installation".
Checking of A/T PositionINFOID:0000000001731379
1. Place selector lever in “P” position, and turn ignition switch ON (Do not start engine).
2. Make sure selector lever can be shifted to other than “P” position when brake pedal is depressed. Also
make sure selector lever can be shifted from “P” position only when brake pedal is depressed.
3. Move selector lever and check for excessive effort, sticking, noise or rattle.
4. Confirm selector lever stops at each position with the feel of engagement when it is moved through all the
positions. Check whether or not the actual position selector lever is in matches the position shown by the
shift position indicator and the transaxle.
SCIA6971E
SCIA6972E
Control cable nut : Refer to TM-200, "Control De-
vice Removal and Installation".WCIA0635E
TM-206
< ON-VEHICLE REPAIR >[TYPE 1 (4AT: RE4F03B)]
KEY INTERLOCK CABLE
KEY INTERLOCK CABLE
Removal and InstallationINFOID:0000000001731380
COMPONENTS
REMOVAL
CAUTION:
Make sure that parking brake is applied before removal and installation.
1. Place the selector lever in the “N” position.
2. Remove the selector lever knob. Refer to TM-203, "
Selector Lever Knob Removal and Installation".
3. Remove the center console assembly. Refer to IP-11, "
Removal and Installation".
4. Slide the slider (A) toward the casing cap (B) while pressing tabs
(C) on the slider to separate the slider (A) from the adjust holder
(D).
5. Remove the casing cap (B) from the cable bracket on the control
device assembly.
6. Remove the key interlock cable from the key interlock rod (E).
1. Key interlock cable 2. Key cylinder 3. Control device assembly
A. Lock plate B. Holder C. Clip
D. Slider E. Key interlock rod F. Adjust holder
G. C a s i n g c a p
WCIA0621E
SCIA6975E
TM-330
< FUNCTION DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
A/T CONTROL SYSTEM
Shift Mechanism
INFOID:0000000001714310
CONSTRUCTION
FUNCTION OF CLUTCH AND BRAKE
CLUTCH AND BAND CHART
1. Torque converter 2. Oil pump 3. Input shaft
4. Brake band 5. Reverse clutch 6. High clutch
7. Front sun gear 8. Front pinion gear 9. Front internal gear
10. Front planetary carrier 11. Rear sun gear 12. Rear pinion gear
13. Rear internal gear 14. Rear planetary carrier 15. Forward clutch
16. Forward one-way clutch 17. Overrun clutch 18. Low one-way clutch
19. Low & reverse brake 20. Parking pawl 21. Parking gear
22. Output shaft 23. Idle gear 24. Output gear
SAT998I
Clutch and brake components Abbr. Function
5Reverse clutch R/C To transmit input power to front sun gear 7.
6High clutch H/C To transmit input power to front planetary carrier 10.
15Forward clutch F/C To connect front planetary carrier 10 with forward one-way clutch 16.
17Overrun clutch O/C To connect front planetary carrier 10 with rear internal gear 13.
4Brake band B/B To lock front sun gear 7.
16Forward one-way clutch F/O.CWhen forward clutch 15 is engaged, to stop rear internal gear 13 from rotating in
opposite direction against engine revolution.
18Low one-way clutch L/O.CTo stop front planetary carrier 10 from rotating in opposite direction against en-
gine revolution.
19Low & reverse brake L & R/B To lock front planetary carrier 10.
Shift posi-
tionR/C
5H/C
6F/C
15O/C
17Band servo
F/O.C
16L/O.C
18L&R/B
19Lock-
upRemarks
2nd
apply3rd re-
lease4th ap-
ply
PPA R K
POSITION
RREVERSE
POSITION
TM-332
< FUNCTION DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
A/T CONTROL SYSTEM
Similar to the “N” position, the clutches do not operate. The parking pawl engages with the parking gear to
mechanically hold the output shaft so that the power train is locked.
“11” Position
“D
1” and “21” Positions
SAT991I
Forward clutch
Forward one-way clutch
Overrun clutch
Low & reverse brakeAs overrun clutch engages, rear internal gear is locked by the operation of low and re-
verse brake.
This is different from that of D
1 and 21.
Engine brake Overrun clutch always engages, therefore engine brake can be obtained when deceler-
ating.
SCIA1816E
TM-420
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
A/T SHIFT LOCK SYSTEM
Data are reference values.
Diagnosis ProcedureINFOID:0000000001731062
SYMPTOM 1:
Selector lever cannot be moved from “P” position with ignition switch in ON position and brake
pedal depressed.
Selector lever can be moved from “P” position with ignition key in ON position and brake pedal
released.
Selector lever can be moved from “P” position when ignition switch is removed from key cylinder.
SYMPTOM 2:
Ignition key cannot be removed when selector lever is set to “P” position.
Ignition key can be removed when selector lever is set to any position except “P” position.
1.CHECK KEY INTERLOCK CABLE
Check key interlock cable for damage.
OK or NG
OK >> GO TO 2.
NG >> Repair key interlock cable. Refer to XX-XX, "*****"
.
2.CHECK A/T POSITION
Check A/T position. Refer to XX-XX, "*****"
.
OK or NG
OK >> GO TO 3.
NG >> Adjust control cable. Refer to XX-XX, "*****"
.
3.CHECK SHIFT LOCK SOLENOID AND PARK POSITION SWITCH
1. Turn ignition switch ON. (Do not start engine.)
2. Selector lever is set in “P” position.
3. Check operation sound.
OK or NG
OK >>INSPECTION END
NG >> GO TO 4.
4.CHECK POWER SOURCE
1. Turn ignition switch ON. (Do not start engine.)
TER-
MINAL
NO.WIRE
COLORITEM CONDITIONVOLTAGE
(Approx.)
1 P O/D switchIgnition switch: “ON” Battery voltage
Ignition switch: “OFF” 0V
2 B Ground Always 0V
3 L IlluminationParking lamps: “ON” Battery voltage
Parking lamps: “OFF” 0V
4 B Ground Always 0V
5 LG Shift lock solenoidWhen ignition switch is "ON", brake pedal is depressed and se-
lector lever is set in "P" position.Battery voltage
Except above. 0V
6 B Ground Always 0V
Condition Brake pedal Operation sound
When ignition switch is turned to ON position and selector lever is set in
“P” position.Depressed Yes
Released No
SYSTEM SYMPTOM
TM-437
< SYMPTOM DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
Slips/Will Not EngageRaces extremely fast
or slips in changing
from D
3 to D2 when
depressing accelera-
tor pedal. ON vehicle1. A/T fluid levelXX-XX, "*****"
2. Accelerator pedal position sensor EC-583
3. Line pressure testTM-178
4. Line pressure solenoid valveXX-XX, "*****"
5. Shift solenoid valve BXX-XX, "*****"
6. Control valve assemblyXX-XX, "*****"
OFF vehicle7. Brake bandXX-XX, "*****"8. High clutchXX-XX, "*****"
Races extremely fast
or slips in changing
from D
4 or D3 to D 1
when depressing ac-
celerator pedal.ON vehicle1. A/T fluid levelXX-XX, "*****"
2. Accelerator pedal position sensorEC-583
3. Line pressure testTM-178
4. Line pressure solenoid valveXX-XX, "*****"
5. Shift solenoid valve AXX-XX, "*****"
6. Shift solenoid valve BXX-XX, "*****"
7. Control valve assemblyXX-XX, "*****"
OFF vehicle8. Forward clutchXX-XX, "*****"9. Forward one-way clutchXX-XX, "*****"
10. Low one-way clutchXX-XX, "*****"
Vehicle will not run in
any position.ON vehicle1. A/T fluid levelXX-XX, "*****"
2. Control cable adjustmentXX-XX, "*****"
3. Line pressure testTM-178
4. Line pressure solenoid valveXX-XX, "*****"
OFF vehicle5. Oil pumpXX-XX, "*****"
6. High clutchXX-XX, "*****"
7. Brake bandXX-XX, "*****"
8. Low & reverse brakeXX-XX, "*****"
9. Torque converterXX-XX, "*****"
10. Parking componentsXX-XX, "*****"
OthersEngine cannot be
started in “P” and “N”
positions.
XX-XX, "*****"
ON vehicle1. Ignition switch and starterXX-XX, "*****"
,
XX-XX, "*****"
2. Control cable adjustmentXX-XX, "*****"
3. PNP switch adjustmentXX-XX, "*****"
Engine starts in posi-
tions other than “P”
and “N”.ON vehicle1. Control cable adjustmentXX-XX, "*****"
2. PNP switch adjustmentXX-XX, "*****"
Items Symptom Condition Diagnostic item Reference page
TM-438
< SYMPTOM DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
SYSTEM SYMPTOM
OthersTransaxle noise in“ P”
and “N” positions.ON vehicle1. A/T fluid levelXX-XX, "*****"
2. Line pressure testTM-178
3. Accelerator pedal position sensorEC-583
4. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
OFF vehicle5. Oil pumpXX-XX, "*****"6. Torque converterXX-XX, "*****"
Vehicle moves when
changing into “P” po-
sition or parking gear
does not disengage
when shifted out of “P”
position.ON vehicle 1. Control cable adjustmentXX-XX, "*****"
OFF vehicle 2. Parking componentsXX-XX, "*****"
Vehicle runs in “N” po-
sition.
XX-XX, "*****"
ON vehicle 1. Control cable adjustmentXX-XX, "*****"
OFF vehicle2. Forward clutchXX-XX, "*****"3. Reverse clutchXX-XX, "*****"
4. Overrun clutchXX-XX, "*****"
Vehicle braked when
shifting into “R” posi-
tion.ON vehicle1. A/T fluid levelXX-XX, "*****"
2. Control cable adjustmentXX-XX, "*****"
3. Line pressure testTM-178
4. Line pressure solenoid valveXX-XX, "*****"
5. Control valve assemblyXX-XX, "*****"
OFF vehicle6. High clutchXX-XX, "*****"7. Brake band XX-XX, "*****"
8. Forward clutchXX-XX, "*****"
9. Overrun clutchXX-XX, "*****"
Excessive creep. ON vehicle 1. Engine idling speedEC-389
Engine stops when
shifting lever into “R”,
“D”, “2” and “1” posi-
tions.ON vehicle1. Engine idling speedEC-3892. A/T fluid levelXX-XX, "*****"
3. Torque converter clutch solenoid valveXX-XX, "*****"
4. Control valve assemblyXX-XX, "*****"
OFF vehicle 5. Torque converterXX-XX, "*****"
Vehicle braked by
gear change from D
1
to D
2.ON vehicle 1. A/T fluid levelXX-XX, "*****"OFF vehicle2. Reverse clutchXX-XX, "*****"3. Low & reverse brakeXX-XX, "*****"
4. High clutchXX-XX, "*****"
5. Low one-way clutchXX-XX, "*****"
Vehicle braked by
gear change from D
2
to D
3.ON vehicle 1. A/T fluid levelXX-XX, "*****"OFF vehicle 2. Brake bandXX-XX, "*****"
Items Symptom Condition Diagnostic item Reference page