2007 NISSAN 350Z door lock

RF-1
ROOF
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION RF
A
B
RF
Revision: 2006 November2007 350Z
ROOF
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Battery Service ................................ 3
Precautions .............................................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
SOFT TOP .................................................................11
Component Parts and Harness Connector Location .... 11
System Description ................................................ 12
CONDITIONS FOR OPERATION ....................... 13
CONDITIONS FOR STOPPING OPERATION .... 13
OUTLINE OF OPERATION ................................. 13
OPERATION: FULL CLOSE → FULL OPEN ...... 13
OPERATION: FULL OPEN → FULL CLOSE ...... 16
Operation Chart ...................................................... 19
CLOSE → OPEN ................................................ 19
OPEN → CLOSE ................................................ 21
Indicator Lamp ....................................................... 23
Schematic .............................................................. 24Wiring Diagram — F/ROOF — ............................... 25
Terminal and Reference Value of Soft Top Control
Unit ......................................................................... 33
CLOSE → OPEN OPERATION ........................... 33
OPEN → CLOSE OPERATION ........................... 35
Work Flow ............................................................... 37
Trouble Diagnosis Chart by Symptom .................... 37
(CLOSE → OPEN) .............................................. 37
(OPEN → CLOSE) .............................................. 38
Check Soft Top Control Unit Power Supply (OP, CL) ... 40
Check Soft Top Switch (OPEN) .............................. 40
Check Soft Top Switch (CLOSE) ............................ 42
Check 5th Bow Unlock Actuator (Open Operate) ... 44
Check 5th Bow Half-Latch Switch (Open Operate) ... 44
Check 5th Bow Actuator (Open Operate) ............... 46
Check 5th Bow Full Close Detection Switch (Open
Operate) ................................................................. 46
Check 5th Bow Full Open Detection Switch (Open
Operate) ................................................................. 48
Check Storage Lid Unlock Actuator (Open Operate) ... 49
Check Storage Lid Full Close Detection Switch
(Open Operate) ...................................................... 50
Check Storage Lid Actuator (Open Operate) .......... 52
Check Storage Lid Full Open Detection Switch
(Open Operate) ...................................................... 53
Check Roof Actuator (Open Operate) .................... 55
Check Roll Bar Interference Prevention Switch
(Open Operate) ...................................................... 56
Check Body Interference Prevention Switch (Open
Operate) ................................................................. 57
Check Roof Full Open Detection Switch (Open
Operate) ................................................................. 58
Check Storage Lid Unlock Actuator (Close Operate) ... 59
Check Storage Lid Full Close Detection Switch
(Close Operate) ...................................................... 60
Check Storage Lid Actuator (Close Operate) ......... 62
Check Storage Lid Full Open Detection Switch
(Close Operate) ...................................................... 63
Check Body Interference Prevention Switch (Close
Operate) ................................................................. 65

RF-2Revision: 2006 November2007 350Z Check Roof Actuator (Close Operate) .................... 66
Check Roof Full Close Detection Switch ................ 67
Check 5th Bow Actuator (Close Operate) .............. 69
Check 5th Bow Full Close Detection Switch (Close
Operate) ................................................................. 69
Check 5th Bow Full Open Detection Switch (Close
Operate) ................................................................. 71
Check 5th Bow Half-Latch Switch (Close Operate) ... 72
Check 5th Bow Full-Latch Switch ........................... 73
Check 5th Bow Ending Switch ................................ 75
Check 5th Bow Closure Motor ................................ 76
Check Soft Top Front Lock Switch .......................... 77
Check Operation Permission Condition .................. 78
Check Each Switch Condition (Open Operate) ...... 80
Check Each Switch Condition (Close Operate) ...... 81
Check Power Window Down Request Signal ......... 81
Check Power Window Harness .............................. 82
Check Passenger Side Seat Operate Signal 1 ....... 82
Check Passenger Side Seat Operate Signal 2 ....... 83
Check Passenger Side Seat Operate Signal 3 ....... 83
Check Seat Back Position Signal ........................... 83
Check Speed Signal Circuit .................................... 84
Check Indicator Lamp Circuit ................................. 85
Removal and Installation of Soft Top Control Unit ... 86
REMOVAL ........................................................... 86
INSTALLATION .................................................... 86
Component Parts Drawing ...................................... 87
Removal and Installation of Soft Top Assembly ...... 88
REMOVAL ........................................................... 88
INSTALLATION .................................................... 89
Removal and Installation of Soft Top Cover ............ 90
REMOVAL ........................................................... 90
INSTALLATION .................................................... 97
Removal and Installation of Switches ...................107
REMOVAL .........................................................107
INSTALLATION ..................................................107
Removal and Installation of Roof Actuator ...........108
REMOVAL .........................................................108
INSTALLATION ..................................................108
Removal and Installation of 5th Bow Drive Unit ....108REMOVAL ..........................................................108
INSTALLATION .................................................. 111
Removal and Installation of Front Lock .................115
REMOVAL ..........................................................115
INSTALLATION ..................................................115
INSPECTION AND ADJUSTMENT ...................115
Repairing Method for Water Leakage Around Doors .116
WATER LEAKAGE FROM A ..............................116
WATER LEAKAGE FROM B ..............................117
WATER LEAKAGE FROM C .............................117
WATER LEAKAGE FROM D .............................118
WATER LEAKAGE FROM E ..............................118
WATER LEAKAGE TEST ..................................119
Correspondence in Emergency ............................120
MANUAL OPERATION (SOFT TOP FULLY
OPEN
FULLY CLOSE) ..................................120
MANUAL OPERATION (SOFT TOP FULLY
CLOSE
FULLY OPEN) ..................................121
STORAGE LID .........................................................123
Removal and Installation of Storage Lid Assembly .123
REMOVAL ..........................................................123
INSTALLATION ..................................................123
Removal and Installation of Storage Lid Inside Unit .124
REMOVAL ..........................................................124
INSTALLATION ..................................................125
Removal and Installation of Storage Lid Actuator .126
REMOVAL ..........................................................126
INSTALLATION ..................................................126
Removal and Installation of Storage Room Finisher .126
REMOVAL ..........................................................126
INSTALLATION ..................................................127
Removal and Installation of Storage Outer Protector .127
Adjustment of Storage Lid .....................................128
ADJUSTMENT IN FULLY CLOSED POSITION .128
ADJUSTMENT IN FULLY OPENED POSITION .129
Removal and Installation of Storage Lid Striker Lock
& Storage Lid Emergency Opener Cable ..............130
REMOVAL ..........................................................130
INSTALLATION ..................................................130

SQUEAK AND RATTLE TROUBLE DIAGNOSES
RF-5
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
SQUEAK AND RATTLE TROUBLE DIAGNOSESPFP:00000
Work FlowNIS00298
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer's comments; refer to RF-9, "
Diagnostic Worksheet" . This information is necessary to duplicate the
conditions that exist when the noise occurs.

The customer may not be able to provide a detailed description or the location of the noise. Attempt to
obtain all the facts and conditions that exist when the noise occurs (or does not occur).

If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer
is concerned about. This can be accomplished by test driving the vehicle with the customer.

After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.

Squeak —(Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard sur-
faces=higher pitch noise/softer surfaces=lower pitch noises/edge to surface=chirping

Creak—(Like walking on an old wooden floor)
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch
dependent on materials/often brought on by activity.

Rattle—(Like shaking a baby rattle)
Rattle characteristics include the fast repeated contact/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.

Knock —(Like a knock on a door)
Knock characteristics include hollow sounding/sometimes repeating/often brought on by driver action.

Tick—(Like a clock second hand)
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.

Thump—(Heavy, muffled knock noise)
Thump characteristics include softer knock/dead sound often brought on by activity.

Buzz—(Like a bumble bee)
Buzz characteristics include high frequency rattle/firm contact.

Often the degree of acceptable noise level will vary depending upon the person. A noise that you may
judge as acceptable may be very irritating to the customer.

Weather conditions, especially humidity and temperature, may have a great effect on noise level.
SBT842

RF-6
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2006 November2007 350Z
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following:
1) Close a door.
2) Tap or push/pull around the area where the noise appears to be coming from.
3) Rev the engine.
4) Use a floor jack to recreate vehicle “twist”.
5) At idle, apply engine load (electrical load, half-clutch on M/T models, drive position on A/T models).
6) Raise the vehicle on a hoist and hit a tire with a rubber hammer.

Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.

If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the
vehicle body.
CHECK RELATED SERVICE BULLETINS
After verifying the customer concern or symptom, check ASIST for Technical Service Bulletins (TSBs) related
to that concern or symptom.
If a TSB relates to the symptom, follow the procedure to repair the noise.
LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE
1. Narrow down the noise to a general area. To help pinpoint the source of the noise, use a listening tool
(Chassis Ear: J-39570, Engine Ear and mechanics stethoscope).
2. Narrow down the noise to a more specific area and identify the cause of the noise by:

removing the components in the area that you suspect the noise is coming from.
Do not use too much force when removing clips and fasteners, otherwise clips and fastener can be broken
or lost during the repair, resulting in the creation of new noise.

tapping or pushing/pulling the component that you suspect is causing the noise.
Do not tap or push/pull the component with excessive force, otherwise the noise will be eliminated only
temporarily.

feeling for a vibration with your hand by touching the component(s) that you suspect is (are) causing the
noise.

placing a piece of paper between components that you suspect are causing the noise.

looking for loose components and contact marks.
Refer to RF-7, "
Generic Squeak and Rattle Troubleshooting" .
REPAIR THE CAUSE

If the cause is a loose component, tighten the component securely.

If the cause is insufficient clearance between components:
–separate components by repositioning or loosening and retightening the component, if possible.
–insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape or ure-
thane tape. A Nissan Squeak and Rattle Kit (J-43980) is available through your authorized Nissan Parts
Department.
CAUTION:
Do not use excessive force as many components are constructed of plastic and may be damaged.
NOTE:
Always check with the Parts Department for the latest parts information.
The following materials are contained in the Nissan Squeak and Rattle Kit (J-43980). Each item can be
ordered separately as needed.
URETHANE PADS [1.5 mm (0.059 in) thick]
Insulates connectors, harness, etc.
76268-9E005: 100×135 mm (3.94×5.31 in)/76884-71L01: 60×85 mm (2.36×3.35 in)/76884-
71L02: 15×25 mm (0.59×0.98 in)
INSULATOR (Foam blocks)
Insulates components from contact. Can be used to fill space behind a panel.
73982-9E000: 45 mm (1.77 in) thick, 50×50 mm (1.97×1.97 in)/73982-
50Y00: 10 mm (0.39 in) thick, 50×50 mm (1.97×1.97 in)

SQUEAK AND RATTLE TROUBLE DIAGNOSES
RF-7
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
INSULATOR (Light foam block)
80845-71L00: 30 mm (1.18 in) thick, 30×50 mm (1.18×1.97 in)
FELT CLOTHTAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
68370-4B000: 15×25 mm (0.59×0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll
The following materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in place of UHMW tape that will be visible or not fit. Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle TroubleshootingNIS00299
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. The cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by
applying felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate
wiring harness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you
will not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the Nissan Squeak and Rattle Kit (J-43980) to repair the noise.

RF-106
SOFT TOP
Revision: 2006 November2007 350Z
28. Install A link weather strip.
29. Install front lock finisher and welt after closing soft top.
30. Connect defogger harnesses at rear window.
31. Install 5th bow operating strut rods (RH/LH).
32. Install roof actuator (RH/LH). Refer to RF-108, "
Removal and Installation of Roof Actuator" .
33. Install soft top assembly to vehicle. Refer to RF-88, "
Removal and Installation of Soft Top Assembly" .
34. Check soft top open/close operation.
35. Check door glass contact. Refer to GW-53, "
FITTING INSPECTION" .
36. Check for water leakage. Refer to RF-116, "
Repairing Method for Water Leakage Around Doors" .
NOTE:
If there are wrinkles on the soft top cover, use a hair dryer to warm up the wrinkled area. Apply warm air from
the hair dryer keeping the distance by 150 - 200 mm (5.9 - 7.8 in) and move the dryer to gently warm up soft
top cover, for about 5 - 10 minutes until the wrinkle seems to be gone. Not to heat up soft top cover to much.
PIIB1318E