2007 NISSAN 350Z Soft top

SOFT TOP
RF-121
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
5. Lower The Soft Top 5th Bow

Remove both operating rod of soft top 5th bow.
CAUTION:
Remove a holder of operating rod end.
Simultaneously hold soft top 5th bow by hand when remov-
ing the holder.

Push in 5th bow to storage lid (do half lock).
CAUTION:
After closing the soft top manually according to the above pro-
cedures, have the soft top operation system checked and/or
repaired by a NISSAN dealer as soon as possible.
Avoid leaving the vehicle outside for long periods or driving at
high speed. As the rear of the soft top is not locked completely,
this may allow wind and rain get into the vehicle.
MANUAL OPERATION (SOFT TOP FULLY CLOSE
FULLY OPEN)
1. Remove The Luggage Floor Trim
Remove the rear floor box and luggage floor finisher upper. Refer to EI-41, "Removal and Installation (for
Roadster Models)" .
2. Cutting Storage Room Finisher
Cut storage room finisher from seat side.
3. Unlock The Storage Lid

Remove clip of inspection cover.

Remove the storage lid inspection cover.

Pull the unlock wire then unlock the soft top 5th bow.
PIIA7594E
PIIA8845E
PIIA8844E
PIIB1438E

RF-122
SOFT TOP
Revision: 2006 November2007 350Z
4. Open The Soft Top 5th Bow

Remove both shock absorber of soft top 5th bow.

Open the soft top 5th bow (approximate 90 degrees)
5. Open The Trunk Lid

Pull the emergency cable.

Open the trunk lid.
6. Open The Storage Lid

Remove floorboard inside of the trunk.

Disconnect the storage lid motor harness connector downward
which is in the right hand side of the trunk.

Pull down the storage lid lock release cable (right and left side of
the trunk).

Confirm a clicking sound of lock release.

Pull up the storage lid from the right and left sides of vehicle (two
people are required).
CAUTION:
The storage lid is extremely heavy. Pulling it up should be
done by two people. Use Hex-wrench to rotate the axis of
the gear, when storage lid does not move.

Disconnect roof actuator harness connector right and left side (disconnect top of roof actuator harness
connector right and left side).
7. Open The Soft Top

Lower the soft top 5th bow.

Unlock the front lock.

Open the soft top right and left side of the vehicle slowly by hand (two person job).
8. Close The Storage Lid
NOTE:
If necessary.
9. Close The Trunk Lid
NOTE:
If necessary.
PIIB1437E

RF-126
STORAGE LID
Revision: 2006 November2007 350Z
Removal and Installation of Storage Lid ActuatorNIS00081
REMOVAL
1. Remove trank room trim.
2. Remove nuts and bolts, and then remove storage lid lower
bracket.
3. Disconnect storage lid actuator harness connector.
4. Remove nuts and remove storage lid actuator from storage lid
bracket, lower.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Storage Room FinisherNIS00082
REMOVAL
1. Remove rear side finisher. Refer to EI-37, "REAR SIDE FINISHER" .
2. Remove bolts, and then soft top mounting bracket (front).
3. Remove bolts, and then soft top mounting bracket (rear).
4. Lift up soft top mounting bracket using a lever, and then remove storage room finisher clips.
5. Remove storage room finisher clips, and then remove rear side of storage room finisher.
PIIA7972E
PIIA8625E
PIIA7627E

STORAGE LID
RF-127
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
6. Lift up back panel finisher clips using remover tools, and then remove front side of storage room finisher.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Storage Outer Protector NIS00083
Note the following, and install in the reverse order of removal.
1. Heat the bonded area using a hair dryer, and then remove stor-
age outer protector.
NOTE:
Do not reuse storage outer protector after removing.
2. Remove storage room finisher.
3. Clean Storage lid surface.
4. Close Soft top, and draw a line on a storage lid just behind the 5th bow out side edge by a water base
marker pen.
5. Apply IPA solution (isopropyl alcohol : water = 1 : 1) on the lid, and set the storage outer protector position
from one side. And do the same procedure to another side.
6. Apply left side storage lid outer aligning with left storage lid scribed line.
7. Apply right side storage lid outer aligning with right storage lid scribed line.
NOTE:
Not to put air or dust under the tape.
After applying the tape on the lid, peal off the protection film on the storage outer protector.
PIIB1177E
PIIB1443E