2007 ISUZU KB P190 clock

3B-56 POWER-ASSISTED STEERING SYSTEM
9. Turn the SRS coil fully counterclockwise, return
about 3 turns and align the neutral mark (1). (with
SRS air bag)
CAUTION: When turning the SRS coil fully
counterclockwise, stop turning if resistance is felt.
Further forced turning may damage to the cable in
the SRS coil.
826RW 014
10. W hen installing the steering column cover, be sure to
route each wiring harness as illustrated so that the
harnesses do not catch any moving parts.
825RW 017
Legend
(1) Steering Column Cover
(2) Starter Switch Harness
(3) Combination Switch Harness
(4) Inflator Module Harness

11. Install steering wheel and align the setting marks
made when removing. Refer to the adjustment method in case a mark has
not been applied in this section.
NOTE: Confirm SRS and horn harness connector is
fixed by the steering wheel.

RTW 73BSH000701

CAUTION: Never apply force to the steering wheel in
the direction of the shaft by using a hammer o
r
other impact tools in an attempt to remove the
steering wheel. The steering shaft is designed as an
energy absorbing unit.
12. Tighten the steering wheel fixing nut to the specified torque.
Torque: 35 N ⋅
⋅⋅
⋅
m (3.6 kgf ⋅
⋅⋅
⋅
m/26 lb ⋅
⋅⋅
⋅
ft)
13. Support the module and carefully connect the module connector and horn lead, then install inflato
r
module.
NOTE: Pass the lead wire through the tabs on the
plastic cover (wire protector) of inflator to prevent lead
wire from being pinched.
14. Tighten bolts to specified torque.
Torque: 3 N ⋅
⋅⋅
⋅
m (0.3 kgf ⋅
⋅⋅
⋅
m/26 lb ⋅
⋅⋅
⋅
in)
15. Install driver knee bolster (reinforcement).
16. Install instrument panel lower cover.
17. Install the engine hood opening lever.
18. Connect the yellow 2-way SRS connector and horn lead located under the steering column.
19. Connect the battery "-" terminal cable (with SRS ai
r
bag).


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

REAR AXLE 4B-25
b. Tighten the nut to the specified torque.
Torque:
φ220mm : 2.7 N ⋅m (0.28 kgf ⋅m/24 lb ⋅in)
φ194mm : 2.3 N ⋅m (0.23 kgf ⋅m/20 lb ⋅in)



425RW 030

c. Clean the side bearing bores. Place discs and
dial indicator on to arbor, and place tool into
position in side bearing bores. Install and
tighten the bearing caps to the specified
torque.
Torque : φ220mm : 108N ⋅m (11 kgf ⋅m/80 lb ⋅ft)
φ194mm : 94N ⋅m (10 kgf ⋅m/72 lb ⋅ft)

425RW 031
Legend
φ
φφ
φ
220mm
1. Dial Indicator : 5-8840-0126-0
2. Gauge Plate : 5-8840-2166-0
3. Disc (2 pcs.) : 5-8840-2167-0
4. Arbor : 5-8840-0128-0
φ
φφ
φ
194mm
1. Dial Indicator : 5-8840-0126-0
2. Gauge Plate : 5-8840-2087-0
3. Disc (2 pcs.) : 5-8840-2088-0
4. Arbor : 5-8840-0128-0



Note :
The scale on the dial indicator (5-8840-0126-0) is
inch unit.
d. Set the dial indicator 5-8840-0126-0 to “0”.
Place it on the mounting post of the gauging
arbor with the contact button touching the
indicator pad. Force the dial indicato
r
downward until the needle has made a hal
f
turn clockwise. Tighten down the dial indicato
r
in this position.




425RS020
Legend
1. Dial Indicator
2. Gauging Arbor
3. Plunger
4. Gauge Plate


e. Position the plunger on the gauge plate. Move
the gauging arbor slowly back and forth and
locate the position at which the dial indicato
r
shows the greatest deflection. At this point,
once again set the dial indicator to “0”.
Repeat the procedure to verify the “0” setting.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRONT WHEEL DRIVE 4C1-31








Tighten the nut to the specified torque.
N⋅m (kgf ⋅m/lb ⋅in)
New bearing 2.3 (0.23/20)
Used bearing 0.98 - 1.18
(0.10 – 0.12/9 – 10)
(2) Clean the side bearing bores. Install the dial indicator with the discs and Arbor. Install and tighten the bearing caps to
the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
98 (10.0/72)

1 Dial indicator : 5-8840-0126-0
2 Disc (2 pcs.) : 5-8840-2088-0
3 Arbor : 5-8840-0128-0
4 Gage plate : 5-8840-2087-0




(3) Set the dial indicator to “0”. Place it on the mounting post of
the gaging arbor with the contact button touching the
indicator pad. Force the dial indicator downward until the
needle has made a half turn clockwise. Tighten down the
dial indicator in this position.




(4) Position the plunger on the gage plate. Move the gaging
arbor slowly back and forth and locate the position at which
the dial indicator shows the greatest deflection. At this
point, once again set the dial indicator to “0”.
Repeat the procedure to verify the “0” setting.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-54 FRONT WHEEL DRIVE



Important Operations
1. Bolt
Before removal, shift transfer lever into “2H” position and set
free wheeling hub knob into “FREE” position.



6. Hub nut
W rench : 5-8840-2 117-0




7. Hub and disc assembly
Before disassembly, remove the disc brake caliper assembly
and hang it on the frame with wires.
Refer to Section “Brake” for disc brake caliper removal
procedure.



14. Clutch Assembly
W hile pushing follower knob, turn clutch assembly clockwise
and then remove clutch assembly from knob.





19. Retaining Spring
Remove retaining spring from clutch assembly by turning it
counterclockwise.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-58 FRONT WHEEL DRIVE





Important Operations
1. Spacer
Apply grease to both faces of spacer.
4. Inner Assembly
Apply grease wheel bearing to inside face of ring.
g(oz)

Amount of grease 6 (0.21)



7. Knob
( 1 ) Apply grease W heel bearing to outer circumference of knob
and inner circumference of cover.
(2) Align detent ball to either groove of cover.





8. Snap Ring
Turn the smoother face to knob side.
9. Retaining Spring
Align the end of spring to the end of cut portion of clutch spring
groove.




10. Follower
Install follower to clutch so that follower nail will come closer to
the bent portion of retaining spring by aligning follower stopper
nail to outer teeth of clutch. Then, hook retaining spring onto
upper portion of hanger nails of follower.





11. Compression Spring
Turn the smaller diameter side to follower.
12. Clutch Assembly
Align follower nail to handle groove, and then assemble clutch
with knob by pushing and turning clutch counterclockwise to
knob.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5C-24 BRAKES
RTW 35CSH000201
3) Rear wheel cylinder fluid pressure measurement
Step on the brake pedal until the fluid pressure of the front wheel cylinder gets to 9.8Mpa (100kg/cm
2), and
check the rear wheel cylinder fluid pressure. (Read the
value of the front wheel cylinder fluid pressure 2
seconds after the measurement. W hen measuring the
LSPV fluid pressure, keep the brake pedal pressed
down without stepping it down twice or releasing it.)
Rear W heel Cylinder Fluid Pressure MPa (kg/cm
2)
2W D 6.77 ±0.83 (69.0 ±8.5)
2W D (W ith High Ride
Suspension), 4W D 6.77
±0.83 (69.0 ±8.5)

RTW 35CSH000401
2. Oil Pressure Adjustment
1) LSPV spring length adjustment
Loosen the adjust nut of the LSPV spring joint, and adjust the length of the LSPV spring.
W hen the oil pressure is insufficient, turn the adjust nut clockwise to extend the span “A”. W hen the oil pressure
is too high, turn the adjust nut counterclockwise to
reduce the span “A”.


2) After adjustment, tighten the lock nut securely.
Lock Nut Torque N⋅m (kgf ⋅m/lb ⋅ft)
11-20 (1.1-2.0/8-14)


















BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

BRAKES 5C-31
ADJUSTMENT PROCEDURE OF BRAKE PEDAL



The push rod serves as the brake pedal stopper when the
pedal is fully released.
Brake pedal height adjustment should be performed as follows.

RTW 35CSH000601


Brake Pedal - Height
Measure the brake pedal height after making sure the pedal is
fully returned by the pedal return spring.
Note:
Pedal height (L2) must be measured after starting the
engine and increasing the revolution several times by
stepping on the accelerator pedal. mm (in)
Pedal free play (L1) 6 - 10 (0.24 - 0.39)
M/T 174 - 186 (6.85 - 7.32) Height (L2)
A/T 176 - 188 (6.93 - 7.40)
Note:
Pedal free play must be measured after turning off the
engine and stepping on the brake pedal firmly five times
or more.
If the measured value deviates from the above range, adjust
the brake pedal as follows:
a) Disconnect the stop lamp switch.
b) Loosen the lock nut on the push rod.
c)
Adjust the brake pedal to the specified height by rotating the
push rod in the appropriate direction.



Lock Nut Torque
N⋅m (kgf ⋅m/lb ⋅
⋅⋅
⋅
ft)
15 - 25 (1.5 – 2.5 / 11 - 18)

d) Install the stop lamp switch.

Note:
Pedal height (L
2) must be 57 mm (2.24 in.) or more when
applying about 50 kg (110.25 lbs.) of stepping force.

331R300005

How to connect the CLEVICE of the BOOSTER ROD with the
PEDAL ARM and how to adjust the PEDAL SW .
After connecting the CLEVIS of the BOOSTER ROD to the
PEDAL ARM, adjust the PEDAL SW mounted (PDA) to the
PEDAL BRACKET using the procedure explained below.
1. Set the hole of the CLEVIS of the BOOSTER & M/CYL
ROD with the hole in the PEDAL ARM.
2. Enter the PIN; PUSH ROD to the PEDAL to the holes from the left side of the PEDAL.
3. Enter and fix the PIN; SNAP PIN FIX to the DITCH o
f
the PIN; PUSH ROD to PEDAL from right side of the
PEDAL.
4. Release the LOCK by turning the SW ITCH counter- clock-wise.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5C-32 BRAKES

5. Pull the PEDAL ARM a little towards you so that the
PEDAL ARM is not pushed in.
6. Holding the PEDAL ARM still with one hand, push in the whole SW ITCH with the other hand until the PLUNGER
of the SW ITCH is pushed in and the SW ITCH itself hits
the RUBBER of the PEDAL ARM.
In this condition, turn the SW ITCH clock-wise until a “click” sound is heard and lock it.
By doing this the SW ITCH is adjusted at 0.7 ±0.5 mm
(0.028 ± 0.020 in) clearance.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007