SOFT TOP
RF-37
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Work FlowNIS0006I
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to RF-12, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to RF-37,
"Trouble Diagnosis Chart by Symptom" .
4. Does soft top system operate normally? If Yes, GO TO 5. If No, GO TO 3.
5. INSPECTION END.
Trouble Diagnosis Chart by SymptomNIS0006J
(CLOSE → OPEN)
The operation chart for roof position. Refer to RF-19, "State Chart" .
48 Y/BStorage lid actuator LH
(CLOSE) signalOutputCL7 → CL8 0 → Battery voltage → 0
Other than above 0 Te r m i -
nal No.Wire
colorDescription
Condition
(Roof position: CL)Va l u e ( V )
(Approx.)
Signal name Input/
Output
Symptom Diagnostic procedure and repair order Roof position Refer to page
Roof does not operate1. Check soft top control unit power supply OP1RF-40
2. Check soft top switch (Open) OP1RF-40
3. Check operation permission condition OP1RF-78
4. Check each switch condition (Open operate) Full closeRF-80
5. Check seat back position signal OP1RF-83
6. Check 5th bow unlock actuator (Open operate) OP2RF-44
7. Check 5th bow half-latch switch (Open operate) OP2RF-44
8. Check 5th bow actuator (Open operate) OP3RF-46
5th bow operation stops at full
open position1. Check 5th bow full close detection switch
(Open operate)OP4RF-46
2. Check 5th bow full open detection switch
(Open operate)OP5RF-48
3. Check storage lid unlock actuator
(Open operate)OP5RF-49
4. Check storage lid full close detection switch (LH
and RH) (Open operate)OP5.6RF-50
5. Check storage lid actuator (Open operate) OP6RF-52
Storage lid operation stops at
full open positionCheck storage lid full open detection switch (Open
operate)OP7RF-53
Roof does not operate Check roof actuator (Open operate) OP8RF-55
Roof stops on the wayCheck roll bar interference prevention switch
(Open operate)OP8RF-56
Storage lid operation stops at
full open position after the roof
is stored.1. Check body interference prevention switch
(Open operate)OP10RF-57
2. Check roof full open detection switch OP10RF-58
Passenger side seat back does
not operate.1. Check passenger side seat cancel switch OP1SE-52
2. Check passenger side seat operate signal 1 OP1RF-82
Passenger side seat bock does
not return to former stateCheck passenger side seat operate signal 2 OP10RF-83
Power window down does
not operate.Check power window harness OP1RF-82
RF-80
SOFT TOP
Revision: 2006 November2007 350Z
5. CHECK BRAKE PEDAL SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and stop lamp switch connector.
3. Continuity between soft top control unit connector B68 terminal
38 and stop lamp switch connector E111 terminal 4.
4. Continuity between soft top control unit connector B68 terminal
38 and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair or replace harness.
6. CHECK STOP LAMP SWITCH
Continuity between stop lamp switch connector E111 terminal 3 and 4.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace stop lamp switch.
Check Each Switch Condition (Open Operate)NIS0007F
1. CHECK EACH SWITCH SIGNAL
1. Start engine.
2. Check voltage between soft top control unit connector and ground.
OK or NG
OK >> Each switch condition is OK.
NG >> Check malfunction switch.38 (W) - 4 (P/L) : Continuity should exist.
38 (W) - Ground : Continuity should not exist.
PIIB7357E
Connector Terminal Brake pedal condition Continuity
E 111 3 4Depressed Yes
Released No
PIIB7358E
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B6720 (W/B)
Ground Full closed 5 21 (W/L)
22 (W/R)
24 (G)
25 (L/Y)
26 (LG)
27 (GY)
32 (W)
33 (BR)
PIIA7949E
