Page 84 of 6020
1-50 HEATER AND AIR CONDITIONING
Important Operations - Installation
4. Bolt; Compressor to Bracket
N⋅m (kgf ⋅m/lb ⋅ft)
Torque 44 (4.5/33)
3. Refrigerant Line
N⋅m (kgf ⋅m/lb ⋅in)
Torque 11 ∼19 (1.1/95 ∼1.9/168)
2. Drive Belt
Refer to SECTION 6A “V-BELT TENSION OF ALTERNATER”.
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 92 of 6020
1-58 HEATER AND AIR CONDITIONING
Important Operations - Reassembly
RTW 510SH001001
2. Field Coil
Installation field coil. • Align the located portion (1) of the clutch coil and
compressor.
RTW 510SH001101
4. Pulley Assembly
Using pulley installer and drive handle to install the pulley assembly.
Pulley Installer: 5-8840-0118-0 (J-33940)
Drive Handle: 5-8840-0007-0 (J-8092)
RTW 510SH000701
8. Drive Plate Bolt
Using drive plate holder to prevent the drive plate from rotating.
Drive Plate Holder: 5-8840-4056-0 (J-37872) Tighten the bolt to the specified torque. N⋅m (kgf ⋅m/Ib ⋅in)
Torque 13 (1.3/113)
After tightening the bolt, check to be sure the pulley rotates
smoothly.
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 157 of 6020
FRAME AND BUMPER 2A-3
Important Operations - Removal
1. Radiator Grille
Refer to the Radiator Grille in this section.
RTW 72ASH000501
2. Front Bumper Fascia
• Remove the 7 clips and 4 bolts.
• Disconnect the fog light harness connectors.
RTW 52ASH000401
5. Bumper Seal
Remove the 6 clips.
Important Operations - Installation
RTW 52ASH000301
7. Front Bumper Impact Bar Assembly
Tighten the fixing bolts to the specified torque.
Torque N ⋅m(kgf ⋅m/lb ⋅ft)
62 (6.3 / 46)
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 158 of 6020
2A-4 FRAME AND BUMPER
RTW 72ASH000601
4. Fog Light
Tighten the fixing nuts to the specified torque.
Torque N ⋅m(kgf ⋅m/lb ⋅in)
7 (0.7 / 61)
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 160 of 6020
2A-6 FRAME AND BUMPER
Important Operations - Removal
1. Front Combi Lamp Assembly
2. Radiator Grille
Refer to the Radiator Grille in this section.
RTW 52ASH000101
3. Front Bumper Fascia
• Remove the 9 clips and 4 screws.
• Disconnect the fog light harness connectors.
RTW 52ASH000401
6. Bumper Seal
Remove 6 clips.
Important Operations - Installation
10. Front Bumper Impact Bar Assembly
Tighten the fixing bolts to the specified torque.
Torque N ⋅m(kgf ⋅m/lb ⋅ft)
62 (6.3 / 46)
7. Front Bumper Flare Assembly
Tighten the fixing nuts to the specified torque.
Torque N ⋅m(kgf ⋅m/lb ⋅in)
7 (0.7 / 61)
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 161 of 6020
FRAME AND BUMPER 2A-7
5. Fog Light
Tighten the fixing nuts to the specified torque.
Torque N ⋅m(kgf ⋅m/lb ⋅in)
7 (0.7 / 61)
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 163 of 6020
FRAME AND BUMPER 2A-9
Important Operations - Removal
1. Rear Step Bumper Assembly
• Remove the 3 bolts from each side.
• Disconnect the extension harness connector.
1
1
RTW 72ASH000701
2. Side Step Pad
• Push out the 4 fixing portions (1) of side step pad from
the back face of the rear step bumper.
RTW 72ASH000801
4. Rear Bumper Center Pad
• Remove the 2 clips (1) from both ends of the center pad.
• Push out the 5 fixing portions (2) of the center pad from
the back face of the rear step bumper.
RTW 72ASH000901
Important Operations - Installation
9. Reinforcement assembly • Tighten the fixing bolts to the specified torque.
Bolt (5)
Torque N ⋅m(kgf ⋅m/lb ⋅ft)
85 (8.7 / 63)
7. Shell Bolt (2), (3)
Torque N ⋅m(kgf ⋅m/lb ⋅ft)
42 (4.3 / 31)
6. Center bar Bolt (1)
Torque N ⋅m(kgf ⋅m/lb ⋅in)
7 (0.7 / 61)
Bolt (4)
Torque N ⋅m(kgf ⋅m/lb ⋅ft)
18 (1.8 / 13)
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 164 of 6020
2A-10 FRAME AND BUMPER
RTW 72AMH000101
1. Rear Step Bumper Assembly
1) Align the back bar to the frame (1) as follows:
• Face A (2) should be in contact with the upper face o
f
the frame.
• Face B (3) should be in contact with the rear end o
f
the frame.
2) Tighten the 3 fixing bolts on each side of the back bar.
Torque N ⋅m(kgf ⋅m/lb ⋅ft)
150 (15.3 / 111)
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
