2007 ISUZU KB P190 clock

ELECTRICAL-BODY AND CHASSIS 8A-167


HEADLIGHT (HALOGEN STD TYPE)
(A type)
Removal
1. Remove the head light socket.
2. Remove the headlight dust cover.


3. Slide out the lock spring.


4. Remove the bulb.



1
RTW 78ASH000801

HEADLIGHT (HALOGEN PROJECTOR
TYPE)
Removal
1. Remove the head light socket.
2. Remove the headlight dust cover
1.



1

RTW 78ASH000901
3. Turn the bulb socket counterclockwise to remove it.
4. Remove the headlight bulb
1.

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-168 ELECTRICAL-BODY AND CHASSIS
HALOGEN HEADLIGHT BULB (B type)
Removal
1. Open the bonnet.
2. Disconnect the headlight bulb connectors.

RTW 580SH000101
3. Turn the bulb counterclockwise to remove it.


Installation
To install the headlight, follow the removal procedure in
reverse order.
Pay close attention to the important points mentioned in the
following paragraphs.

Connector
Be absolutely sure that the headlight connector is securely
connected.
This will prevent a contact and an open circuit.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-170 ELECTRICAL-BODY AND CHASSIS

FRONT TURN SIGNAL LIGHT BULB
(A type)
Removal

HALOGEN STD TYPE RTW 78ASH000201

1. Turn the socket counterclockwise to disconnect it from the
front turn signal light housing.
2. Turn the bulb
1 counterclockwise to remove it.



1

HALOGEN PROJECTOR TYPE RTW 78ASH001001



FRONT COMBINATION LIGHT
ASSEMBLY (B type)
Removal
1. Open the bonnet.

RTW 580SH000901
2. Remove the bolt of front combination light assembly
3. Disconnect the front combination light harness connector.
4. Remove the front combination light assembly.


Installation
To install the front combination light assembly follow the
removal procedure in the reverse order.



Connector
Be absolutely sure that the front combination light harness
connector is correctly installed.
This will prevent a poor contact and an open circuit.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-171
FRONT TURN SIGNAL LIGHT BULB
Removal

RTW 580SH000201

1. Remove the front combination light assembly.
• Refer to “FRONT COMBINATION LIGHT ASSEMBLY”
removal procedure in this section.
2. Turn the bulb counterclockwise to remove it. (Gray socket side)


Installation
Follow the removal procedure in the reverse order to install the
front turn signal light.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the clearance light connector is
securely connected.
This will prevent a poor contact and an open circuit.


CLEARANCE LIGHT BULB (A type)
Removal

HALOGEN STD TYPE RTW 78ASH000301

1. Turn the socket counterclockwise to disconnect it from the
clearance light housing.
2. Turn the bulb
1 counterclockwise to remove it.



1 HALOGEN PROJECTOR TYPE RTW 78ASH001101


BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-172 ELECTRICAL-BODY AND CHASSIS
CLEARANCE LIGHT BULB (B type)
Removal


RTW 580SH000301

1. Remove the front combination light assembly.
• Refer to “FRONT COMBINATION LIGHT ASSEMBLY”
removal procedure in this section.
2. Turn the bulb counterclockwise to remove it. (Black socket side)


Installation
Follow the removal procedure in the reverse order to install the
clearance light.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the clearance light connector is
securely connected.
This will prevent a poor contact and an open circuit.



LICENSE PLATE LIGHT
Removal
1. Remove the lens cover 1 and the connector 2.
2. Pull the bulb
3 to remove it.



Installation
Follow the removal procedure in the reverse order to install the
license plate light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that the license plate light bulb is correctly
installed.
This will prevent a poor contact and open circuit.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-187

RTW 780SH000601
FOG LIGHT (A type)
Removal
1. Disconnect the fog light connector 1 .
2. Remove two attaching nuts
2.
3. Pull the fog light assembly toward the vehicle front to remove it from the holding bracket
3 .
4. Remove the bulb with socket. • Turn the socket
4 counterclockwise to remove it.
5. Remove the bulb. • Release the lock spring.
• Pull out the bulb.


FOG LIGHT (B type)
Removal
1. Remove the radiator grille.
2. Remove the front bumper
3. Disconnect the fog light connector.
4. Remove the fog light.


5. Remove the bulb from the socket.
• Remove the cover by turning it counterclockwise out
side the lock spring.
• Remove the bulb.



Hold the bulb by the flange when replacing it.
Do not touch the bulb with your hands.

Installation
To install the fog light, follow the removal procedure in reverse
order.
Pay close attention to the important points mentioned in the
following paragraphs.





Bulb
Be absolutely sure that the fog light bulb is correctly installed.
This will prevent a poor contact and open circuit.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-193




RTW 48ASH000701

REAR FOG LIGHT
Removal
1. Remove the screws 1.
2. Remove the lens cover
2.
3. Rear fog push turn the bulb
3 counterclockwise to
disconnect it from the light housing.



Installation
Follow the removal procedure in the reverse order to install the
rear fog light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that the license plate light bulb is correctly
installed.
This will prevent a poor contact and open circuit.




RTW 78ASH000401
FRONT FOG & RR FOG SWITCH



RTW 48ASH000401
Inspection
Check to see if there is any continuity between the terminals of
the leveling switch.
Replace the switch when the result of inspection is found
abnormal.

Removal
Preparation:
Disconnect the battery ground cable.
1. Ventilation grille
2. Harness connector
3. Front fog light & Rear fog light switch To remove the switch, push the lock from the back side of
the cluster assembly.
4. Remove the bulb.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-235
REMOVAL AND INSTALLATION



A Type
RTW 780SH002101

REAR COMBINATION LIGHT
Stoplight
Removal
1. Open the tail gate.
2. Remove the screws of rear combination light.
3. Remove the rear combination light assembly.




B Type
RTW 580SH000401



A Type
RTW 780SH001201
4. Turn the bulb (1) counterclockwise to remove it.




B Type
RTW 580SH000501



Installation
Follow the removal procedure in the reverse order to install the
rear combination light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that each bulb is correctly installed.
This will prevent a poor contact and an open circuit.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007