2007 INFINITI QX56 battery

AUDIO
AV-45
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
Check that the following fuse is not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of blown fuse before installing new fuse. Refer to PG-
3.
2.POWER SUPPLY CIRCUIT CHECK
1. Disconnect subwoofer connector.
2. Check voltage between the subwoofer and ground.
OK or NG
OK >> GO TO 3.
NG >> • Check connector housings for disconnected or loose
terminals.
• Repair harness or connector.
3.GROUND CIRCUIT CHECK
Check continuity between subwoofer harness connector B72 termi-
nal 5 and ground.
OK or NG
OK >> GO TO 4.
NG >> • Check connector housings for disconnected or loose
terminals.
• Repair harness or connector.
4.CHECK SUBWOOFER AMP. ON SIGNAL
1. Operate system and check voltage between subwoofer harness
connector B72 terminal 4 and ground.
OK or NG
OK >> GO TO 5.
NG >> • Check connector housings for disconnected or loose
terminals.
• Repair harness or connector.
5.HARNESS CHECK
1. Disconnect BOSE speaker amp. connector M112 and subwoofer connector B72.
Unit Terminal Signal name Fuse No.
Subwoofer 6 Battery power 17
UnitTerminal No.
OFF ACC ON (+)
(-)
Connector Terminal
Subwoof-
erB72 6 GroundBattery
voltageBattery
voltageBattery
voltage
WKIA1601E
Continuity should exist.
WKIA1602E
Voltage : More than approx. 6.5V
WKIA2078E

AUDIO
AV-47
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
2. Remove audio unit screws, using power tool.
3. Pull out audio unit and disconnect audio unit connectors.
Installation
Installation is in the reverse order of removal.
AV SWITCH
Removal
1. Disconnect battery negative terminal.
2. Remove center console. Refer to IP-10
.
3. Disconnect center speaker.
4. Remove AV switch screws.
5. Carefully remove the AV switch.
Installation
Installation is in the reverse order of removal.
BOSE SPEAKER AMP.
Removal
1. Remove the accelerator pedal. Refer to ACC-3.
2. Remove BCM. Refer to BCS-24, "
BCM".
3. Disconnect Bose speaker amp. and satellite radio tuner (if equipped) connectors.
4. Remove Bose speaker amp./satellite radio tuner bracket screws
and slide Bose speaker amp./satellite radio tuner bracket down.
WKIA1490E
WKIA1798E
WKIA1605E

AV-60
< SERVICE INFORMATION >
TELEPHONE
Terminal and Reference Value for Bluetooth Control Unit
INFOID:0000000003533695
Bluetooth Control Unit Self-Diagnosis FunctionINFOID:0000000003533696
The Bluetooth control unit has two diagnostic checks. The first diagnostic check is performed automatically
every ignition cycle during control unit initialization. The second diagnostic check is performed by the techni-
cian using the steering wheel audio control switches prior to trouble diagnosis.
Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
(Approx.)Example of symptom
+–Ignition
switchOperation
1 (Y) GroundBattery pow-
erInput – – Battery voltageSystem does not
work properly.
2 (V) Ground ACC power InputACC/
ON– Battery voltageSystem does not
work properly.
3 (G/R) Ground IGN power InputON/
START– Battery voltageSystem does not
work properly.
4 (B) – Ground – – – – –
6–Shield –– – – –
7 (B) 8 (R/L) Mic-in signal Input ON – – –
9 (R/W) 10 (R) Audio out Output – – – –
11 ( B ) – M u t e – – – – –
12 (R/G) GroundRemote
control AInput ONPress MODE
switch Approx. 0V
Steering wheel audio
controls do not func-
tion. Press SEEK UP
switchApprox. 0.75V
Press VOL UP
switchApprox. 2V
Except for above Approx. 5V
13 (G/W) GroundRemote
control BInput ONPress POWER
switch Approx. 0V
Steering wheel audio
controls do not func-
tion. Press SEEK
DOWN switchApprox. 0.75V
Press VOL
DOWN switchApprox. 2V
Except for above Approx. 5V
14 (Y/R) -Remote
control
ground-- - -Steering wheel audio
controls do not func-
tion.
15 (GR) - LED - - - - -
17 (V) - - - - - - -
18 (G/O) - - - - - - -
19 (R/B) - - - - - - -
21 (B) – Ground – – – – –
28 (W/R) –Speed sig-
nal–– – – –
29 (R/W) –Microphone
power–– – – –
33 –Bluetooth
antenna sig-
nalInput – – – –

AV-62
< SERVICE INFORMATION >
TELEPHONE
2. Check voltage between connector terminals and ground as fol-
lows.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open between Bluetooth control unit and fuse.
3.CHECK GROUND CIRCUITS
1. Turn ignition switch OFF.
2. Check continuity between the following Bluetooth control unit
terminals and ground.
OK or NG
OK >> Inspection End.
NG >> Repair or replace harness.
Removal and InstallationINFOID:0000000003533698
BLUETOOTH CONTROL UNIT
Removal
1. Disconnect battery negative terminal.
2. Remove front passenger seat. Refer to SE-83
.
3. Remove Bluetooth control unit kick shield screws (A) and
remove bluetooth control unit kick shield (1).
4. Disconnect Bluetooth control unit harness connectors.
5. Remove Bluetooth control unit screws (B).
6. Remove Bluetooth control unit (2) from bluetooth control unit
bracket.
Installation
Installation is in the reverse order of removal.
NOTE:
When replacing bluetooth control unit, Perform pairing procedure. Refer to Owner's Manual Pairing Proce-
dure.
BLUETOOTH ON INDICATOR
Removal
Terminals Ignition switch position
(+)
(–) OFF ACC ON
Connector Terminal
B1411
GroundBattery
voltageBattery
voltageBattery
voltage
20VBattery
voltageBattery
voltage
30V0VBattery
voltage
WKIA4389E
Te r m i n a l s
Continuity
Connector Terminal —
B1414
Ground Yes
21
WKIA4556E
LKIA0681E

AV-70
< SERVICE INFORMATION >
DVD ENTERTAINMENT SYSTEM
Trouble Diagnosis
INFOID:0000000003533703
Power Supply Circuit InspectionINFOID:0000000003533704
1.CHECK FUSES
Check that the following fuses are not blown.
Symptom Possible causes Repair order
DVD player inoperative1. Power supply
2. Ground circuit
3. Audio enable circuit
4. DVD enable signal
5. Audio enable signal
6. DVD player
7. Audio unit1. Refer to AV- 7 0 , "
Power Supply Circuit Inspection".
2. Refer to AV- 7 0 , "
Power Supply Circuit Inspection".
3. Check audio enable circuits for open or short be-
tween audio unit terminals 39, 40 and DVD player
terminals 11, 9.
4. Push power switch of DVD player and verify approx.
5V is present at terminal 39 of audio unit.
5. Push power switch of DVD player and verify approx.
5V is present at terminal 9 of DVD player.
6. Remove DVD player for repair.
7. Remove audio unit for repair.
No sound when playing
DVD1. Audio signal circuits
2. DVD player
3. Audio unit1. Check audio signal circuits for open or short be-
tween DVD player terminals 1, 2, 3 and 4 and audio
unit terminals 34, 35, 36 and 37.
2. Remove DVD player for repair.
3. Remove audio unit for repair.
Video monitor is inopera-
tive/does not operate prop-
erly1. Power supply
2. Video monitor ground circuit
3. Video circuits
4. Data signal
5. Video monitor
6. DVD player1. Operate DVD player and verify battery positive volt-
age is present at terminals 11 and 12 of video moni-
tor. Verify approximately 5 volts is present at terminal
10 of video monitor.
2. Check video monitor ground circuits between DVD
player terminals 19 and 27 and video monitor termi-
nals 1 and 2.
3. Check video circuits between DVD player terminals
23 and 24 and video monitor terminals 7 and 8.
4. Check data signal circuit for open or short between
DVD player terminal 29 and video monitor terminal
5.
5. Remove video monitor for repair.
6. Remove DVD player for repair.
DVD remote control is inop-
erative/does not operate
properly1. Data signal
2. DVD player remote control batteries
3. DVD player remote control
4. Video monitor1. Check data signal circuit for open or short between
DVD player terminal 28 and video monitor terminal
6.
2. Replace DVD player remote control batteries.
3. Replace DVD player remote control.
4. Remove video monitor for repair.
Headphones inoperative 1. Headphone batteries
2. Headphones
3. Rear audio remote control unit1. Replace headphone batteries.
2. Replace headphones.
3. Replace rear audio remote control unit.
Snowy video/poor audio 1. Harness or connectors
2. DVD player1. Check harness and connectors for open or short.
2. Check DVD player.
Snowy video (audio OK) 1. Harness or connectors
2. DVD player1. Check harness and connectors for open or short.
2. Check DVD player.
No video (audio OK) 1. Harness or connectors
2. DVD player
3. Video monitor1. Check harness and connectors for open or short.
2. Check DVD player.
3. Check video monitor.
Dim video (audio OK) 1. Harness or connectors
2. DVD player
3. Video monitor1. Check harness and connectors for open or short.
2. Check DVD player.
3. Check video monitor.

DVD ENTERTAINMENT SYSTEM
AV-71
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of blown fuse before installing new fuse. Refer to PG-
3.
2.POWER SUPPLY CIRCUIT CHECK
1. Disconnect DVD player connector M205.
2. Check voltage between the DVD player and ground.
OK or NG
OK >> GO TO 3.
NG >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
3.GROUND CIRCUIT CHECK
Check continuity between DVD player harness connector M206 ter-
minal 22 and ground.
OK or NG
OK >> Inspection End.
NG >> • Check connector housings for disconnected or loose
terminals.
• Repair harness or connector.
Removal and InstallationINFOID:0000000003533705
DVD PLAYER
Removal
1. Disconnect battery negative terminal.
2. Remove center console compartment. Refer to IP-10
.
Unit Terminals Signal name Fuse No.
DVD player16 Battery power 31
15 Ignition switch ACC or ON 4
UnitTe r m i n a l N o .
OFF ACC ON (+)
(-)
ConnectorTe r m i n a l
(wire color)
DVD player M20516 (Y) GroundBattery
voltageBattery
voltageBattery
voltage
15 (V) Ground 0 VBattery
voltageBattery
voltage
WKIA1197E
Continuity should exist.
WKIA1198E

NAVIGATION SYSTEM
AV-89
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
Terminal and Reference Value for NAVI Control UnitINFOID:0000000003533713
Te r m i n a l N o .
(Wire color)
ItemSignal
input/
outputCondition
Vo l ta g e
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
1 (B) Ground Ground – ON – 0V –
2 (Y) Ground Battery power Input OFF – Battery voltageSystem does not
work properly.
5 (O) Ground ACC signal Input ACC – Battery voltageSystem does not
work properly.
12 (B) 14 (W)Voice guide
signalOutput ONPress the “GUIDE/
VOICE” button.Only route guide
and operation
guide are not
heard.
13 – Shield ground – – – –Audio noise in-
terference.
44 (R) 47RGB signal
(R: red)Output ONSelect “Display Di-
agnosis (NAVI)” of
CONFIRMATION/
ADJUSTMENT
function.NAVI screen
looks bluish.
45 (R/W) 47RGB signal
(G: green)Output ONSelect “Display Di-
agnosis (NAVI)” of
CONFIRMATION/
ADJUSTMENT
function.NAVI screen
looks reddish.
46 (B) 47RGB signal
(B: blue)Output ONSelect “Display Di-
agnosis (NAVI)” of
CONFIRMATION/
ADJUSTMENT
function.NAVI screen
looks yellowish.
47 – Shield ground – – – –Video display in-
terference.
48 (BR) 49RGB syn-
chronizing
signalOutput ONPress the “MAP”
button.NAVI screen is
rolling.
SKIA0171J
SKIA4977E
SKIA4978E
SKIA4979E
SKIA0164E

AV-90
< SERVICE INFORMATION >
NAVIGATION SYSTEM
49 – Shield ground – – – –Video display in-
terference.
61 (R/L) GroundIllumination
signalInput ONLighting switch in 1st
positionBattery voltageDisplay unit illu-
mination does
not change
when lighting
switch is turned
to 1st position.- Lighting switch is
OFF3V or less
63 (G/R) Ground Ignition signal Input ON – Battery voltageNavigation cur-
rent location
mark does not
indicate the cor-
rect position.
65 (G/W) GroundReverse
signalInput ONA/T selector lever in
R positionBattery voltageThe navigation
current-location
mark moves
strangely when
the vehicle is
moving back-
wards. A/T selector lever
not in R position0V
66 (W/R) GroundVeh icl e
speed signal
(8-pulse)Input ONWhen vehicle speed
is approx. 40 km/h
(25 MPH)Navigation cur-
rent location
mark does not
indicate the cor-
rect position.
68 – Shield ground – – – – –
69 (L) GroundCommunica-
tion signal (+)Input/
outputON –System does not
work properly.
70 (P) GroundCommunica-
tion signal (–)Input/
outputON –System does not
work properly.
73 74 GPS signal Input ONConnector is not
connected.5VNavigation sys-
tem GPS correc-
tion is not
possible. Te r m i n a l N o .
(Wire color)
ItemSignal
input/
outputCondition
Voltag e
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
PKIA1935E
SKIA0175E
SKIA0176E