2007 INFINITI QX56 sensor

LASER BEAM AIMING ADJUSTMENT
ACS-13
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P
2. Adjust the height of the target stand so that the point of the trian-
gle aims above the center of the ICC sensor.
ADJUSTING THE POSITION OF THE TARGET BOARD STRING
1. Attach a scale or straightedge (at least 350 mm [14 in] or
longer).
2. Suspend a string with a weight on the end 218 mm
(8.6 in) to the left side of the target board center.
POSITIONING THE TARGET
1. Suspend a string with weights on each end over the centerline of the vehicle. The string should lay over
the center of the front and back bumpers. Mark these centerpoints on the ground at each weight.
2. Connect the two center points using a string. Extend the string
an additional 5 m (16 ft) beyond the front centerpoint and mark
the floor. Position the target board weight on this mark.
3. Relocate the suspended string from the left side of the target board to the center of the target board. Mark
this point on the ground.
WKIA2039E
SKIA1211E
WKIA2040E
WKIA1851E

ACS-14
< SERVICE INFORMATION >[ICC]
LASER BEAM AIMING ADJUSTMENT
4. Pivot the target board on its center mark 20° to either side.
NOTE:
Approx. 50 mm (1.97 in) shift will produce a 20° movement.
5. Remove any items in the shaded space shown in the figure.
NOTE:
In case the background space shown in the illustration is not available, or if the background is light col-
ored, place a 400 mm (15.75 in) long frosted black board or black cloth to both sides of the target board.
Sensor AdjustmentINFOID:0000000003533785
CAUTION:
• Complete all necessary steps for laser beam adjustment until the CONSULT-II indicates "COM-
PLETED". If the procedure does not complete, the ICC system is inoperable.
• If CONSULT-II is used without connection to the CONSULT-II CONVERTER, malfunctions might be
detected during self-diagnosis.
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
PKIA2589E
WKIA1858E
BBIA0369E

LASER BEAM AIMING ADJUSTMENT
ACS-15
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P
3. Start the engine, wait for at least 10 sec., and touch “START
(NISSAN BASED VHCL)”.
4. Touch “ICC”.
If “ICC” is not indicated, go to GI-38, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
5. Touch “WORK SUPPORT”.
6. Touch “LASER BEAM ADJUST”.
7. Touch “START”.
CAUTION:
If the adjustment screen does not appear on CONSULT-II 10
sec. after touching “LASER BEAM ADJUST” screen, the fol-
lowing causes may be considered:
• Target is not set accurately.
• There is not enough space beside the target.
• Deformation of vehicle or inappropriate installation of
sensor. Sensor may be installed out of the adjustable
range.
• The area is not suitable for the adjustment work.
• ICC sensor is not clean.
BCIA0029E
BCIA0030E
BCIA0031E
SKIA6191E
WKIA2675E

ACS-16
< SERVICE INFORMATION >[ICC]
LASER BEAM AIMING ADJUSTMENT
8. After the CONSULT-II displays “ADJUST THE VERTICAL OF
LASER BEAM AIMING” turn the vertical adjusting screw until
“U/D CORRECT” value is set in the range of ±4.
CAUTION:
Turn the screw slowly. The value on the CONSULT-II is
slower than the actual movement of the ICC sensor. Wait 2
seconds between each adjustment. Also, during adjust-
ment work, do not block the ICC sensor lens with your hand
or body. In that case, there are times when aiming cannot
be conducted correctly.
NOTE:
Turning the screw clockwise raises the ICC sensor and counter-
clockwise lowers the ICC sensor.
9. When “U/D CORRECT” value indicates ±4, confirm that the value remains within ±4 for at least 2 seconds
while nothing is touching the ICC sensor.
When “COMPLETED THE VERTICAL AIMING OF LASER
BEAM” appears on screen, touch “END”.
CAUTION:
Be sure that the margin of “U/D CORRECT” is within ±4
when the ICC sensor unit is untouched.
10. Confirm that “ADJUSTING AUTOMATIC HORIZONTAL LASER
BEAM AIMING” is on screen and wait while the horizontal
adjustment is made automatically. (maximum: 10 seconds).
SKIA1221E
WKIA1869E
WKIA2676E
SKIA1224E

ACS-24
< SERVICE INFORMATION >[ICC]
TERMINALS AND REFERENCE VALUE
TERMINALS AND REFERENCE VALUE
Terminal and Reference Value for ICC UnitINFOID:0000000003533789
Terminal and Reference Value for ICC SensorINFOID:0000000003533790
Te r m i n a lWire col-
orItemCondition
Voltage (V)
(Approx.) Ignition
switchOperation
1W/L
Battery power supply OFF — Battery voltage
2W/L
5 P CAN-L — — —
7 B/R N-P RANGE ON A/T selector lever in "P" or "N" Battery voltage
10 V/R Brake booster signal ON —
14 L CAN-H — — —
19 B
Ground
ON——
20 B
29 BR/WICC brake switch
(normally closed)Selector le-
ver: Not in
“N” or “P”
positionDepress the brake
pedal0
Release the brake
pedalBattery voltage
30 L DDL-TX — — —
33 R/B Ignition switch power supply ON —
Battery voltage
38 R/GSt op la mp sw i tc h
(normally open) OFFDepress the brake pedal
Release the brake pedal 0
39 V/W DDL-RX — — —
40 G Parking brake signal
ONParking brake is ON 0
Parking brake is OFF Battery voltage
42 R/B Ignition switch power supply — Battery voltage
46 B Ground — —
47 BR Stop lamp drive output signalBrake operating with ICC system Battery voltage
Brake not operating with ICC sys-
tem0
SKIA1243E
Te r m i n a lWire
colorItemCondition
Voltage (V)
Ignition
switchOperation
1 R/B Ignition switch power supply
ON— Battery voltage
2LCAN-H — —
3PCAN-L — —
4 B Ground — —

ACS-26
< SERVICE INFORMATION >[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
CONSULT-II START PROCEDURE
Refer to GI-36, "CONSULT-II Start Procedure".
WORK SUPPORT
Work Item
Cause of Auto-Cancel
1. Touch “WORK SUPPORT” on "SELECT DIAG MODE" screen.
2. Touch “CAUSE OF AUTO-CANCEL” on "SELECT WORK ITEM"
screen.
3. Cause of automatic cancellation screen will be shown.
4. The last five causes of automatic cancellation of ICC system will
be displayed.
Possible Causes of "Auto-Cancel"
Laser Beam Adjust
For details, refer to ACS-12 .
SELF-DIAGNOSTIC RESULTS
For details, refer to ACS-34, "Diagnostic Trouble Code (DTC) Chart" .
DATA MONITOR
CAN DIAG SUPPORT MNTR The results of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Operation of electrical loads can be checked by sending driving signal to them.
ECU PART NUMBER ICC unit part number can be read.ICC diagnostic mode Description
Operation Function
CAUSE OF AUTO-CANCEL Indicates causes of automatic cancellation of the ICC system.
LASER BEAM ADJUST Outputs laser beam, calculates dislocation of the beam, and indicates adjustment direction.
SKIA6191E
Cause of cancellation Description
OPERATING WIPER Windshield wipers were operated at HI or LO speed operation.
OPERATING ABS ABS function was operated.
OPERATING TCS TCS function was operated.
OPERATING VDC VDC function was operated.
ECM CIRCUIT ECM did not permit ICC operation.
OPE SW VOLT CIRC Voltage outside the standard was detected.
LASER SUN BEAM Intense light such as sunlight entered ICC sensor light sensing part.
LASER TEMP Temperature around ICC sensor became low.
WHL SPD ELEC NOISE Wheel speed sensor signal caught electromagnetic noise.
OP SW DOUBLE TOUCH ICC steering switches were pressed at the same time.
VDC/TCS OFF SW VDC OFF switch was pressed.
WHEEL SPD UNMATCH Wheel speed became different from AT vehicle speed.
TIRE SLIP Wheel slipped.
PKB SW ON Parking brake is applied.
IGN LOW VOLT Power supply voltage became low.
NO RECORD—

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-27
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P Operation Procedure
1. Touch “DATA MONITOR” on "SELECT DIAG MODE" screen.
2. Touch “ECU INPUT SIGNALS”, “MAIN SIGNALS“, or “SELEC-
TION FROM MENU” on "SELECT MONITOR ITEM" screen.
Monitored Item
×: Applicable
BCIA0031E
WDIA0084E
Monitored Item [unit] MAIN SIGNALSECU IN-
PUT SIG-
NALSSELECTION
FROM MENUDescription
VHCL SPEED SE
[km/h] or [mph]×××Indicates vehicle speed calculated from
wheel speed sensor signal.
SET VHCL SPD
[km/h] or [mph]××Indicates set vehicle speed stored in ICC
unit.
THRTL OPENING
[%]×××Indicates throttle angle calculated from sig-
nal voltage of throttle position sensor.
ENGINE RPM
[rpm]××Indicates engine speed read by ICC unit via
CAN communication (ECM transmits engine
speed via CAN communication).
DISTANCE ADJ
[SHOR/MID/LONG]×××Indicates set distance stored in ICC unit.
WIPER SW
[OFF/LOW/HIGH]××Indicates wiper [OFF/LOW/HIGH] status.
MAIN SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
control switch signal.
SET/COAST SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
control switch signal.
CANCEL SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
control switch signal.
RESUME/ACC SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
control switch signal.
CRUISE OPE
[ON/OFF]××Indicates whether vehicle speed is being
controlled or not (ON means “controlling”).
BRAKE SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
ICC brake switch signal.

ACS-28
< SERVICE INFORMATION >[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACTIVE TEST
CAUTION:
Do not perform the active test while driving. Active test cannot be started while ICC system warning
indicator is illuminated.
Active Test
STOP LAMP SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
stop lamp switch signal.
RELEASE SW NO
[ON/OFF]
××Indicates [ON/OFF] status as judged from
release switch signal.
ON when brake is depressed.
OFF when brake is not depressed.
RELEASE SW NC
[ON/OFF]
××Indicates [ON/OFF] status as judged from
release switch signal.
OFF when brake is depressed.
ON when brake is not depressed.
IDLE SW
[ON/OFF]
××Indicates [ON/OFF] status of idle switch
read by ICC unit via CAN communication
(ECM transmits ON/OFF status via CAN
communication).
GEAR
[1, 2, 3, 4, 5]××Indicates A/T gear position read by ICC unit
via CAN communication (TCM transmits
gear position via CAN communication).
BUZZER O/P
[ON/OFF] ×Indicates [ON/OFF] status of ICC warning
output.
ICC WARNING×NOTE:
This item is displayed but cannot be moni-
tored.
VHCL SPD AT
[km/h] or [mph]
×Indicates vehicle speed calculated from A/T
vehicle speed sensor by ICC unit via CAN
communication (TCM transmits A/T vehicle
speed sensor signal via CAN communica-
tion).
PRESS SENS
[bar]×××Indicates brake fluid pressure value calculat-
ed from signal voltage of pressure sensor.
PRESS SENS 2
[bar]××NOTE:
This item is displayed but cannot be moni-
tored.
D RANGE SW
[ON/OFF]
××Indicates [ON/OFF] status of “D” position
read by ICC unit via CAN communication
(TCM transmits ON/OFF condition of “D” po-
sition via CAN communication).
A/T OD OFF
[ON/OFF]×Indicates [ON/OFF] status of OD cancel out-
put under control.
NP RANGE SW
[ON/OFF]××Indicates PNP switch signal read by ICC unit
via CAN communication. (TCM transmits
PNP switch signal via CAN communication)
DISTANCE×NOTE:
This item is displayed but cannot be moni-
tored.
RELATIVE SPD×NOTE:
This item is displayed but cannot be moni-
tored.
STP LMP DRIVE
[ON/OFF]××Indicates [ON/OFF] status of brake hold re-
lay drive output. Monitored Item [unit] MAIN SIGNALSECU IN-
PUT SIG-
NALSSELECTION
FROM MENUDescription