2007 ISUZU KB P190 BATTERY

8A-430 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION


This illustration is based on RHD RTW 780SH002601






DRIVER’S SIDE POWER WINDOW &
DOOR LOCK SWITCH
(2 DOOR MODELS)
Removal
1. Disconnect the battery ground cable.
2. Remove the screw in the pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.



Installation
To install, follow the removal steps in the reverse order.



This illustration is based on RHD RTW 780SH002701






FRONT PASSENGER’S POWER WINDOW
SWITCH
(2 DOOR MODELS)
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in the pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.



Installation
To install, follow the removal steps in the reverse order.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-431

This illustration is based on RHD RTW 780SH002601
DRIVER’S SIDE POWER WINDOW &
DOOR LOCK SWITCH
(4 DOOR MODELS)
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.


Installation
To install, follow the removal steps in the reverse order.


This illustration is based on RHD RTW 780SH002701


FRONT PASSENGER’S POWER WINDOW
SWITCH
(4 DOOR MODELS)
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.



Installation
To install, follow the removal steps in the reverse order.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-432 ELECTRICAL-BODY AND CHASSIS


RTW 780SH002801


REAR POWER WINDOW & DOOR LOCK
SWITCH-LH & RH
Removal
1. Disconnect the battery ground cable.
2. Remove the screw in the pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.



Installation
To install, follow the removal steps in the reverse order.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-434 ELECTRICAL-BODY AND CHASSIS
INSPECTION AND REPAIR






B8
RTW 78ASH002901

Power Window Relay
Check continuity between the relay terminals.
2- 1........................ No continuity
(W hen battery voltage is applied between
3 and 4)
2- 1........................ Continuity





Harness side
D20 D5


Driver’s Side Power Window & Door Lock
Switch
1. Harness Side Connector Circuit
Disconnect the switch connector, and check voltage and continuity between the harness side connector terminals as
shown in the following table.

Terminal No. Wire
color Connecting to Check item Connectin
g terminal Check condition Standard
6 G/R Power window
relay Voltage 6-Ground Starter SW “ON” Approx.
12V
7 BR/R Power window
8 BR/W motor

3 B Ground Continuity 3-Ground - Continuity






Harness side
D10


Front Passenger’s Power Window Switch
1. Harness Side Connector Circuit
Disconnect the switch connector, and check voltage and continuity between the harness side connector terminals as
shown in the following table.

Continuity
-
7-8
Continuity

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-436 ELECTRICAL-BODY AND CHASSIS




Harness side
D5

Driver’s Side Power Window Motor
1. Driver’s Side Power Window & Door Lock Switch
Connector Circuit
Disconnect the switch connector, apply the battery voltage (12V) to the harness side connector terminals and check
operation.
Connecting terminals Operation
7 (BR/R) 8 (BR/W ) direction
- + DOW N
+ - UP




D1


2. Driver’s Side Power Window Motor Connector Circuit
Disconnect the switch connector, apply the battery voltage (12V) to the motor side connector terminals and check
operation.
Connecting terminals Operation
1 2 direction
+ - DOW N
- + UP


BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-437




Harness side
D10

Front Passenger’s Power Window Motor
1. Front Passenger’s Power Window Switch Connector
Circuit
Disconnect the motor connector, apply the battery voltage (12V) to the harness side connector terminals and check
operation.
Connecting terminals Operation
8 (BR/R) 7 (BR/W ) direction
- + DOW N
+ - UP



D6


2. Front Passenger’s Power Window Motor Connector
Circuit
Disconnect the switch connector, apply the battery voltage (12V) to the motor side connector terminals and check
operation.
Connecting terminals Operation
1 2 direction
+ - DOW N
- + UP


BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-438 ELECTRICAL-BODY AND CHASSIS




Harness side
D12

Rear Passenger’s Power Window Motor-LH
1. Rear Power Window Switch-LH Connector Circuit
Disconnect the motor connector, apply the battery voltage (12V) to the harness side connector terminals and check
operation.
Connecting terminals Operation
8 (BR/R) 7 (BR/W ) direction
- + DOW N
+ - UP



D11


2. Rear Power Window Motor-LH Connector Circuit
Disconnect the switch connector, apply the battery voltage (12V) to the motor side connector terminals and check
operation.
Connecting terminals Operation
1 2 direction
+ - DOW N
- + UP


BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-439




Harness side
D16

Rear Power Window Motor-RH
1. Rear Power Window Switch-RH Connector Circuit
Disconnect the motor connector, apply the battery voltage (12V) to the harness side connector terminals and check
operation.
Connecting terminals Operation
8 (BR/R) 7 (BR/W ) direction
- + DOW N
+ - UP



D15


2. Rear Power Window Motor-RH Connector Circuit
Disconnect the switch connector, apply the battery voltage (12V) to the motor side connector terminals and check
operation.
Connecting terminals Operation
1 2 direction
+ - DOW N
- + UP



BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007