2007 INFINITI M35 MOTOR

GW-68
REAR DOOR GLASS AND REGULATOR
Revision: 2007 April2007 M35/M45
Disassembly and AssemblyNIS0022C
REGULATOR ASSEMBLY
Disassembly
Remove power window motor from regulator assembly.
Assembly
Assemble in the reverse order of disassembly.
Inspection after InstallationNIS0022D
SYSTEM INITIALIZATION
If any of the following work has been done, initialize the system.

Electric power sauce to power window switch or motor is interrupted by broken fuse or disconnecting bat-
tery cable, etc.

Removal and installation of the regulator assembly.

Removal and installation of the motor from the regulator assembly.

Removal and installation of the harness connector of the power window switch.

Operate the regulator assembly as a unit.

Removal and installation of the door glass.

Removal and installation of the door glass run.
Initialization
After installing each component to the vehicle, follow the steps below.
1. Disconnect the minus terminal of battery or disconnect power window switch's harness connector tempo-
rarily, then reconnect after at least 1 minute.
2. Turn ignition switch ON.
3. Open the window to its full width by operating the power window switch. (Exclude this pocedure if the win-
dow is already fully opened)
4. Fully draw the power window switch in up direction (auto close position) and hold, keep holding the switch
even when window is completely closed and then release afeter 3 second has passed.
5. Inspection of the anti-pinch system function.
NOTE:
Initialization may be cancelled with continuous opening and closing operation.In this case, initialize the
system.
INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM
1. Fully open the door glass.
2. Place a wooden piece (wooden hammer handle etc.) at near fully closed position.
3. Carry out fully closing operation with auto up switch.

Check that the glass reverses without pinching the wooden piece, is lowered approx.150mm (5.91in) or
for 2 seconds and then stops.

The glass should not be raised with power window main switch operated while it is reversing or lowering.
CAUTION:

Do not inspect with pinching a part of worker's body, a hand etc. Work carefully not to be pinched.

Check that auto up function is normal before inspection following the system initialization.
FITTING INSPECTION

Make sure the glass is securely fit into the glass run groove.

Lower the glass slightly [approx. 10 to 20 mm (0.39 to 0.79 in)], and make sure the clearance to the sash
is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator mounting bolts,
guide rail mounting bolts, and glass and carrier plate mounting bolts to correct the glass position.

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-103
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
Terminals and Reference Values for Automatic Drive Positioner Control UnitNIS00236
Te r -
minalWire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
2VChangeover switch
RH signalInputWhen changeover
switch positionRH 0
Other than above 5
3GMirror switch
UP signalInputWhen mirror switch
positionUP 0
Other than above 5
4WMirror switch
LEFT signalInputWhen mirror switch
positionLEFT 0
Other than above 5
5L/RDoor mirror RH sensor
vertical signalInputWhen door mirror
RH mirror face posi-
tionClose to perk 4.2
Close to valley 0.5
6LGDoor mirror LH sensor
vertical signalInputWhen door mirror LH
mirror face positionClose to perk 4.2
Close to valley 0.5
10 O UART LINE (TX)Input/
OutputTilt switch operated
14 LDoor mirror RH mirror
motor
UP signalOutputWhen door mirror
RH mirror motor
operationUP Battery voltage
Other than above 0
15 GDoor mirror RH mirror
motor LEFT signalOutputWhen door mirror
RH mirror motor
operationLEFT Battery voltage
Other than above 0
16 W/LDoor mirror LH mirror
motor RIGHT or DOWN
signalOutputWhen door mirror LH
mirror motor opera-
tionRIGHT or DOWN Battery voltage
Other than above 0
18 OChangeover switch
LH signalInputWhen changeover
switch positionLH 0
Other than above 5
19 L Mirror switch DOWN signal InputWhen mirror switch
positionDOWN 0
Other than above 5
20 BR Mirror switch RIGHT signal inputWhen mirror switch
positionRIGHT 0
Other than above 5
21 SBDoor mirror RH sensor
horizontal signalInputWhen door mirror
RH mirror face posi-
tionClose to left edge 3.5
Close to right edge 0.5
22 O/LDoor mirror LH sensor
horizontal signalInputWhen door mirror LH
mirror face positionClose to left edge 0.5
Close to right edge 3.5
26 P UART LINE (RX)Input/
OutputTilt switch operated
30 GRDoor mirror LH mirror
motor RIGHT or DOWN
signalOutputWhen door mirror LH
mirror motor opera-
tionRIGHT or DOWN Battery voltage
Other than above 0
SKIA0175E
SKIA0175E

GW-104
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
Terminals and Reference Values for Driver Seat Control UnitNIS00237
31 BRDoor mirror LH mirror
motor UP signalOutputWhen door mirror LH
mirror motor opera-
tionUP Battery voltage
Other than above 0
32 VDoor mirror LH mirror
motor LEFT signalOutputWhen door mirror LH
mirror motor opera-
tionLEFT Battery voltage
Other than above 0
33 W Mirror sensor power supply Output — Battery voltage
34 R Power supply (fuse) Input — Battery voltage
39 L Power supply (fusible link) Input — Battery voltage
40 B Ground (signal) — — 0
41 Y Sensor ground — — 0
48 B Ground (power) — — 0 Te r -
minalWire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
Te r m i -
nal Wire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
1 R/G UART LINE (RX)Input/
OutputTilt switch operated
3 L CAN-HInput/
Output——
17 W/R UART LINE (TX)Input/
OutputTilt switch operated
19 P CAN-LInput/
Output——
32 B/W Ground (signal) — — 0
33 W Power supply (fusible link) Input — Battery voltage
40 B/W Power supply (fuse) Input — Battery voltage
48 B/W Ground (power) — — 0
SKIA0175E
SKIA0175E

GW-106
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
Display Item List
Work Flow NIS00239
1. Check the symptom and customer's requests.
2. Understand the system description. Refer to GW-94, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to GW-106,
"Symptom Chart"
4. Does reverse interlock door mirror system operate normally?
Yes , GO TO 5.
No, GO TO 3.
5. INSPECTION END
Symptom ChartNIS0023A
Test item Description
MIRROR MOTOR RHThe RH mirror motor moves the mirror UP/DOWN and LEFT/RIGHT by receiving the drive
signal.
MIRROR MOTOR LHThe LH mirror motor moves the mirror UP/DOWN and LEFT/RIGHT by receiving the drive
signal.
Symptom Diagnoses / service procedureReference
page
Reverse interlock door mirror does not operate.1. Check seat set switch circuitSE-81
2. Check changeover switch circuitGW-107
3. Check mirror switch circuitGW-109
4. Check A/T control device R position signal circuitGW-117
5. Check mirror motor circuitG W - 111
6. Check mirror sensor circuitGW-114
7. Replace automatic drive positioner control unitSE-11

At reverse interlock door mirror system operation, mirror
angle is not in the setting position

After finishing the reverse interlock door mirror system.
Operation, mirror angle does not return to the original posi-
tion1. Check mirror sensor circuitGW-1142. Check A/T control device R position signal circuitGW-117
3. Replace automatic drive positioner control unitSE-11
None of the door mirror can be operated using mirror switch. Check mirror switch circuitGW-109
A part of the remote control door mirror does not operated.1. Check mirror switch circuitGW-1092. Check door mirror circuitGW-109
Mirror remote control switch can not be switched right and left.1. Check changeover switch circuitGW-1072. Check mirror switch circuitGW-109

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-111
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
4. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit connector.
2. Turn ignition switch ON.
3. Check voltage between automatic drive positioner control unit and ground.
OK or NG
OK >> Check the condition of harness and connector.
NG >> Replace automatic drive positioner control unit.
Check Mirror Motor Circuit NIS0023D
1. CHECK MIRROR MOTOR FUNCTION
With CONSULT-II
Check the operation with (MIRROR MOTOR RH, MIRROR MOTOR LH) in the ACTIVE TEST.
Without CONSULT-II
1. Turn ignition switch to ON position.
2. Check voltage between door mirror connector and ground.
OK or NG
OK >> Mirror motor circuit is OK.
NG >> GO TO 2.
Terminals
Voltage (V)
(Approx.) (+)
(-) Automatic drive
positioner control
unit connectorTerminal
M63
Ground 5 4
19
20
PIIB6019E
Test item Description
MIRROR MOTOR LHThe LH mirror motor moves the mirror UP/DOWN and
LEFT/RIGHT by receiving the drive signal.
MIRROR MOTOR RHThe RH mirror motor moves the mirror UP/DOWN and
LEFT/RIGHT by receiving the drive signal.
PIIB6022E
Te r m i n a l s
Mirror switch
ConditionVoltage (V)
(Approx.) (+)
(–)
Door mirror
connectorTerminal
D2 (RH)
D39 (LH)5
GroundUP Battery voltage
Other than above 0
6LEFT Battery voltage
Other than above 0
7DOWN / RIGHT Battery voltage
Other than above 0
PIIB6031E

IDX-2
ALPHABETICAL INDEX
Symbols
(VK45DE) .............................................................. GI-6
(VQ35DE) ............................................................. GI-6
A
A/C air flow ...................................................... ATC-37
A/C component layout ..................................... ATC-25
A/C compressor mounting ........... ATC-153, ATC-157,
ATC-158
, ATC-159, ATC-161, ATC-163, ATC-164,
ATC-166
, ATC-167, ATC-168
A/C compressor precaution ............................. ATC-12
A/C compressor special service tool ................ ATC-16
A/C control operation (auto A/C) ...................... ATC-33
A/C diagnostic work flow (auto A/C) .............. ATC-110
A/C evaporator ............................................... ATC-167
A/C HFC134a (R134a) system precaution ........ ATC-6
A/C HFC134a (R134a) system service procedure .......
ATC-150
A/C HFC134a (R134a) system service tools ... ATC-17
A/C HFC134a system service equipment precaution ...
ATC-13
A/C lubricant (R134a) ...................................... ATC-26
A/C lubrication oil ........................................... ATC-173
A/C operational check ...................................... ATC-65
A/C self-diagnoses (auto A/C) ........ ATC-56, ATC-110
A/C service data specification ........................ ATC-173
A/C system description (auto A/C) ................... ATC-29
A/C trouble diagnoses (auto A/C) .................... ATC-40
A/C, A - Wiring diagram ................................... ATC-46
A/T fluid checking ...................... AT-13, AT-53, MA-29
A/T fluid cooler cleaning .................................... AT-14
A/T fluid replacement ............................. AT-12, MA-31
A/T fluid temperature sensor ........................... AT-135
A/T IND - Wiring diagram .................................... DI-56
A/T self-diagnoses ............................... AT-92, AT-103
A/T shift lock system ........................................ AT-229
A/T shift lock system - Wiring diagram ............ AT-230
A/T trouble diagnoses ........................................ AT-44
Accelerator control system ............................... ACC-3
Accelerator pedal position (APP) sensor ........ EC-617,
EC-624
, EC-638, EC-1336, EC-1343, EC-1357
Accelerator pedal released position learning .... EC-86,
EC-788
AF1B1-Wiring diagram ...... EC-237, EC-246, EC-255,
EC-265
, EC-648, EC-950, EC-959, EC-968, EC-978,
EC-1367
AF1B2-Wiring diagram ...... EC-239, EC-248, EC-257,
EC-267
, EC-650, EC-952, EC-961, EC-970, EC-980,
EC-1369
AF1HB1-Wiring diagram .................... EC-171, EC-884
AF1HB2-Wiring diagram .................... EC-173, EC-886
Air bag .............................................................. SRS-3
Air bag precautions ........................................... SRS-3
Air cleaner and air duct(VK45DE) ................... EM-177
Air cleaner and air duct(VQ35DE) .................... EM-19
Air cleaner filter replacement ............................ MA-25
Air cleaner filter replacement(VQ35DE) ........... MA-18
Air cleaner filter(VQ35DE) ................................ EM-20
Air conditioner cut control ................... EC-35, EC-737
Air flow meter - See Mass air flow sensor ....... EC-193,
EC-202
, EC-906, EC-915
Air fuel ratio sensor 1 ......... EC-234, EC-244, EC-253,
EC-262
, EC-646, EC-947, EC-957, EC-966, EC-975,
EC-1365
Air fuel ratio sensor 1 heater ............. EC-170, EC-883
Air mix. door motor ......................... ATC-82, ATC-140
Ambient sensor ............................. ATC-112, ATC-125
Angular tightening application ............................. EM-7
Angular tightening application(VK45DE) ........ EM-165
APPS1 - Wiring diagram ................. EC-619, EC-1338
APPS2 - Wiring diagram ................. EC-626, EC-1345
APPS3 - Wiring diagram ................. EC-640, EC-1359
ASC/BS - Wiring diagram ............... EC-578, EC-1291
ASC/SW - Wiring diagram .............. EC-561, EC-1274
ASCBOF - Wiring diagram .............. EC-658, EC-1378
ASCD .................................................. EC-36, EC-738
ASCD (automatic speed control device) ........... ACS-3
ASCIND - Wiring diagram ............... EC-665, EC-1385
AT indicator lamp ................................................ DI-55
Auto air conditioner - Wiring diagram ............. ATC-46
Auto amp ...................................................... ATC-124
Auto anti-dazzling inside mirror .......... GW-69, GW-70
Automatic amplifier ........... ATC-54, ATC-67, ATC-124
Automatic transmission fluid replacement ........ MA-32
AWD - Wiring diagram ....................................... TF-17
Axle ................................................................... MA-37
B
Back-up lamp ................................................... LT-245
Basic inspection .................................. EC-78, EC-780
Battery ................................................................. SC-4
Battery current sensor ....... EC-524, EC-531, EC-538,
EC-545
, EC-1237, EC-1244, EC-1251, EC-1258
Battery/Starting/Charging System Tester SC-7, SC-11,
SC-25
BCM (Body control module) .............................. BCS-3
Block heater(VK45DE) .................................... EM-252
Block heater(VQ35DE) ................................... EM-124
Blower motor ................................... ATC-88, ATC-131
Blower unit .................................................... ATC-129
Brake fluid level ................................................ MA-35
Brake hydraulic line ........................................... BR-11
Brake inspection ............................................... MA-36
Brake lines and cables inspection .................... MA-35
Brake pedal .......................................................... BR-6
Brake switch ................................... EC-589, EC-1307
BRK/SW - Wiring diagram .............. EC-591, EC-1309
Bulb specifications ........................................... LT-313
Bumper, front ...................................................... EI-11
Bumper, rear ....................................................... EI-14
C
Camshaft inspection(VK45DE) ....................... EM-217
Camshaft inspection(VQ35DE) ......................... EM-87

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Camshaft position sensor (PHASE) EC-371, EC-1082
Camshaft(VK45DE) ......................................... EM-215
Camshaft(VQ35DE) ........................................... EM-85
CAN .................................................................. DI-109
CAN - Wiring diagram .......... EC-162, EC-866, AT-106
CAN (Controller Area Network) ... SB-5, BL-26, BL-59,
BL-221
, GW-19, GW-73, GW-95, SE-16
CAN communication ........... EC-161, EC-164, EC-740,
EC-865
, EC-868, AT-32, AT-105, TF-13, TF-32, SB-5,
BL-26
, BL-59, BL-221, GW-19, GW-73, GW-95, SE-16,
WW-11
Canister-See EVAP canister ............... EC-42, EC-744
Center bearing assembly (propeller shaft) ........ PR-12
Center bearing disassembly (propeller shaft) .... PR-11
CHARGE - Wiring diagram ................................ SC-22
Charging system ................................................ SC-20
Chassis and body maintenance ........................ MA-29
CHIME - Wiring diagram ..................................... DI-63
CIGAR - Wiring diagram .................................. WW-50
Cigarette lighter ............................................... WW-50
Circuit breaker ................................................... PG-17
Clock ................................................................. DI-107
CLOCK - Wiring diagram .................................. DI-107
Closed loop control .............................. EC-32, EC-734
Closed loop control (Bank 1) ........... EC-496, EC-1211
Closed loop control (Bank 2) ........... EC-496, EC-1211
Collision diagnosis ........................................... SRS-54
Combination lamp, front, removal and installation ........
LT-75
Combination lamp, rear, removal and installation ........
LT-265
Combination meter ............................................... DI-5
COMPAS - Wiring diagram ............................... DI-105
Compass .......................................................... DI-102
Component Location (auto A/C) ...................... ATC-42
Compression pressure(VK45DE) .................... EM-235
Compression pressure(VQ35DE) .................... EM-102
Compressor special service tool ...................... ATC-16
Condenser ..................................................... ATC-164
Connecting rod bearing clearance(VK45DE) .. EM-275
Connecting rod bushing clearance .................. EM-143
Connecting rod bushing clearance(VK45DE) .. EM-271
Connecting rod(VK45DE) ................................ EM-271
Connecting rod(VQ35DE) ................................ EM-141
CONSULT-II Reference value (A/T) .................. AT-90
Control units (terminal arrangement) ............... PG-107
Control valve (A/T) ............................................. AT-38
Controller Area Network (CAN) ... SB-5, BL-26, BL-59,
BL-221
, GW-19, GW-73, GW-95, SE-16
Converter housing installation ............ AT-277, AT-280
COOL/F - Wiring diagram ................ EC-502, EC-1217
Coolant replacement(VQ35DE) ......................... MA-15
Cooling circuit (engine)(VK45DE) ...................... CO-38
Cooling circuit (engine)(VQ35DE) ....................... CO-9
Cooling fan motor ............................ EC-509, EC-1224
Cooling fan(VK45DE) ........................................ CO-51
Cooling fan(VQ35DE) ........................................ CO-22
Cowl top ............................................................... EI-18
Cowl top cover ..................................................... EI-18
Crankcase ventilation system - See Positive crankcase
ventilation ............................................. EC-51
, EC-753
Crankshaft position sensor (POS) ... EC-364, EC-1075
Crankshaft(VK45DE) ...................................... EM-253
Crankshaft(VQ35DE) ...................................... EM-141
Crash zone sensor .......................................... SRS-49
CUR/SE - Wiring diagram .. EC-526, EC-533, EC-540,
EC-547
, EC-1239, EC-1246, EC-1253, EC-1260
Cylinder block boring(VK45DE) ...................... EM-274
Cylinder block(VK45DE) ................................. EM-252
Cylinder block(VQ35DE) ................................. EM-124
Cylinder head bolt tightening(VK45DE) .......... EM-237
Cylinder head bolt tightening(VQ35DE) .......... EM-105
Cylinder head(VK45DE) ................................. EM-235
Cylinder head(VQ35DE) ................................. EM-102
D
D/LOCK - Wiring diagram .................................. BL-28
Daytime light system ........................................... LT-78
Daytime running light - See Daytime light system LT-78
DEF - Wiring diagram ............................ SB-7, SE-119
Diagnosis sensor unit ..................................... SRS-52
Diagnostic trouble code (DTC) for OBD system EC-16,
EC-59
, EC-718, EC-761
Direct clutch solenoid valve ............... AT-155, AT-157
Display and amp.assembly ............... ATC-54, ATC-67
Door glass ........................................... GW-61, GW-65
Door glass Fitting Adjustment(Front) ................ GW-64
Door glass Fitting Adjustment(Rear) ................. GW-68
Door lock .......................................................... BL-194
Door mirror ...................................................... GW-118
Door trim ............................................................. EI-34
Door, front ........................................... BL-188, GW-61
Door, rear ............................................ BL-188, GW-65
Drive belt inspection ......................................... MA-22
Drive belt(VK45DE) ........................................ EM-174
Drive belt(VQ35DE) .......................................... EM-16
Drive shaft ......................................................... MA-38
Drive shaft (rear) ............................................... RAX-8
Driver air bag .................................................. SRS-42
DTRL - Wiring diagram ....................................... LT-83
Duct and grilles .............................................. ATC-143
E
ECM power supply EC-154
, EC-479, EC-858, EC-1186
ECM/PW - Wiring diagram ............... EC-480, EC-1187
ECTS - Wiring diagram ...................... EC-216, EC-928
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-604, EC-615,
EC-1322
, EC-1334
Electric throttle control actuator (VK45DE) ..... EM-179
Electric throttle control actuator (VQ35DE) ....... EM-21
Electrical load signal circuit .............. EC-667, EC-1387
Electrical unit ................................................... PG-107
Electrical units location ...................................... PG-98
Electronic ignition (EI) system ............. EC-33, EC-735
Engine control module (ECM) .......... EC-483, EC-1190

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
EC-890
Heated seat ..................................................... SE-144
Heater and cooling unit (Heater core) ........... ATC-134
HFC134a (R134a) system precaution ............... ATC-6
HFC134a (R134a) system service procedure ATC-150
HFC134a (R134a) system service tools .......... ATC-17
HFC134a system service equipment precaution ..........
ATC-13
High and low reverse clutch solenoid valve .... AT-159,
AT-161
Hood ................................................................... BL-15
Horn ................................................................. WW-54
HORN - Wiring diagram ................................... WW-54
How to erase DTC for OBD system ..... EC-68, EC-770
HSEAT - Wiring diagram ................................. SE-147
I
IATS - Wiring diagram ....................... EC-211
, EC-923
ICC - Wiring diagram ....................................... ACS-23
ICC/BS - Wiring diagram ................. EC-569, EC-1282
ICC/SW - Wiring diagram ................ EC-554, EC-1267
ICCBOF - Wiring diagram ................ EC-684, EC-1404
Idle air volume learning ....................... EC-86, EC-788
Idle speed .............................. EC-78, EC-780, EC-785
Idle speed control (ISC) .... EC-470, EC-472, EC-1177,
EC-1179
Ignition coil ....................................... EC-691, EC-1411
Ignition coil(VK45DE) ...................................... EM-190
Ignition coil(VQ35DE) ........................................ EM-44
Ignition control system ..................... EC-691, EC-1411
Ignition timing ........................ EC-78, EC-780, EC-785
IGNSYS - Wiring diagram ................ EC-692, EC-1412
Illumination ....................................................... LT-293
Illumination control ................. LT-289, LT-290, LT-291
In vehicle sensor ........................... ATC-115, ATC-126
INJECT - Wiring diagram ................. EC-670, EC-1390
Injector ............................................................. EC-669
Input clutch solenoid valve ................. AT-147, AT-149
Instrument panel .................................................. IP-10
Intake air temperature sensor ........... EC-209, EC-229,
EC-922
, EC-942
Intake door control linkage adjustment ............ ATC-87
Intake door motor ........................... ATC-85, ATC-132
Intake manifold collector(VQ35DE) ................... EM-21
Intake manifold(VK45DE) ................................ EM-179
Intake manifold(VQ35DE) .................................. EM-26
Intake sensor ................................ ATC-121, ATC-128
Intake valve timing control (Bank 1) .. EC-166, EC-870
Intake valve timing control (Bank 2) .. EC-166, EC-870
Intake valve timing control position sensor (Bank 1) ....
EC-1203
Intake valve timing control position sensor (Bank 2) ....
EC-1203
Intake valve timing control solenoid valve (Bank 1) ......
EC-185
, EC-899
Intake valve timing control solenoid valve (Bank 2) ......
EC-185
, EC-899
Integrated homelink transmitter ........................ BL-278
Intelligent cruise control (ICC) system .............. ACS-6
Interior ................................................................. EI-37
Interior lamp ...................................................... LT-266
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-18
IVCB1 - Wiring diagram ..................... EC-186, EC-900
IVCB2 - Wiring diagram ..................... EC-188, EC-902
IVCSB1 - Wiring diagram ............................... EC-1204
IVCSB2 - Wiring diagram ............................... EC-1206
IVTB1 - Wiring diagram ................................... EC-873
IVTB2 - Wiring diagram ................................... EC-875
K
Knock sensor (KS) ........................... EC-359
, EC-1070
KS - Wiring diagram ......................... EC-360, EC-1071
L
LAN system circuit ........................................... ATC-71
Lane Departure Warning System ....................... DI-75
Laser beam aiming adjustment ....................... ACS-15
Latch (lower anchors and tether for children) system ...
SB-35
LDW .................................................................... DI-75
LDW - Wiring Diagram ........................................ DI-86
License lamp ..................................................... LT-248
Line pressure solenoid valve ........................... AT-130
Line pressure test (A/T) ..................................... AT-55
Liquid gasket application .................................... EM-8
Liquid gasket application(VQ35DE) LU-3, LU-23, CO-3
Location of electrical units ................................. PG-98
Low coast brake solenoid valve ......... AT-163, AT-165
Lubricant (R134a) A/C ..................................... ATC-26
Lubrication circuit (engine)(VK45DE) ................ LU-25
Lubrication circuit (engine)(VQ35DE) .................. LU-5
Lubrication oil A/C .......................................... ATC-173
M
MAFS - Wiring diagram ..... EC-196
, EC-204, EC-909,
EC-917
Magnet clutch .................................................. ATC-93
MAIN - Wiring diagram ........ EC-154, EC-858, AT-180
Maintenance (engine)(VQ35DE) ...................... MA-14
Major overhaul (Final drive) .............. FFD-15, RFD-18
Major overhaul (Transfer) .................................. TF-45
Malfunction indicator lamp (MIL) .......... EC-70, EC-772
Manual mode switch ........................................ AT-167
Mass air flow sensor (MAFS) ............ EC-193, EC-202,
EC-906
, EC-915
Meter ..................................................................... DI-5
METER - Wiring diagram .................................... DI-13
MIL data link connectors circuit ....... EC-714, EC-1438
MIL/DL - Wiring diagram .................. EC-714, EC-1438
MIRROR - Wiring diagram ................................ GW-97
Mirror, door ..................................................... GW-118
Mirror, out side ................................................ GW-118
Misfire .............................................. EC-349, EC-1061