2007 NISSAN 350Z 5th bow motor voltage

SOFT TOP
RF-33
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Terminal and Reference Value of Soft Top Control UnitNIS0006H
CLOSE → OPEN OPERATION
The operation chart for roof position. Refer to RF-19, "State Chart" .
Te r m i -
nal No.Wire
colorDescription
Condition
(Roof position: OP)Value (V)
(Approx.)
Signal nameInput/
Output
1 W/R Battery power supply Input — Battery voltage
3RRoof actuator RH
(OPEN) signalOutputOP8 → OP11 0 → Battery voltage → 0
Other than above 0
4G/R5th bow closure motor
(CLOSE) signalOutput — 0
5R/BStorage lid actuator RH
(OPEN) signalOutputOP6 → OP7
0 → Battery voltage → 0
OP12
Other than above 0
6 R 5th bow unlock actuator signal OutputOP2 → OP3 0 → Battery voltage → 0
Other than above 0
7 B Ground — — 0
8 W/R Battery power supply Input — Battery voltage
10 YRoof actuator RH
(CLOSE) signalOutput — 0
12 G/Y5th bow closure motor
(OPEN) signalOutputOP4 0 → Battery voltage → 0
Other than above 0
13 L/RStorage lid actuator RH
(CLOSE) signalOutputOP11 → OP12 0 → Battery voltage → 0
Other than above 0
14 W Speed signal (8 pulse)Input/
OutputSpeed meter operate
[When vehicle speed is
Approx. 40km/h (25 MPH)]
15 ORStorage lid unlock actuator LH and
RH signalOutputOP5 → OP6 0 → Battery voltage → 0
Other than above 0
16 B Ground — — 0
17 RIgnition switch
(ON or START)InputIgnition switch
(ON or START position)Battery voltage
18 SBSoft top switch
(OPEN) signalInputSoft top switch
open operate0
Other than above 5
19 R/WSoft top switch
(CLOSE) signalInputSoft top switch
close operate0
Other than above 5
20 W/BRoof full close detection switch
signalInput OP8 5 → 0
21 W/LRoof full open detection switch
signalInput OP11 5 → 0
22 W/RRoll bar interference prevention
switch signalInput OP9 5 → 0
PKIA1935E

SOFT TOP
RF-35
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
OPEN → CLOSE OPERATION
The operation chart for roof position. Refer to RF-21, "State Chart" .
48 Y/BStorage lid actuator LH
(CLOSE) signalOutputOP11 → OP12 0 → Battery voltage → 0
Other than above 0 Te r m i -
nal No.Wire
colorDescription
Condition
(Roof position: OP)Value (V)
(Approx.)
Signal nameInput/
Output
Te r m i -
nal No.Wire
colorDescription
Condition
(Roof position: CL)Va l u e ( V )
(Approx.)
Signal name Input/
Output
1 W/R Battery power supply Input — Battery voltage
3RRoof actuator RH
(OPEN) signalOutput — 0
4 G/R5th bow closure motor
(CLOSE) signalOutputCL10 0 → Battery voltage → 0
Other than above 0
5R/BStorage lid actuator RH
(OPEN) signalOutputCL2 → CL3
0 → Battery voltage → 0
CL8
Other than above 0
6 R 5th bow unlock actuator signal Output — 0
7 B Ground — — 0
8 W/R Battery power supply Input — Battery voltage
10 YRoof actuator RH
(CLOSE) signalOutputCL3 → CL6 0 → Battery voltage → 0
Other than above 0
12 G/Y5th bow closure motor
(OPEN) signalOutput — 0
13 L/RStorage lid actuator RH
(CLOSE) signalOutputCL7 → CL8 0 → Battery voltage → 0
Other than above 0
14 W Speed signal (8 pulse)Input/
OutputSpeed meter operate
[When vehicle speed is
Approx. 40 km/h (25 MPH)]
15 ORStorage lid unlock actuator LH
and RH signalOutputCL1 → CL2 0 → Battery voltage → 0
Other than above 0
16 B Ground — — 0
17 RIgnition switch
(ON or START)InputIgnition switch
(ON or START position)Battery voltage
18 SBSoft top switch
(OPEN) signalInputSoft top switch
open operate0
Other than above 5
19 R/WSoft top switch
(CLOSE) signalInputSoft top switch
close operate0
Other than above 5
20 W/BRoof full close detection
switch signalInput CL6 0 → 5
21 W/LRoof full open detection switch
signalInput CL3 0 → 5
PKIA1935E

RF-76
SOFT TOP
Revision: 2006 November2007 350Z
4. CHECK SOFT TOP CONTROL UNIT OUTPUT SIGNAL
1. Connect soft top control unit connector.
2. Start engine.
3. Check voltage between soft top control unit connector B67 ter-
minal 29 and ground.
OK or NG
OK >> Replace soft top lock switch (5th bow lock assembly in
storage lid).
NG >> Replace soft top control unit.
Check 5th Bow Closure MotorNIS0007D
1. 5TH BOW CLOSURE MOTOR INPUT SIGNAL
1. Start engine.
2. Operate soft top switch CLOSE, check voltage between 5th bow closure motor connector and ground.
OK or NG
OK >> Replace 5th bow closure motor.
NG >> GO TO 2.
2. CHECK 5TH BOW CLOSURE MOTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and 5th bow closure motor connector.
3. Check continuity between soft top control unit connector B66
terminal 4, 12 and 5th bow closure motor connector T204 termi-
nal 1, 2.
4. Check continuity between soft top control unit connector B66
terminal 4, 12 and ground.
OK or NG
OK >> Replace soft top control unit.
NG >> Repair or replace harness.29 (R/Y) - Ground : Approx. 5V
PIIA7936E
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
T204 1 (W) Ground CL9 → CL10 0 → Battery voltage → 0
PIIA7939E
4 (G/R) - 1 (W) : Continuity should exist.
12 (G/Y) - 2 (G) : Continuity should exist.
4 (G/R) - Ground : Continuity should not exist.
12 (G/Y) - Ground : Continuity should not exist.
PIIA7940E