2007 ISUZU KB P190 BATTERY

ELECTRICAL-BODY AND CHASSIS 8A-273
TROUBLESHOOTING
WINDSHIELD WIPER
1. Wiper dose not operate at any switch position

Checkpoint Trouble Cause Countermeasure


Reinstall or replace the fuse
No. C9 (20A)

Poor fuse contact or blown

NG

Repair open circuit or
connector contact

1. W iper motor function when
connecting the motor
connector 3
C4 to the
battery (+) terminal, and 1
C4 to the (-) terminal
(Should the wiper motor
rotate at a low speed)
2. W iper motor function when connecting the motor
connector 2
C4 to the
battery (+) terminal, 1
C4 to the (-) terminal
(Should the wiper motor
rotate at a high speed)
Voltage between 3 B59 and
the ground (Should be battery
v oltage present)

Open circuit or poor connector
contact


Replace the wiper & washer
SW .

Continuity in the wiper &
washer SW .

SW . malfunction

NG
NG
OK
OK

Fuse No. C9 (20A)


Repair grounding point
contact
Grounding point
C2 (LHD),
C
C36 (RHD)


Poor grounding point contact

NG
OK
OK

Replace the wiper motor

W iper motor malfunction

NG

Repair open circuit or
connector contact

Continuity between 1
C4
and
C36 (RHD), C2 (LHD)


Open circuit or poor connector
contact

NG
OK



BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-274 ELECTRICAL-BODY AND CHASSIS
2. Wiper dose not operate at “ INT “ position

Checkpoint Trouble Cause Countermeasure


Replace the wiper & washer
SW .

SW . malfunction

NG


Repair grounding point contact

Grounding point
C36 (RHD),

C2 (LHD)


Poor grounding point contact


Repair open circuit or
connector contact

Voltage between the
intermittent relay harness side
connector terminal 4
C3
and the ground at the “INT”
position (Should be battery
voltage present)

Open circuit or poor connector
contact

NG
NG
OK
OK
Continuity between the wiper
& washer SW connector
terminals 4
B59 and 2 B59
at the “ INT “ position

Replace the intermittent relay

Intermittent relay function

Relay malfunction

NG
OK



3. Wiper does not operate at “LO” position



Replace the wiper motor

W iper motor function
1. Disconnect the wiper & washer SW . connector
2. Turn the starter SW . on
3. Short-circuit between the wiper & washer SW .
harness side connector terminal 3
B59 and
5
B59 .
4. Check to see if the wiper
motor rotates at a low
speed

W iper motor malfunction

NG

Replace the wiper & washer
SW .

W iper & washer SW . function

SW . malfunction

NG
OK


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-275
4. Wiper does not operate at “HI” position

Checkpoint Trouble Cause Countermeasure


Repair open circuit or
connector contact

Open circuit or poor connector
contact

NG


Replace the wiper motor

W iper motor function when
connecting the motor
connector 2
C4 to the
battery (+) terminal, and 1
C4 to the (-) terminal
(Should the wiper motor rotate
at a high speed)

W iper motor malfunction

NG
OK
Continuity between the wiper
& washer SW . connector
terminals 4
B59 at the “HI”
position

Repair open circuit or
connector contact

Continuity between 4
B59
and 2
C4


Open circuit or poor connector
contact

NG
OK



5. Rotation of the wiper motor does not stop


Replace the wiper & washer
SW .

SW . malfunction

NG

OK
Continuity in the wiper &
washer SW .


Replace the wiper motor

W iper motor function

W iper motor malfunction

NG



BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-276 ELECTRICAL-BODY AND CHASSIS
6. Auto-stop function of the wiper motor does not operate

Checkpoint Trouble Cause Countermeasure


Repair open circuit or
connector contact

Open circuit or poor connector
contact

NG

Repair open circuit or
connector contact

Open circuit or poor connector
contact

NG Continuity between the
intermittent relay harness side
connector 6
C3 and the
wiper motor harness side
connector 6
C4

Replace the intermittent relay

Relay malfunction

NG
Intermittent relay function


W iper motor function
1. Disconnect the wiper motor connector
2. Connect the motor connector 5
B59 to the
battery (+) terminal and
1
C4 to the (-) terminal,
and then change the
connection of the battery (+)
terminal to the connector
4
C4 while the motor
rotating at a low speed
3. Check to see if the wiper motor stops at the auto stop
position when connecting
the connector terminals
3
C4 and 1 C4 in this
condition
Continuity between the wiper
& washer SW . connector
terminals 5
B59 and 6 B59
at the “OFF” position
OK

Replace the wiper motor

W iper motor malfunction

NG
Repair an open circuit or a
poor connection of the
connectors between the fuse
No. C9 (20A) and 4
C4
Voltage between the wiper
motor harness side connector
terminal 4
C4 and the
ground (Should be battery
v oltage present)

Open circuit or poor connector
contact

NG
OK
OK
OK



BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-277
WASHER
1. Washer motor does not operate

Checkpoint Trouble Cause Countermeasure


Reinstall or replace the fuse
No. C9 (20A)

Poor fuse contact or blown

NG
Repair or an open circuit or a
poor connection of the
connectors between 2
C17
and 1
B59

Open circuit or poor connector
contact

NG Voltage between the washer
motor harness side connector
terminal 2
C17 and the
ground when the washer
button is depressed (Should
be battery v oltage present)

Repair grounding point
C36
contact

Poor grounding point contact

NG
Grounding point
C36


Replace the washer motor

Motor malfunction

NG
W asher motor function when
connecting the motor side
connector 2
C17 to the
battery (+) terminal, and the
connector 1
C17 to the (-)
terminal (Should the washer
motor rotate) OK

Repair open circuit or
connector contact

Open circuit or poor connector
contact

NG
Continuity between 1
C17
and
C36
OK

Continuity between the wiper
& washer SW . side connector
terminals 1
B59 and 7 B59
when the washer button is
depressed

Fuse No. C9 (20A)

OK

Replace the wiper & washer
SW .

SW . malfunction

NG
Repair or an open circuit or a
poor connection of the
connectors between the fuse
No. C-9 (20A) and 7
B59
Voltage between the wiper &
washer SW . harness side
connector terminal 7
B59
and the ground (Should be
battery v oltage preset)

Open circuit or poor connector
contact

NG
OK
OK
OK


BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-279
INSPECTION AND REPAIR





Switch side
B59


Control Switch Connections
Terminal
No.
SW position 6 3 5 4 2 7 1
Mist
Off
INT


Lo
Hi
Wash



Wiper Motor Inspection
Connector



Low Speed Inspection
1. Clamp the wiper motor in a vise.
The moving parts must be clear of the vise.
2. Connect the connector terminals to the battery.
Refer to the illustration.
3. Check the wiper motor low speed operation.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-280 ELECTRICAL-BODY AND CHASSIS

High Speed Inspection
1. Clamp the wiper motor in a vise.
The moving parts must be clear of the vise.
2. Connect the connector terminals to the battery.
Refer to the illustration.
3. Check the wiper motor high speed operation.


Auto-Stop Inspection
1. Clamp the wiper motor in a vise.
The moving parts must be clear of the vise.
2. Connect the connector terminals to the battery.
Refer to the illustration.
3. Check the wiper motor low speed operation.
4. Disconnect the positive battery terminal.
This will stop the motor.



5. Connect the connector terminals No. 3 and No. 6 with a
lead wire.
Refer to the illustration.
6. Reconnect the positive battery terminal to connecto
r
terminal No. 4.
This will restart the motor.
Refer to the illustration.
7. Check the auto-stop operation.







Washer Motor Inspection
1. Fill the washer tank with washing solution.
2. Disconnect the motor connector.
3. Apply battery voltage to the washer motor connector.
4. Check the washer motor operation.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-369
Low Fuel Indicator Light
1. Disconnect the fuel gauge unit wire connector.
2. Turn the key switch on. Check that the bulb lights.
If operation is not correct, remove and check the bulb or circuit.
or If check whether low fuel turns on fuel input (B-24) at the
time of open and key on.
∗ meter is check at low fuel



RTW 78ASH001501




Check level sensor operation
1. Remove the fuel gauge unit.
2. Apply battery voltage between terminal (B) and (C) through a 1.12 watt bulb. Check that the bulb lights.
Note:
It will take a short time for the bulb light.
3. Submerge the sensor in fuel. Check that the bulb goes out.
If operation is not correct, replace the fuel tank unit.

BRAKE SYSTEM WARNING LIGHT
The brake system warning light comes on while the parking
brake is set and the engine run position.

RTW 48AMH000101


Note:
The parking brake indicator light circuit is designed to
prevent driving of the vehicle with the parking brake on.
It does not indicate the condition of the parking brake
system.

The parking brake switch is in parallel with the brake fluid
switch.


The brake system warning light also comes on when reservoir
brake fluid level falls below the specified limit with the parking
brake released and the engine run position.

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007