Page 226 of 1226
206-04-2 Rear Disc Brake 206-04-2
SPECIFICATIONS
Lubricants, Fluids, Sealers and Adhesives
Item Specification
ESD-M6C57-A
Brake Disc S~ecification
I Description I mm I
Brake disc diameter
New brake disc nominal thickness
I Worn brake pad discard thickness* I 1.50 1
280
10.15
Worn brake disc discard thickness*
Maximum brake disc thickness variation
I Brake caliper piston diameter I 34 I
8
0.02
I *When the discard thickness has been reached, install a new brake disdbrake pads.
-spindle retaining bolts I 66 I 49 I - I
Torque Specifications
I Brake caliper anchor plate retaining bolts I 60 I 44 I - I
I Brake caliper retaining bolts I 35 I 26 I - I
Ib-in Item
I Brake.tube to brake caliper union I 15 I 11 I - I
2006.0 Fiesta 1u2oo6 G427692en
Nm Ib-ft
procarmanuals.com
Page 230 of 1226

206-04-6 Rear Disc Brake 206-04-6
REMOVAL AND INSTALLATION
Brake Pads(l2 238 0)
Special Tool(s) Detach the brake caliper from the brake (
I Retractor, Rear Brake Caliper I caliper anchor plate.
Piston
206-0
1 2
Materials
Name Specification
Removal 5. Remove the brake pads.
Brake Fluid - Super
I DOT4
A CAUTI0N:lf brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
ESD-M6C57-A
1. Release the parking brake.
2. Remove the wheel and tire.
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires, Removal
and Installation).
3. Detach the brake hose from the brake hose
support bracket.
Installation
1. CAUTIONS:
n~hen the brake caliper piston is retracted
into the brake caliper piston housing, brake
fluid will be displaced into the brake fluid
reservoir.
Asupport the brake caliper during brake
caliper piston retraction.
4m ACAUTION:S~~~~~~ the brake caliper to
prevent load being placed on the brake hose.
2006.0 Fiesta 1212006 G427695en
procarmanuals.com
Page 231 of 1226
206-0417 Rear Disc Brake 206-0417
REMOVAL AND INSTALLATION
Using the special tool, retract the brake
caliper piston.
2. N0TE:Make sure that the brake pad contact
points are clean and free from contamination.
To install, reverse the removal procedure.
3. Fully depress and release the brake pedal.
4. Check the fluid level in the brake fluid
reservoir and top up
if necessary with brake
fluid.
2006.0 Fiesta 1212006 G427695en
procarmanuals.com
Page 232 of 1226

206-04-8 Rear Disc Brake 206-04-8
REMOVAL AND INSTALLATION
Brake Caliper(l2 253 0) f
Special Tool(s) 4. Using a brake hose clamp, clamp the brake (
I Retractor, Rear Brake Caliper I hose.
General Equipment
I Brake hose clamp I
Materials
Name Specification
Brake Fluid - Super ESD-M6C57-A
DOT4 5n ~CAUTION:C~~ the brake hose to prevent
fluid loss or dirt ingress.
Removal Disconnect the brake tube from the brake
caliper.
A CAUTI0N:If brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
I. Release the parking brake.
2. Remove the wheel and tire.
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires, Removal
and Installation).
3. Detach the parking brake cable from the
brake caliper.
I. Pull back the brake caliper lever.
2. Disconnect the parking brake cable from the
brake caliper lever.
6. Detach the brake caliper from the brake
3. Detach the parking brake cable from the caliper anchor plate.
brake caliper.
2006.0 Fiesta 1212006 G427696en
procarmanuals.com
Page 256 of 1226
206-06-2 Hydraulic Brake Actuation 206-06-2
SPECIFICATIONS
Lubricants. Fluids. Sealers and Adhesives
Torque Specifications
Item
Super DOT 4 brake fluid
I Description I Nm I Ib-ft I Ib-in I
Specification
ESD-M6C57-A
I Brake master cylinder brake tube unions I 17 I 13 I - I
I Brake master cylinder retaining nuts I 25 I 18 I - I
Pressure conscious reducing valve unions
-- - -
I Brake pedal cross-shaft mounting bracket nuts I 25
2006.0 Fiesta 1212006 G327704en
26 19 -
procarmanuals.com
Page 262 of 1226

206-06-8 Hydraulic Brake Actuation 206-06-8
REMOVAL AND INSTALLATION
Brake Master Cylinder - RHD(12 343 0)
Removal 4. Tighten the bleed nipple. \,
All vehicles
CAUTI0N:lf brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
I. Disconnect the brake vacuum pipe from the
brake booster.
I. Unclip the brake vacuum pipe.
2. Disconnect the brake vacuum pipe.
6. Install the brake fluid reservoir cap.
7m &AUTION:C~~ the brake tubes to prevent
fluid loss or dirt ingress.
Disconnect the brake tubes from the brake
master cylinder.
2. Disconnect the battery ground cable. For
additional information, refer to
Section
414-01 [Battery, Mounting and
Cables].
3. Remove the windshield wiper motor
assembly. For additional information, refer
to Section
501 -1 6 [Wipers and Washers].
4m &AUTION:T~~ brake fluid reservoir cap
must not become contaminated.
Vehicles with anti-lock brakes
Remove the brake fluid reservoir cap.
5. N0TE:lt will be necessary to carry out this 8m &AUTION:C~~ the brake tubes to prevent
fluid loss or dirt ingress.
step on both sides in order to completely
drain the brake fluid reservoir.
Drain the brake fluid reservoir.
1. Connect one end of a suitable piece of clear
plastic pipe to the bleed nipple and place the
other end into a suitable container.
2. Loosen the bleed nipple.
3. Depress the brake pedal until all the fluid is
drained from the brake fluid reservoir.
2006.0 Fiesta 1212006 ~89191 en
procarmanuals.com
Page 263 of 1226
206-0619 Hydraulic Brake Actuation 206-0619
REMOVAL AND INSTALLATION
Disconnect the brake tubes from the brake 11. Disconnect the low brake fluid warning
master cylinder. indicator switch electrical connector.
I
All vehicles
9m &AUTION:C~~ the clutch master cylinder
feed hose to prevent fluid loss or dirt
ingress.
Disconnect the clutch master cylinder feed
hose from the brake fluid reservoir.
12. Remove the brake master cylinder and
brake fluid reservoir assembly.
Installation
A CAUTI0N:Make sure the brake master
cylinder vacuum seal is correctly
positioned before installation.
I. To install, reverse the removal procedure.
2. Bleed the brake system. For additional
information, refer to Section
206-00 [Brake
System
- General Information].
10. Detach the brake master cylinder from the
brake booster.
2006.0 Fiesta 1212006 G89191 en
procarmanuals.com
Page 276 of 1226
206-09A-2 Anti-Lock Control 206-09A-2
SPECIFICATIONS
Lubricants, Fluids, Sealers and Adhesives
Specificat
1 ions I
I Super DOT 4 brake fluid
Hydraulic control unit (HCU) to support bracket
retaining bolts
I Wheel speed sensor retaining bolts I 9 I - I 80 I
HCU support bracket retaining bolts
Brake tube to HCU unions
I Anti-lock brake system (ABS) module to HCU I 5 I - I 44 I
I retaining bolts
20
18
2006.0 Fiesta 1212006 GII 2960en
15
13 -
-
procarmanuals.com