2006 SKODA FABIA technical data

Instruments and Indicator/Warning Lights19
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Using the system
The rocker switch and the button are located in the grip of the
window wiper lever ⇒fig. 6.
Selecting the memory
– Repeated short-term pressing of the button allows one to
select the individual memories.
Selecting the functions
– Press the rocker switch up or down. This will cause the indi-
vidual functions of the multi-functi onal indicator to appear in the
display one after the other.
Setting function to zero
– Select the memory you want.
– Press button for more than 1 second.
The following readouts of the selected memory will be set to zero by button :
•average fuel consumption,
•distance driven,
•average speed,
•Driving time.
You can only operate the multi-functional indicator when the ignition is switched on. After the ignition is switched on, the function displayed is the one which you last selected before switching off the ignition.
If the outside temperature drops below +4 °C, a snow flake symbol (warning signal for ice on the road) appears with the outside temperature indicator ⇒ fig. 7 and a warning signal* sounds for 10 seconds. The snoke flake symbol draws the attention of the driver to possible black ice formation. The display swicthes back after 10 seconds to the last selected function.
Outside temperature
Fig. 6 Multi-functional indicator: Control elements
AAAB
AB
AA
AB
AB
Fig. 7 Multi-functional indicator: the outside temperature
NKO A05Fabia 20.book Page 19 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights21
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Driving time
The driving time which has elapsed since the memory was last erased, appears in the display ⇒page 18. If you wish to calculate the driving time from a partic- ular time of day you must first erase th e memory at this moment in time by pressing the button ⇒page 19, fig. 6.
The maximum time indicated in both switch positions is 99 hours and 59 minutes. The indicator is set back to null if this period is exceeded.
Distance driven
The distance driven since the memory was last erased appears in the display ⇒ page 18. If you wish to calculate the distance driven from a particular time of day you must first erase the memory at this moment in time by pressing the button ⇒page 19, fig. 6.
The maximum distance indicated in both switch positions is 9999 km. The indi- cator is set back to null if this period is exceeded.
Average speed
The average speed since the memory was last erased is shown in the display in km/hour ⇒page 18. If you wish to determine the average speed over a certain period of time you must first erase the memory at the start of the new measure- ment using the button ⇒page 19, fig. 6.
A zero appears in the display for the first 100 m you drive after erasing the memory.
Information display*
Introduction
The information display provides you wi th information in a convenient way concerning the current operating state of your vehicle. The information system also provides you with data (depending on the equipment installed in the vehicle) relating to the radio, multi-functional indicator and navigation system.
Certain functions and operating conditio ns are always being checked on the vehicle when the ignition is switched on and also while driving.
Functional faults, if required repair wo rk and other information are indicated by red symbols ⇒page 24 and yellow symbols ⇒page 25.
Lighting up of these symbols is combin ed with an acoustic warning signal.
Information and texts giving warnings are also shown in the display ⇒ page 26.
AB
AB
AB
Fig. 8 Instrument cluster: Information display
NKO A05Fabia 20.book Page 21 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights23
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
After selecting the menu DISPLAY OFF the display is switched off. Press rocker switch for at least 1 second to switch the display on again.
The Information VEH. STATUSflashes in the menu if there is something which is not in proper order on the vehicle (e.g . warning of a low fuel level). The first warning will be displayed after switching over to VEH. STATUS. You can then display other operating conditions afterw ards using the rocker switch function (such as water level low).
Door, tailgate and bonnet ajar warning
The door, tailgate compartment door an d bonnet ajar warning lights up when at least one of the three items door, tai lgate or bonnet are not closed when the ignition is turned on. The symbol indica tes which door is still open or whether the tailgate or bonnet is not closed ⇒fig. 11.
The symbol goes out as soon as the d oors, tailgate and bonnet are completely closed.
As an additional warning signal, a 3 time peep sounds if the car is driven at a speed of more than 6km/hour and if the door or the tailgate is open.
Radio display
These displays appear in addition to the normal information in the radio display.
Auto Check Control
Car state
The Auto Check Control carries out a ch eck of certain functions and vehicle components. The check is performed consta ntly when the ignition is switched on, both when the vehicle is stat ionary, as well as when driving.
AA
Fig. 11 Information display: Door warning
Fig. 12 Information display: Radio display
NKO A05Fabia 20.book Page 23 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights25
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Three successive warning signals will sound if a red symbol appears.
If several operational faults of priority 1 exist, the symbols appear one after the other and are each illumi nated for about 5 seconds.
Ye l l o w s y m b o l s
A yellow symbol signals a warning.
The meaning of the yellow symbols:
One warning signal will sound if a yellow symbol appears.
If several operational faults of priority 2 exist, the symbols appear one after the other and are each illuminated for about 10 seconds.
Check the relevant function as soon as possible.
Navigation system*
The controls for the navigation system, radio, CD player are located in the centre console on both sides of the mo nitor screen. Navigation data is also shown in the information display of the instrument cluster.
Information and warning texts are displaye d preferentially when the navigation system is switched on.
Operation of the navigation system is described in separate operating instruc- tions to be found in the on-board literature.
Fig. 14 Information display: Fuel level low
Fuel level low⇒ page 31
Check engine oil level, engine oil sensor faulty⇒page 31
Brake pad worn⇒page 32
Washer fluid level low⇒page 32
NKO A05Fabia 20.book Page 25 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights27
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
WARNING
•If you do not pay attention to the warning lights coming on and the corresponding descriptions and warning notes, this may result in severe body injuries or major vehicle damage.
•The engine compartment of your car is a hazardous area. There is a risk of injuries, scalding, accidents and fire when working in the engine compartment, e.g. inspecting and replenishing oil and other fluids. It is also essential to observe all warnings ⇒page 198.
Note
•Arrangement of the indicator lights depends on the model and model version. The symbols shown in the following functional description are to be found as indicator lights in the instrument cluster.
•Operational faults are shown in the instrument cluster as red symbols (priority 1 - danger) or yellow symbols (priority 2 - warning).
Electrohydraulic power steering⇒ page 29
EPC fault light (petrol engine)⇒page 29
Glow plug system (diesel engine)⇒page 29
Turn signal system for vehicles towing a trailer*⇒ page 30
Coolant temperature/coolant level⇒page 30
Electronic immobiliser⇒page 31
Fuel reserve⇒page 31
Engine oil⇒page 31
Brake pad wear*⇒page 32
Open door*⇒page 32
Fluid level in windshield washer system*⇒page 32
Control system for exhaust⇒page 32
Traction control system (TCS)*⇒page 33
Tyre pressure*⇒page 33
Selector lever lock* (automatic gearbox)⇒page 33
Electronic stability programme (ESP)*⇒page 33
Antilock brake system (ABS)*⇒page 34
Brake system⇒page 34
Airbag system⇒page 35
Diesel particle filter* (diesel engine)⇒page 36
Seat belt warning light*⇒page 37
NKO A05Fabia 20.book Page 27 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights29
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
WARNING
f there is a fault in the cornering lights, the headlights are automatically lowered to the emergency position. Thus the illuminated length of the road is shortened. Drive carefully and have the car inspected immedi-ately by a specialist garage.
Electrohydraulic power steering 
The warning light  comes on for a few seconds when the ignition is switched on.
If the warning light after switching on th e ignition or when driving lights up continuously, a fault exists in th e electrohydraulic power steering.
•If the yellow warning light lights up, this indicates a partial or total failure of the power steering and the steering forces can be greater.
Further information ⇒page 170.
WARNING
Contact your specialist garage if the power steering is defective.
Note
•If the yellow warning light  goes out after starting the engine again and a short drive, it is not necessary to visit a specialist garage.
•If the battery has been disconnected and reconnected, the yellow warning light  comes on after switching on the igni tion. The warning light must go out after driving a short distance.
•There is no power-assisted steering support when the vehicle is being towed without the engine running or when the power-assisted steering is
defect. The vehicle is fully steerable ho wever. There is simply increased force required to turn the steering wheel.
EPC fault light  (petrol engine)
The  (Electronic Power Control) warning light comes on for a few seconds when the ignition is switched on.
There is a system fault in the engine control system if the warning light  does not go out or comes on or flashes while driving. The engine management system selects an emergency programme which enables you to drive to the nearest specialist garage by adopting a gentle style of driving.
The following text will be displayed in the information display*:
ENGINE FAULT WORKSHOP!
Glow plug system  (diesel engine)
The indicator light  lights up for a cold engine when switching on the ignition (pre-heat position) 2 ⇒page 104. Start the engine after the indicator light goes out.
The glow plug indicator light will come on for about 1 second if the engine is at a normal operating temperature or if the outside temperature is above +5°C. This means that you can start the engine right away.
There is a fault in the glow plug system if the indicator light  does not come on at all or lights up continuously. Contact a specialist garage as soon as possible to obtain professional assistance.
There is a system fault in the engine control system if the warning light  has started to flash while driving. The engi ne management system selects an emer-
NKO A05Fabia 20.book Page 29 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights31
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Electronic immobiliser 
Data is compared between the ignition key and the control unit when switching on the ignition. The indicator light  will light up for a few seconds when igni- tion key authorisation is confirmed.
The warning light will start flashing cont inuously if a non-authorised ignition key (for example the wrong ignition key) has been used. The engine cannot be started ⇒page 40.
It is only possible to start the engine of your car with a Genuine Škoda key with the matching code.
Fuel reserve 
The warning light  comes on, if the fuel level is still about 7 litres.
A peep sounds as an additional warning signal.
The following text will be displayed in the information display*:
PLEASE REFUEL
Engine oil 
The warning light  lights up red (low oil pressure)
The warning light comes on for a few seconds 2) when the ignition is switched on.
Stop the vehicle and switch the engine off if the warning light does not go off after the engine has started or flashes while driving. Check the oil level and top up with oil as necessary ⇒page 201.
3 peeps sound as an additional warning signal.
Do not continue your journey if for some reason it is not possible under the conditions prevailing to top up with oil. Keep the engine switched off and obtain professional assistance from a specialist garage, otherwise it could lead to severe engine damage.
Do not drive any further if the warning light flashes even if the oil is at the correct level. Do not run the engine no t at idling speed either. Contact the nearest specialist garage to obtain professional assistance.
The following text will be displayed in the information display*:
STOP OIL PRESS. ENGINE OFF! OWNER'S MANUAL!
The warning light  lights up yellow* (oil quantity too low)
If the warning light lights up yellow, the qu antity of oil in the engine is probably too low. Check as soon as pos sible the oil level or top up ⇒page 201 with engine oil.
A peep sounds as an additional warning signal.
The following text will be displayed in the information display*:
CHECK OIL LEVEL
The warning light will go out if the bonnet is left open for more than 30 seconds. If no engine oil has been replenished, th e warning light will come on again after driving about 100 km.
The warning light  flashes yellow* (engine oil level sensor faulty)
A fault on the engine oil level sensor is indicated additionally by an audible signal and the warning light coming on se veral times after the ignition has been switched on.
In this case have the engine inspecte d without delay by a specialist garage.2)The warning light  on vehicles fitted with information display does not come on after switching the ignition on, but only if a fault exists or the engine oil level is too low.
NKO A05Fabia 20.book Page 31 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights33
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Tr a c t i o n c o n t r o l system (TCS) *
The warning light  comes on for a few seconds when the ignition is switched on.
The warning light comes on when drivin g when a control cycle is activated.
The warning light will come on and remains on if the TCS is switched off or if there is a fault in the system.
The fact that the TCS system operates together with the ABS means that the TCS warning light will also come on if the ABS system is not operating properly.
If the warning light  comes on immediately after starting the engine, the TCS system can be switched off for technica l reasons. In this case, the TCS system can be switched on again by switching th e ignition on and off. If the warning light goes out, the TCS system is fully functional again.
Further information about the TCS ⇒page 166.
Note
If the battery has been disconnected and reconnected, the warning light  comes on after switching on the ignition . The warning light must go out after driving a short distance.
Tyre inflation pressure*
The warning light  lights up, if there is a substantial drop in inflation pressure in one of the tyres. Reduce the speed and check or correct as soon as possible the inflation pressure in the tyres ⇒page 214.
A peep sounds as an additional warning signal.
If the warning light flashes, there is a system fault. Visit the nearest specialist garage and have the fault rectified.
Further information about tyre pressure-control system ⇒page 171.
WARNING
•When the warning light  lights up, immediately reduce the speed and avoid sudden steering and brak e manoeuvres. Please stop the vehicle without delay at the nearest possible stop and inspect the tyres and their inflation pressures.
•Under certain circumstances (e.g. sporty style of driving, wintry or unpaved roads) the warning light  can be delayed or does not light up at all.
•The tyre inflation pressure-control system does not take away the responsability from the driver for the correct tyre inflation pressure.
Note
If the battery has been disconnected, the warning light  comes on after switching on the ignition. The warning light must go out after driving a short distance.
Selector lever lock*  (automatic gearbox)
If the warning light  lights up, operate the brake pedal. This is necessary, in order to be able to move the selector lever out of the position P or N.
Electronic stability programme (ESP)*
The warning light  comes on for a few seconds when the ignition is switched on.
NKO A05Fabia 20.book Page 33 Tuesday, September 26, 2006 8:38 AM