2007 ISUZU KB P190 torque

2A-12 FRAME AND BUMPER






Important Operations - Installation
3. Nut • Tighten the fixing bolts to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
116 (11.8
/ 85)
















RTW 72AMH000201







2. Rear Bumper Assembly
1) Align the back bar to the frame (1) as follows:
• Face A (2) should be contacted with the upper face o
f
the frame
• Face B (3) should be contacted with the rear end o
f
the frame.
2) Tighten the 2 fixing bolts on the each side of back bar.

Torque N ⋅m (kgf ⋅m/lb ⋅ft)
150 (15.3
/ 111)

1. Rear Guard Assembly 1) Align the back bar to the frame (1) as follows:
• Face A (2) should be contacted with the upper face o
f
the frame
• Face B (3) should be contacted with the rear end o
f
the frame.
2) Tighten the 2 fixing bolts on the each side of back bar.

Torque N ⋅m (kgf ⋅m/lb ⋅ft)
150 (15.3
/ 111)




BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRAME AND BUMPER 2A-13
FRONT AIR DAM
REMOVAL AND INSTALLATION

RTW 72AMF000201

Removal Steps
1. Bolt
2. Front air dam

Installation Steps

2. Front air dam
1. Bolt






Important Operation - Removal
1. Bolt
Remove the 12 fixing bolts.

Important Operation - Installation
1. Bolt
Torque N ⋅m (kgf ⋅m/lb ⋅in)
3 (0.3 / 26)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

2B-4 SHEET METAL

2. Hood Hinge Bolt
• Tighten the engine hood hinge fixing bolts to the specified
torque.

Torque N ⋅m(kgf ⋅m/lb ⋅in)
10 (1.0 / 87)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

SHEET METAL 2B-7



• Clearance : 4.0 mm (0.16 in)
• Height (step) : Flushness
• Adjust clearance using the hinges on the engine hood.



RTW 72BSH000701







• Adjust height (step) using the hood rests (1).






Engine Hood Striker
• Apply a light coat of grease to the striker.



4. Hood Hinge Bolt
• Tighten the engine hood hinge fixing bolts to the specified
torque.

Torque N ⋅m(kgf ⋅m/lb ⋅in)
10 (1.0 / 87)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

2B-10 SHEET METAL

2. Hood Hinge Bolts
• Tighten the engine hood hinge fixing bolts to the specified
torque.

Torque N ⋅m(kgf ⋅m/lb ⋅in)
10 (1.0 / 87)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

2B-12 SHEET METAL


Important Operations - Installation
4. Control Cable
Reroute the control cable to its original position, and check to
see if the lock assembly and control lever work normally.

2. Engine Hood Lock Assembly

Adjustment
1) Install the engine hood lock assembly (4) and temporaril
y
tighten the bolts securing it.
2) Close the hood.
3) Position the hood so that the stepped portion between the hood (1) and the fender (2) is precisely 1.5 mm (0.06 in)
high.
4) Finally tighten the bolts securing the engine hood lock assembly.


5) Turn the buffers (3) counterclockwise until the stepped
portion between the hood and the fender disappears.
6) Tighten the hood lock assembly fixing bolts to the specified torque.

Torque N ⋅m(kgf ⋅m/lb ⋅in)
10 (1.0 / 87)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

2B-14 SHEET METAL


Important Operations - Installation
5. Control Cable
Reroute the control cable to its original position, and check to
see if the lock assembly and control lever work normally.

3. Engine Hood Lock Assembly

Adjustment
6) Install the engine hood lock assembly (4) and temporaril
y
tighten the bolts securing it.
7) Close the hood.
8) Position the hood so that the stepped portion between the hood (1) and the fender (2) is precisely 1.5 mm (0.06 in)
high.
9) Finally tighten the bolts securing the engine hood lock assembly.


10) Turn the buffers (3) counterclockwise until the stepped
portion between the hood and the fender disappears.
6) Tighten the hood lock assembly fixing bolts to the specified torque.

Torque N ⋅m(kgf ⋅m/lb ⋅in)
10 (1.0 / 87)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

2B-16 SHEET METAL


Important Operations - Removal
1. Radiator Grille
Refer to the Radiator Grille in this section.
3. Front wheel extension (W/front wheel extension)
Refer to the SECTION 10 “Front W heel Extension”.





4. Inner Liner

Remove the inner liner fixing screws.





5. Front Bumper Fascia

Refer to the Front Bumper in this section.



RTW 72BSH000201

7. Front Fender Panel

Remove the 8 fixing bolts.








Important Operation - Installation
7. Front Fender Panel
1) Tighten the front fender panel fixing bolts to the
specified torque.

Torque N ⋅m(kgf ⋅m/lb ⋅in)
10 (1.0 / 87)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007