2007 KIA CARNIVAL service

2007 > 2.7L V6 GASOLINE >
REMOVAL(INCLUDING FUEL FILTER AND FUEL PRESSURE REGULATOR)
1.Preparation
(1) Remove the 2nd seat(s) (Refer to "BD" group in this WORKSHOP MANUAL).
(2) Remove the striker cover (A).
(3) Remove the Service Cover (B).
(4)Disconnect the Fuel Pump Connector (A).
(5)Start the engine and wait until fuel in fuel line is exhausted.
(6) After the engine stalls, turn the ignition switch OFF.
2. After disconnecting the fuel feed quick connector (A) and unscrewing the the eight screws (B), remove the fuel
pump assembly.

fluctuated even though turns on or off the input signal. The electrical ‘time constant’ is much more fast than one of
mechanical so the frequency of VFS is extremely higher than the conventional PWM type.
Characteristics of Bosch VFS:
Supply pressure : 700~1600kPa
Control pressure: typically 600~0 kPa
Current range: typically 0~1,000 mA
Dither frequency: Up to 600 Hz
Dimension: 32 mm protrusion reach 42 mm
The reducing pressure will be supplied to the ‘Supply’ port of the VFS valve on the above illustration to control the line
pressure.
Reducing pressure
Function
As same as one of Alpha or Beta automatic transaxle system, this reducing valve length can be adjusted by rotating
the screw on the picture. As you rotate the screw toward clockwise by 90°, the reducing pressure will increase about
1.0bar. However, the reducing pressure is used just as a ‘supply pressure’ for the solenoid valves (except
Low&Reverse, Reduction and Damper Clutch control solen), so this may not be handled to rotate in the field service
shop. VFS is operated based on the ‘supply pressure’ and it outputs the ‘control pressure’ to control the regulator
valve indirectly. While developing the VFS system, the line pressure was used as a ‘supply pressure’ for VFS and
other solenoid valves but it has been changed into additional ‘reducing pressure’ because the line pressure is variably
changed by VFS so the control pressure becomes unstable and some hydraulic pressure oscillation occurred. That is

DCC Solenoid valveShort to B+
P0743P0743
Open or short to ground
1st speed asynchronous Synchronous error
0,11P0731
P0731
2nd speed asynchronous Synchronous error P0732P0732
3rd speed asynchronous Synchronous error P0733P0733
4th speed asynchronous Synchronous error P0734P0734
Reverse speed asynchronous Synchronous error ――
CAN No ID from ECM
2,3,6,7,9,10,11―
P1604
CAN BUS off ―P1603
Damper clutch Abnormal system 7P0741P0741
A/T relay Short to ground or open 0,11P0885P0885
Inhibitor switch Short to ground or open
―P0707
P0707
Short to B+ or short between switches P0708P0708
VFS Short to B+
11
―P0748
Short to ground 0,11
Open 11
CKP sensor Sensor errorNe=3,000rpm
7,9 ―
―
TPS sensor Sensor errorTPS=50Ë――
SERVICE DATA LIST(WITH SCAN TOOL)
No.ITEM NAME UNITDATA Data Description Failure
1 ENGINE RPM rpm700 rpmCurrent Engine rpm 0 rpm
2 VEHICLE SPEED km/h0km/hCurrent Vehicle speed 0km/h
3 THROTTLE
P.SENSOR %
12.5%Current TPS open angle 0%
4 INPUT SPEED(PG - A) rpm700 rpmInput speed rpm. Always output rpm
when turning start ON 0 rpm
5 OUTPUT SPEED(PG -
B) rpm
0 rpmOutput speed rpm. Always output
rpm when driving 0 rpm
6 DCC(TCC) SOLENOID
DUTY %
0%Control 0%
→ 100% when
operating Damper Clutch
7 DAMPER CLUTCH
SLIP rpm
260 rpmCurrent Damper clutch slip ratio 0 rpm
8 LR SOLENOID DUTY %100%Control 100%
→ 0% when
operating brake 0%
9 UD SOLENOID DUTY %100%Control 100%
→ 0% when
operating clutch 0%
10 2ND SOLENOID DUTY %100%Control 100%
→ 0% when
operating clutch 0%
11 OD SOLENOID DUTY %100%Control 100%
→ 0% when
operating clutch 0%
12 VFS SOLENOID DUTY Ë0~400Ë ―

2007 > 2.7L V6 GASOLINE >
SERVICE ADJUSTMENT PROCEDURE
Automatic transaxle fluid
INSPECTION 1. Drive the vehicle until the fluid reaches normal operating temperature [70~80°C].
2. Place the vehicle on a level surface.
3. Move the selector lever through all gear positions. This will fill the torque converter and the hudraulic system with
fluid and move the selector lever to the "N" (Neutral) or "P"(Park) position.
4. Before removing the oil level gauge, wipe all contaminants from around the oil level gauge. Then take out the oil
level gauge and check the condition of the fluid.
If the fluid smells as if it is burning, it means that the fluid has been contaminated by fine particles from the
bushes and friction materials, a transaxle overhaul may be necessary.
5. Check that the fluid level is at the HOT mark on the oil level gauge. If the fluid level is low, add automatic transaxle
fluid until the level reaches the "HOT" mark.
Auto transaxle fluid:
DIAMOND ATF SP - III, SK ATF SP - III
Quantity : 8.5ℓ (9.0 US qt, 7.5 lmp.qt)
Low fluid level can cause a variety of a abnormal conditions because it allows the pump to take in air along
with fluid. Air trapped in the hydraulic system forms bubbles, which are compressable. Therefore, pressures
will be erratic, causing delayed shifting ,slipping clutches and brakes, etc. Improper filling can also raise fluid
level too high. When the transaxle has too much fluid, gears churn up foam and acuise the same conditions
which occur with low fluid level, resulting in accelerated deterioration of automatic transaxle fluid. In either
case, air bubbles can cause overheating, and fluid oxidation, which can interfere with normal valve, clutch, and
brake operation. Foaming can also result in fluid escaping from the transaxle vent where it may be mistaken
for a leak.
6. Insert the oil level gauge(A) securely.
When new, automatic transmission fluid should be red. The red dye is added so the assembly plant can
identify it as transmission fluid and distinguish it from engine oil or antifreeze. The red dye, which is not an
indicator of fluid quality, is not permanent. As the vehicle is driven the transmission fluid will begin to look
darker. The color may eventually appear light brown.

25.Install the air cleaner assembly (B) by tightening the two mounting bolts (A).
26.Reassemble the air cleaner filter, install the air cleaner upper body (B) and connect the air flow sensor connector
(A).
27.Install the battery (A).
28.Refill the transaxle fluid. (see 'Service adjustment procedure')
29. Refill the power steering fluid. (see 'ST' group)

2007 > 2.7L V6 GASOLINE >
SPECIFICATION
Engine type µ 2.7
Manual transaxle type M5GF2
Gear ratio 1st 3.615
2nd 1.931
3rd 1.969
4th 1.273
5th 0.974
Reverse 3.416
Final gear ratio 5.071
3.737
T/M oil capacity(ℓ) ※ 1.9 liter (2.0077US qt, 1.6718mp qt)
※ The quantity in the chart above is for the reference. The actual filling quantity of the automatic transaxle fluid must
be set according to 'INSPECTION' or 'REPLACEMENT' procedure of the automatic transaxle fluid.
Recommended transaxle oil SAE75W/85 or API GL - 4
Check&Replenishment Every one year or every 100,000km
Replacement Private useNormal use
No service required
Severe use( ※)
Every 100,000 Km
Business use
※ Severe use(marked '※') is defined as:
1. Driving on rough road(bumpy road, gravel road, snowy road, unpaved road etc.).
2. Driving on mountain road, ascent/descent.
3. Repetition of short distance driving.
4. More than 50% operation in heavy city traffic during hot weather above 32°C(89.6°F).
5. Police car, Taxi, Commercial type operation or trailer towing, etc.
TIGHTENING TORQUE
Item Nmkgf.m lb- ft
Oil drain plug 30~353.0~3.521.7~25.3
Oil filler plug 30~353.0~3.521.7~25.3
Back up lamp switch 30~353.0~3.521.7~25.3
Control shaft assembly 10~121.0~1.2 7.2~8.7
Select lever 43~554.3~5.531.1~39.8
Shift link assembly 43~554.3~5.531.1~39.8
Transaxle mounting bracket assembly 65~856.5~8.547.0~61.5
Transaxle and enging mounting bolt 65~856.5~8.547.0~61.5
SERVICE STANDARD Item Specification [mm(inch)]

2007 > 2.7L V6 GASOLINE >
SERVICE ADJUSTMENT PROCEDURE
Transmission oil inspection and replacement
1. After parking the vehicle on a plain, stop the engine.
2. After removing the oil filler plug and washer, inspect the manual transaxle fluid condition and quantity.
3. If the manual transaxle fluid is contaminated, drain it out by removing the oil drain plug.
4. Tighten the new oil drain plug and feed manual transaxle fluid to a proper level.
TORQUE:
29.4~34.4 Nm(3.0~3.5kgf.m, 21.7~25.3lb - ft)
Oil type: SAE75W/85
Oil quantity:
1.9 liter(2.0077 US qt, 1.6718 lmp qt)
5. Retighten the oil filler plug with a new washer.
TORQUE:
29.4~34.4 Nm(3.0~3.5kgf.m, 21.7~25.3lb - ft)
Back up lamp switch inspection
1.Disconnect the back up lamp switch connector(B).
2.Inspect the continuity of the switch. When the shift lever is located in reverse range, it should be applied an electric
current.
3. Replace the back up lamp switch, if necessary.
TORQUE:
29.4~34.4 Nm(3.0~3.5kgf.m, 21.7~25.3lb - ft)

2007 > 2.7L V6 GASOLINE >
SPECIAL SERVICE TOOLS
Tool (Number and Name) IllustrationUse
09568 - 4A000
Ball joint remover
Removal of Ball joint
(Front upper arm/lower arm, & Rear
upper arm)
09532 - 11600
Preload socket
Measurement of the front lower arm
ball joint starting torque.
(Use with torque wrench)
09546 - 26000
Strut spring compressor
Compression of the coil spring
09214 - 32000
Mount bushing remover and installer
Removal & installation of lower arm
bushing(G)
(Use with 09216 - 21100)
09216 - 21100
Mount bushing remover and installer
Removal & installation of lower arm
bushing(G)
(Use with 09216 - 32000)
09216 - 21600
Mount bushing remover and installer
arbor
Removal and installation of trailing
arm bushing
(Use with 09552 - 38100)
09552 - 38100 Removal and installation of the rear