2007 NISSAN 350Z battery location

RF-1
ROOF
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION RF
A
B
RF
Revision: 2006 November2007 350Z
ROOF
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Battery Service ................................ 3
Precautions .............................................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
SOFT TOP .................................................................11
Component Parts and Harness Connector Location .... 11
System Description ................................................ 12
CONDITIONS FOR OPERATION ....................... 13
CONDITIONS FOR STOPPING OPERATION .... 13
OUTLINE OF OPERATION ................................. 13
OPERATION: FULL CLOSE → FULL OPEN ...... 13
OPERATION: FULL OPEN → FULL CLOSE ...... 16
Operation Chart ...................................................... 19
CLOSE → OPEN ................................................ 19
OPEN → CLOSE ................................................ 21
Indicator Lamp ....................................................... 23
Schematic .............................................................. 24Wiring Diagram — F/ROOF — ............................... 25
Terminal and Reference Value of Soft Top Control
Unit ......................................................................... 33
CLOSE → OPEN OPERATION ........................... 33
OPEN → CLOSE OPERATION ........................... 35
Work Flow ............................................................... 37
Trouble Diagnosis Chart by Symptom .................... 37
(CLOSE → OPEN) .............................................. 37
(OPEN → CLOSE) .............................................. 38
Check Soft Top Control Unit Power Supply (OP, CL) ... 40
Check Soft Top Switch (OPEN) .............................. 40
Check Soft Top Switch (CLOSE) ............................ 42
Check 5th Bow Unlock Actuator (Open Operate) ... 44
Check 5th Bow Half-Latch Switch (Open Operate) ... 44
Check 5th Bow Actuator (Open Operate) ............... 46
Check 5th Bow Full Close Detection Switch (Open
Operate) ................................................................. 46
Check 5th Bow Full Open Detection Switch (Open
Operate) ................................................................. 48
Check Storage Lid Unlock Actuator (Open Operate) ... 49
Check Storage Lid Full Close Detection Switch
(Open Operate) ...................................................... 50
Check Storage Lid Actuator (Open Operate) .......... 52
Check Storage Lid Full Open Detection Switch
(Open Operate) ...................................................... 53
Check Roof Actuator (Open Operate) .................... 55
Check Roll Bar Interference Prevention Switch
(Open Operate) ...................................................... 56
Check Body Interference Prevention Switch (Open
Operate) ................................................................. 57
Check Roof Full Open Detection Switch (Open
Operate) ................................................................. 58
Check Storage Lid Unlock Actuator (Close Operate) ... 59
Check Storage Lid Full Close Detection Switch
(Close Operate) ...................................................... 60
Check Storage Lid Actuator (Close Operate) ......... 62
Check Storage Lid Full Open Detection Switch
(Close Operate) ...................................................... 63
Check Body Interference Prevention Switch (Close
Operate) ................................................................. 65

RF-40
SOFT TOP
Revision: 2006 November2007 350Z
Check Soft Top Control Unit Power Supply (OP, CL)NIS0006K
1. CHECK FUSE

Check 10A fuse [No.12, located in the fuse block (J/B)]

Check 40A fusible link (letter G located in the fuse and fusible link box.)
NOTE:
Refer to RF-11, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-4, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Start engine.
2. Check voltage between soft top control unit connector B66, 67
terminal 1, 8, 17 and ground.
OK or NG
OK >> GO TO 3.
NG >> Check soft top control unit power supply circuit for open
or short.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit connector.
3. Check continuity between soft top control unit connector B66
terminal 7, 16 and ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Check soft top control unit ground circuit for open or
short.
Check Soft Top Switch (OPEN)NIS0006L
1. CHECK SOFT TOP OPEN SWITCH SIGNAL
1. Start engine.
2. Check soft top control unit connector and ground.
OK or NG
OK >> Soft top switch (OPEN) is OK.
NG >> GO TO 2.1 (W/R) - Ground : Battery voltage
8 (W/R) - Ground : Battery voltage
17 (R) - Ground : Battery voltage
PIIA7886E
7 (B) - Ground : Continuity should exist.
16 (B) - Ground : Continuity should exist.
PIIA7887E
ConnectorTerminal (Wire color)
Soft top switch
ConditionVoltage (V)
(Approx.)
(+) (-)
B67 18 (SB) GroundOPEN 0
Other than above 5
PIIA7888E

SOFT TOP
RF-79
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
2. CHECK VEHICLE SPEED SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and unified meter and A/C amp connector.
3. Check the following.
–Continuity between soft top control unit connector B66 terminal
14 and unified meter and A/C amp connector M49 terminal 26.
–Continuity between soft top control unit connector B66 terminal
14 and ground.
4. Check the following.
–Continuity between soft top control unit connector B67 terminal
23 and unified meter and A/C amp connector M49 terminal 34.
–Continuity between soft top control unit connector B67 terminal
23 and ground.
OK or NG
OK >> Check unified meter and A/C amp. Refer to DI-44, "Sys-
tem Description" .
NG >> Repair or replace harness.
3. CHECK FUSE

Check 10A fuse [No.20, located in fuse block (J/B)].
NOTE:
Refer to RF-11, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 4.
NG >> If fuse blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-4, "
POWER SUPPLY ROUTING CIRCUIT" .
4. CHECK BRAKE PEDAL SIGNAL
Check voltage between soft top control unit connector and ground.
OK or NG
OK >> Stop lamp switch is OK.
NG >> GO TO 5.14 (W) - 26 (W) : Continuity should exist.
14 (W) - Ground : Continuity should not exist.
PIIA7942E
23 (W/G) - 34 (L) : Continuity should exist.
23 (W/G) - Ground : Continuity should not exist.
PIIA7943E
ConnectorTerminal (Wire color)
Brake pedal condi-
tionVoltage (V)
(Approx.)
(+) (-)
B68 38 (W) GroundDepressed Battery voltage
Released 0
PIIA7944E

SOFT TOP
RF-85
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
2. CHECK VEHICLE SPEED SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and unified meter and A/C amp connector.
3. Check the following.
–Continuity between soft top control unit connector B66 terminal
14 and unified meter and A/C amp connector M49 terminal 26.
–Continuity between soft top control unit connector B66 terminal
14 and ground.
4. Check the following.
–Continuity between soft top control unit connector B67 terminal
23 and unified meter and A/C amp connector M49 terminal 34.
–Continuity between soft top control unit connector B67 terminal
23 and ground.
OK or NG
OK >> Check unified meter and A/C amp. Refer to DI-44, "Sys-
tem Description" .
NG >> Repair or replace harness.
Check Indicator Lamp CircuitNIS0007O
1. CHECK FUSE

Check 10A fuse [No.14, located in fuse block (J/B)]
NOTE:
Refer to RF-11, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-4, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK INDICATOR LAMP SIGNAL
1. Start engine.
2. Soft top switch operate, check voltage between soft top control unit connector and ground.
OK or NG
OK >> Check the condition of the harness and the connector.
NG - 1 >> If battery voltage: Replace soft top control unit.
NG - 2 >> If 0V: GO TO 3.14 (W) - 26 (W) : Continuity should exist.
14 (W) - Ground : Continuity should not exist.
PIIA7942E
23 (W/G) - 34 (L) : Continuity should exist.
23 (W/G) - Ground : Continuity should not exist.
PIIA7943E
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B67 35 (Y) GroundFull open or full close Battery voltage
Other than above 0
PIIB0835E