Page 233 of 299

If and when231
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a
If and when
Vehicle onboard tools*, spare wheel*,
puncture repair kit* and towing bracket
Location
The vehicle tools, the spare wheel and the removable towing
bracket ball coupling are stored in the luggage compartment.
Vehicle tool kit and removable ball coupling
The vehicle tool kit and removable towing bracket ball coupling are stored on
the right of the luggage compartment, behind a cover.
Spare wheel
The spare wheel is stored underneath the vehicle Ÿpage 232.
Caution
Make sure that the spare wheel / removed wheel and the tools are stored
safely in the luggage compartment.
Vehicle onboard tools*
The vehicle tools are stored in the luggage compartment, behind the side
cover on the right and are secured using a thumb screw Ÿfig. 152 . The
tool kit comprises the following items:
To ol b ox
44)
Screwdriver with hexagon socket in the handle for slackened wheel
bolts. The screwdriver blade is reversible. The screwdriver is in the wheel
bolt.
Towing eye, removable
Open jaw spanner 10 x 13 mm
Wire hook
44) for pulling off the centre cover and the wheel bolt caps
44)Optional equipment
Fig. 152 Storage of
vehicle tools
A1
A1
A2
A3
A4
A5
Page 234 of 299

If and when 232
Box spanner for wheel bolts
Jack. Before you return the jack to the tool box, you must fully wind in the
claw. The crank must then be folded tight against the side of the jack.
The removable towing bracket
44), the key for unlocking the sunroof in an
emergency44) and the anti-theft wheel bolt adaptor44) are stored next to the
vehicle tools.
Adapter for anti-theft wheel bolts
We recommend you carry the wheel bolt adapter
44) in the vehicle tool kit at
all times.
The code number of the anti-theft wheel bolt is stamped on the front of the
adapter. You will need this number to replace the adapter if lost. Make a note
the code number of the anti-theft wheel bolt and keep it in a safe place - but
not in your vehicle.
WARNING
•Do not use the hexagonal socket in the screwdriver handle to tighten
the wheel bolts. It is not suitable for tightening the bolts to the necessary
torque. This may cause an accident.
•The jack supplied by the factory is only designed for changing wheels
on this model. Never attempt to use it for lifting heavier vehicles or other
loads. Risk of injury.
•Use the jack only on firm, level ground.
•Never start the engine when you have raised the vehicle on the jack.
Risk of accident.
•Never place your body (e.g. arm or leg) underneath the vehicle if it is
only supported by the jack Risk of injury.
•If you have to work underneath the vehicle, you must use suitable
stands additionally to support the vehicle - Risk of accident!.
Taking out the spare wheel
1. Lift the cover Ÿfig. 153 located on the floor of the luggage
compartment, next to the tailgate lock.
2. Pull the ring of the rubber seal upwards.
3. Remove the box spanner from the vehicle tools.
4. Fit the box spanner on the bolt, to the maximum, and hold in this
position. At the same time press the safety ring downwards
Ÿ.
5. Turn the box spanner several times to the left, until the spare
wheel can be fitted, hanging from a wire, vertically behind the
vehicle.
6. Separate the plastic pieces so that they may be inserted into the
central aperture of the rim and so free the wheel.
A6
A7
Fig. 153 Taking out the
spare wheel
AA
AB
AC
AD
AC
Page 235 of 299

If and when233
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a
WARNING
•If you are driving without the spare wheel, the cable should be rolled up
and the bracket fastened to the floor of the luggage compartment.
Fitting the defective wheel in the spare wheel casing
1. Place the wheel behind the vehicle.
2. Insert the support on the inside of the defective wheel, through
a central opening.
3. Insert the defective wheel below the vehicle, with the outer side
facing downwards.4. Remove the wheel spanner Ÿpage 232, fig. 153 and turn
the bolt on the floor of the luggage compartment several times to
the right, until the defective wheel is firmly secured against the
inside of the luggage compartment floor Ÿ in “Taking out
the spare wheel” on page 232.
5. Close the opening with the rubber seal Ÿpage 232, fig. 153
and lower the cover .
WARNING
Tighten the bolt of the luggage compartment to a maximum torque of 25
Nm.
Fig. 154 Resting point for
the spare wheel on the
bumper
AC
AB
AA
Page 236 of 299

If and when 234
Breakdown set*
Components
Components
The anti-puncture kit contains the following components:
Tyre valve remover
Sticker indicating maximum speed “max. 80 km/h” or “max. 50mph”
Filler tube with cap
Compressor
Tube for inflating tyres
Pressure gauge
Air bleed screw
ON/OFF switch
12 volt connector
Bottle of sealant Ÿ
Spare tyre valve
Caution
•Note the expiry date on the bottle of tyre sealant Do not use sealant paste
that has expired. A bottle of tyre sealant can be obtained at any SEAT dealer.
•Dispose of used or expired sealant observing any legal requirements.
•Likewise, note any instructions from the anti-puncture kit's manufacturer
(if included).
Note
•In vehicles fitted with a towing bracket, it is first necessary to remove the
tools in order to reach the anti-puncture kit.
Preparation of anti-puncture kit
Small punctures (up to 4 mm in diameter), particularly ones
in the tread, can be sealed using the anti-puncture set.
If you have a puncture, stop the car well away from moving traffic.
Switch on the hazard warning lights and set the emergency triangle
in position. Please observe legal requirements when doing so.
– Take the compressor and the bottle of sealant from the luggage
compartment.
– Take the sticker Ÿfig. 155 out of the anti-puncture set and
apply it to the dash panel where it can be seen clearly.
– Leave the foreign body (e. g. screw, nail) in the tyre.
– Take the cap off the tyre valve.
Fig. 155 Contents of anti-
puncture kit
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A2
Page 237 of 299