2007 ISUZU KB P190 torque

3B-6 POWER-ASSISTED STEERING SYSTEM
Steering Column

RTW 53BLF000901
WARNING: TO AVOID DEPLOYMENT WHEN
TROUBLE-SHOOTING THE SRS SYSTEM, DO NOT
USE ELECTRICAL TEST EQUIPMENT, SUCH AS
A
BATTERY-POWERED OR A/C-POWERED
VOLTMETER, OHMMETER, ETC., OR ANY TYPE OF
ELECTRICAL EQUIPMENT OTHER THAN SPECIFIED
IN THIS MANUAL. DO NOT USE A NON-POWERED
PROBE-TYPE TESTER.
INSTRUCTIONS IN THIS MANUAL MUST BE
FOLLOWED CAREFULLY, OTHERWISE PERSONAL
INJURY MAY RESULT.
W hen servicing a vehicle equipped with a Supplemental
Restraint System, pay close attention to all W ARNINGS
and CAUTIONS.
For detailed explanations about SRS, refer to Restraints
section.
The steering column has three important features in
addition to the steering function:
1. The column is energy absorbing, designed to
compress in a front-end collision to minimize the
possibility of injury to the driver of the vehicle.
2. The ignition switch and lock are mounted conveniently on the column.
3. W ith the column mounted lock, the ignition and steering operation can be locked to prevent theft o
f
the vehicle.
The column can be disassembled and reassembled.
However, to insure the energy absorbing action, use
only the specified screws, bolts and nuts as designated,
and tighten them to the specified torque.
Handle the column with care when it is removed from
the vehicle. A sharp blow on the end of the steering
shaft or shift lever, or dropping the assembly could
shear or loosen the fasteners that maintain column
rigidity.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

POWER-ASSISTED STEERING SYSTEM 3B-9
4. Install all the lines and hoses. Fill the system with
new power steering fluid and bleed the system as
described in Bleeding the Power Steering System.
Operate the engine for about 15 minutes.
Remove the pump return line at the pump inlet and
plug the connection on the pump. W hile refilling the
reservoir, check the draining fluid for contamination.
If foreign matter is still evident, replace all lines,
disassemble and clean or replace the powe
r
steering system components. Do not re-use any
drained power steering fluid.

Steering Wheel Free Play Inspection
RTW 73BSH000901
1. W ith the tires in the straight-ahead position, check the amount of steering wheel play by turning the
wheel in both directions until the tires begin to move.
NOTE: The wheel free play should be checked with the
engine running. Free play: 0 - 30 mm (0 - 1.18 in)
2.
Also check the steering wheel for play and
looseness in the mount by moving it back and forth
and sideways. W hen test driving, check for hard
steering, steering shimmy and tendency to pull to
one side.

Front End Alignment Inspection and
Adjustment
Toe-in Adjustment
Toe-in: Refer to Section 3A FRONT ALIGNMENT
1. To adjust the toe-in angle, loosen the lock nuts (2) on the tie rod (1) and turn the tie rod. Turn both rods
the same amount, to keep the steering wheel
centered .
431R30006
2. Tighten the lock nut to the specified torque. Torque:
98 N ⋅
⋅⋅
⋅
m (10 kgf ⋅
⋅⋅
⋅
m/72 lb ⋅
⋅⋅
⋅
ft)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3B-10 POWER-ASSISTED STEERING SYSTEM
Torque Specification
N⋅m (kgf ⋅m/Ib ⋅ft)

RTW 53BLF001001

Special Tools

ILLUSTRATION
TOOL NO.
TOOL NAME
ILLUSTRATION

TOOL NO.
TOOL NAME
5-8840-0135-0
(J-29877-A) Tester;
Power steering 5-8840-2297-0
(J-39213) Adapter;
Power steering tester


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3B-12 POWER-ASSISTED STEERING SYSTEM
901RW 270
4. Disconnect the feed line and return line from
steering unit.
Remove the clips on the crossmember and frame.
W ire the power steering line to frame.
NOTE: Take care to prevent foreign matter from
entering when disconnecting the power steering line.
5. Remove the power steering unit from the crossmember.

Installation
1. Install power steering unit on crossmember.
Tighten fixing bolt and nut to specified torque.
Torque:
116 N ⋅
⋅⋅
⋅
m (11.8 kgf ⋅
⋅⋅
⋅
m/85 lb ⋅
⋅⋅
⋅
ft)
Torque:
220 N ⋅
⋅⋅
⋅
m (22.4 kgf ⋅
⋅⋅
⋅
m/162 lb ⋅
⋅⋅
⋅
ft)
2. Connect the feed line and return line. Torque:
25 N ⋅
⋅⋅
⋅
m (2.5 kgf ⋅
⋅⋅
⋅
m/18 lb ⋅
⋅⋅
⋅
ft)
3. Install tie-rod end assembly on knuckle. Torque:
98 N ⋅
⋅⋅
⋅
m (10 kgf ⋅
⋅⋅
⋅
m/72 lb ⋅
⋅⋅
⋅
ft)
4.
Align the setting marks on the universal joint
(applied at disassembly) with the setting marks on
the power steering unit. Connect the universal joint
assembly to the power steering unit.
5. Tighten the universal joint bolt to the specified torque.
Torque:
31 N ⋅
⋅⋅
⋅
m (3.2 kgf ⋅
⋅⋅
⋅
m/23 lb ⋅
⋅⋅
⋅
ft)
6. Install the stone guard.
7. Bleed the system. Refer to Bleeding the Power Steering System in this
section.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3B-14 POWER-ASSISTED STEERING SYSTEM
Disassembly
NOTE : The valve hosing is made of aluminum and care
should be exercised when clamping in a vise, etc.
to prevent distortion or damage.
For the left side, follow the same steps as right side.
1. Loosen lock nut and remove tie-rod end.
2. Remove clip and band, then remove bellows.
• Use a pair of pliers to open the clip. Slide the cliptoward the tie-rod end.





RUW 53BSH000401
• Remove band from the bellows by using
screwdriver.





RUW 53BSH000501


CAUTION :
For 4 ×
××
×
2 except High ride suspension models;
The band is not reusable. If removed, it must be
replaced with a new one.
Take care not to damage the bellows during band
removal.
For 4 ×
××
×
4 and 4 ×
××
×
2 High ride suspension models;
The band and bellows are not reusable. If removed,
they must be replaced with a new one.
3. Remove tie-rod assembly.
To remove, move the boot toward the tie-rod end, then remove tab washer.
4. Remove oil line, mounting rubber and dust cover.

Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found during inspection.
Check the following parts.
1. Tie-rod end
2. Lock nut
3. Clip
4. Bellows
5. Band
Tie-Rod End
If looseness or play is found when checked by moving
the end of ball joint at tie-rod end, replace tie-rod end.

Tie-Rod Assembly
If the resistance is insufficient or play is felt when
checked by moving the ball on the tie-rod, replace the
tie-rod assembly.

Rubber Parts
For 4 ×2 except High ride suspension models;
If wear or damage is found during inspection, replace
with new ones.
For 4 ×4 and 4 ×2 High ride suspension models;
Even if wear or damage is not found after removal,
replace with new ones.

Reassembly
1. Install mounting rubber and dust cover (If removed).
2. Install oil line. Torque: 12 N ⋅
⋅⋅
⋅
m (1.2 kgf ⋅
⋅⋅
⋅
m/104 lb ⋅
⋅⋅
⋅
in)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

POWER-ASSISTED STEERING SYSTEM 3B-15
3. Install tie-rod assembly with tab washer, then tighten
to specified torque. For 4 ×2 except High ride suspension models;
Torque: 83 N ⋅
⋅⋅
⋅
m (8.5 kgf ⋅
⋅⋅
⋅
m/61 lb ⋅
⋅⋅
⋅
ft)
For 4 ×4 and 4 ×2 High ride suspension models;
Torque: 108 N ⋅
⋅⋅
⋅
m (11.0 kgf ⋅
⋅⋅
⋅
m/80 lb ⋅
⋅⋅
⋅
ft)
After tightening, bend tab washer against width
across flat of inner ball joint.
4. Apply grease to the tie-rod groove. Install bellows on housing assembly.
CAUTION :
Make sure that there are no bulges or dents in the
bellows.
After installation, confirm the small end of the
bellows is inserted into the tie-rod groove.











RUW 53BSH000301

5. Caulk the band using clamp pliers 5-8840-2745-0.
For 4 ×2 except High ride suspension models;
Caulk gap(A): less than 2.0mm(0.08in).
For 4 ×4 and 4 ×2 High ride suspension models;
Caulk gap(A): 2.6 – 3.3mm(0.10 – 0.13in).

CAUTION :
Be sure to use a new band.





RUW 53BSH000601
6. Install clip.
7. Install tie-rod end and tighten lock nut.
Torque:
98 N ⋅
⋅⋅
⋅
m (10 kgf ⋅
⋅⋅
⋅
m/72 lb ⋅
⋅⋅
⋅
ft)


Main Data and Specifications
General Specifications
2W D 4W D
Power steering W ithout W ith
Type Rack and pinion
Rack stroke mm (in) 138 (5.43) 138 (5.43) 152 (5.98)
Steering unit
Lock to lock 4.84 3.38 3.23


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3B-16 POWER-ASSISTED STEERING SYSTEM
Torque Specifications
N⋅m (kgf ⋅m/Ib ⋅ft)





RTW 73BLF000801

Special Tools

ILLUSTRATION
TOOL NO.
TOOL NAME
ILLUSTRATION

TOOL NO.
TOOL NAME



5-8840-2005-0
(J-29107)
Tie rod end remover






5-8840-2745-0 Clamp plier


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

POWER-ASSISTED STEERING SYSTEM 3B-17
Power Steering Pump (4JH1-TC, 4JA1-T)
Power Steering Pump and Associated Parts


RTW 53BMF000401
Legend (1) Pump Assembly
(2) Suction Hose
(3) Flexible Hose
(4) Bolt
(5) Bracket


Removal
1. Remove the drive belt.
2. Remove the pulley
3. Place a drain pan below the pump.
4. Disconnect the suction hose.
5. Disconnect the flexible hose.
6. Remove the power steering fixing bolt and remove the pump assembly.

Installation
1. Install the pump assembly to the pump braket,
tighten the fixing bolt to the specified torque.
Torque: 40 N·m (4.1 kgf·m/30 lb·ft)
2. Install the flexible hose.
Tighten the nut to specified torque.
Torque: 20 N·m (2.0 kgf·m/14 lb·ft)
3. Install the pulley and tighten the bolt to the specified torque.
Torque: 28 N·m (2.9 kgf·m/21 lb·ft)
4. Install the drive belt.
5. Connect the suction hose, then fill and bleed system.
Refer to Bleeding the Power Steering System in this section.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007