2007 FORD FIESTA wiring

303-00-1 5 Engine System - General Information 303-00-1 5
DIAGNOSIS AND TESTING
N0TE:The varying design of compression checking
% devices and fluctuating starter motor speeds
normally only allows for a comparison to be made
of the compression pressures in all cylinders.
Measure the compression pressure
Engine
- 1.4L Duratorq-TDCi (DV)
biesel)
1. Remove the air cleaner.
REFER to: Air Cleaner
- 1.4L Duratorq-TDCi
(DV) Diesel (303-12 Intake Air Distribution and
Filtering, Removal and
Installation). 4. Detach the exhaust gas recirculation (EGR) tube
from the cylinder block and from the EGR valve
(if equipped).
I I 2. Disconnect the fuel injector wiring harness main
connector. 5. Detach the EGR tube from the EGR cooler (if
equipped).
3. Disconnect the glow plug relay electrical
connector.
6. Remove the EGR tube from the intake manifold
assembly.
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-00-1 7 Engine System - General Information 303-00-1 7
DIAGNOSIS AND TESTING
14. N0TE:Check the EGR tube O-ring seal.
Install a new seal
if necessary. I
, Install the EGR tube to the intake manifold
assembly.
18 Connect the fuel injector wiring harness main
connector.
19 Install the air cleaner.
REFER to: Air Cleaner
- 1.4L Duratorq-TDCi
15 Attach the EGR tube to the cylinder block and (DV) Diesel (303-12 Intake Air Distribution
and
to the EGR valve (if equipped). Filtering, Removal
and Installation).
Using worldwide diagnostic system (WDS), clear
the fault codes from the PCM.
Measure the compression pressure
Engine
- 1.6L Duratorq-TDCi (DV)
biesel)
WARNINGS:
A Do not smoke or carry lighted tobacco or
open flame of any type when working on
or near any fuel related components.
Highly flammable mixtures are always
16 Attach the EGR tube to the EGR cooler (if present and can ignite. Failure to follow
equipped). these instructions may result in personal
injury.
Do not carry out any repairs to the fuel
injection system without checking that the
fuel pressure has dropped to zero and that
the fuel temperature has either reached
ambient temperature or is below
30' C,
whichever is the greater. Failure to follow
these instructions may result in personal
injury.
I. Using datalogger in world wide diagnostic
system (WDS), check that the fuel pressure has
dropped to zero and that the fuel temperature
17. Connect the glow plug relay electrical connector. has
either reached ambient temperature or is
below 30°C, whichever is the greater.
2. Raise and support the vehicle. REFER to:
(1 00-02 Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll.4L
303-01A-I 9 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-OIA-I 9
IN-VEHICLE REPAIR
Intake Manifold(21 183 0)
Removal 6. Remove the intake manifold lower retaining
bolt.
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable mixtures
are always present and may ignite. Failure
to follow these instructions may result in
personal injury.
1. Release the fuel system pressure. For
additional information, refer to
Section
31 0-00 [Fuel System - General
Information].
2. Disconnect the battery ground cable. For
additional information, refer to
Section
414-01 [Battery, Mounting and 7. Disconnect the engine wiring harness
Cables]. electrical connector.
3. Remove the air cleaner. For additional
information, refer to Section
303-1 2 [Intake
Air Distribution and Filtering].
4. Detach the power steering fluid reservoir
from the bracket and position
it to one side.
5. Remove the accessory drive belt. For
additional information, refer to
Section
303-05 [Accessory Drive].
8. Disconnect the positive crankcase ventilation
(PCV) hose from the PCV.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll14L
Duratec-1 6V (Sigma)ll16L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
15. Disconnect the generator electrical 17. Disconnect the fuel injector electrical
connector. connectors and
position it with the engine
i wiring harness to one side.
16. Detach the generator from the engine.
1. Remove the bolts.
2. Remove the nut and the stud.
18. Disconnect the engine coolant temperature
(ECT) sensor electrical connector.
2006.0 Fiesta 1~12006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
19. Disconnect the fuel supply line quick Discard the O-ring seals.
release coupling. For additional
information, refer to Section
31 0-00 [Fuel
System
- General Information].
20. Disconnect the fuel return line quick release
coupling. For additional information, refer
to Section
31 0-00 [Fuel System - General
Information].
21. Detach the fuel line from the intake
manifold and position
it to one side.
Remove the cable tie.
22.
Remove the fuel supply manifold.
23. Detach the wiring harness and the coolant
hose from the intake manifold.
24. Detach the wiring harness from the intake
manifold.
25. Remove the intake manifold.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Dura
303-01 A-23 Duratec-1
6V (Sigma)ll .(
:ec-I 6V (Sigma)llm4L
L
Duratec-1 6V (Sigma)
303-01 Am23
IN-VEHICLE REPAIR
Discard the gaskets.
Installation
3. Attach the wiring harness and the coolant
hose to the intake manifold.
4. N0TE:lnstall new injector O-ring seals.
1. N0TE:lnstall new intake manifold gaskets. N0TE:Coat the 0-rina seals with clean enaine oil.
Install the intake manifold. V "
Install the fuel supply manifold.
2. Attach the wiring harness to the intake
manifold. 5. Connect the fuel return line quick release
coupling. For additional information, refer to
Section
31 0-00 [Fuel System - General
Information].
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-26 Duratec-1 6V (Sigma)Il.GL Duratec-1 6V (Sigma) 303-01 A-26
IN-VEHICLE REPAIR
16. Connect the evaporate emission (EVAP)
hose to the EVAP valve.
17. Connect the brake booster vacuum line to
the intake manifold.
19. Connect the engine wiring harness
electrical connector.

20. Install the intake manifold lower retaining
bolt and the generator bracket retaining
bolts.
18. Connect the positive crankcase ventilation
(PCV) hose to the PCV.
21. Install the accessory drive belt. For
additional information, refer to
Section
303-05 [Accessory Drive].
22. Attach the power steering fluid reservoir to
the bracket.
23. Install the air cleaner. For additional
information, refer to Section
3031 2 [Intake
Air Distribution and Filtering].
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-56 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-56
IN-VEHICLE REPAIR
15. Disconnect the evaporative emissions 18. Disconnect the fuel supply line quick
(EVAP) hose from the EVAP valve.
release coupling.
f
16. Disconnect the engine wiring harness
electrical connector.
17. Disconnect the EVAP valve electrical
connector. For
additional information, refer to: Quick
(..
Release Coupling (310-00 Fuel System -
General Information, General Procedures).
I 9. Disconnect the fuel return line quick release
coupling.
For additional information, refer to: Quick
Release Coupling
(31 0-00 Fuel System -
General Information, General Procedures).
20. Using the special tool, disconnect the
coolant hose from the coolant distribution
assembly.
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com