2006 NISSAN VERSA brake

TROUBLE DIAGNOSIS
AT-65
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
4. CHECK SHIFT-UP (D3 TO D4 ) AND ENGINE BRAKE
Release accelerator pedal after shifting from D
2 to D3 .
Read gear position, throttle opening and vehicle speed.
Refer to AT-8 4, "
DATA MONITOR MODE" .
Does A/T shift from D
3 to D4 and does vehicle decelerate by engine
brake?
YES >> 1. Stop vehicle.
2. Go to AT- 6 5 , "
Cruise Test — Part 3" .
NO >>

Mark the box on the AT-47, "DIAGNOSTIC WORK-
SHEET" .

Go to AT-212, "A/T Does Not Shift: D3 → D4" .

Continue “Road Test”.
Cruise Test — Part 3UCS005MW
1. CHECK SHIFT-DOWN (D4 TO D3 )
1. Push overdrive control switch. (OD OFF indicator lamp is off.)
2. Move selector lever to “D” position.
3. Accelerate vehicle using half throttle to D
4 .
4. Release accelerator pedal.
5. Push overdrive control switch. (OD OFF indicator lamp is on.)
Read gear position and vehicle speed. Refer to AT- 8 4 ,
"DATA MONITOR MODE" .
Does A/T shift from D
4 to D3 (OD OFF)?
YES >> GO TO 2.
NO >>

Mark the box on the AT-47, "DIAGNOSTIC WORK-
SHEET" .

Go to AT-218, "A/T Does Not Shift: D4 → D3 , When
OD OFF" .

Continue “Road Test”.
SAT4 0 5H
SAT8 1 2A
SAT8 1 3A
SCIA5469E

AT-66
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
2. CHECK ENGINE BRAKE
Check engine brake.
Does vehicle decelerate by engine brake?
YES >> GO TO 3.
NO >>

Mark the box on the AT - 4 7 , "DIAGNOSTIC WORK-
SHEET" .

Go to AT-223, "Vehicle Does Not Decelerate by
Engine Brake" .

Continue “Road Test”.
3. CHECK SHIFT-DOWN (D3 TO 22 )
Move selector lever from “D” to “2” position while driving in D
3 (OD
OFF).
Read gear position. Refer to AT-84, "
DATA MONITOR MODE"
.
Does A/T shift from D
3 (OD OFF) to 22 ?
YES >> GO TO 4.
NO >>

Mark the box on the AT - 4 7 , "DIAGNOSTIC WORK-
SHEET" .

Go to AT-219, "A/T Does Not Shift: D3 → 22 , When
Selector Lever “D” → “2” Position" .

Continue “Road Test”.
4. CHECK ENGINE BRAKE
Check engine brake.
Does vehicle decelerate by engine brake?
YES >> GO TO 5.
NO >>

Mark the box on the AT - 4 7 , "DIAGNOSTIC WORK-
SHEET" .

Go to AT-223, "Vehicle Does Not Decelerate by
Engine Brake" .

Continue “Road Test”.
5. CHECK SHIFT-DOWN (22 TO 11 )
Move selector lever from “2” to “1” position while driving in 2
2 .
Read gear position. Refer to AT-84, "
DATA MONITOR MODE"
.
Does A/T shift from 2
2 to 11 position?
YES >> GO TO 6.
NO >>

Mark the box on the AT - 4 7 , "DIAGNOSTIC WORK-
SHEET" .

Go to AT- 2 2 1 , "A/T Does Not Shift: 22 → 11 , When
Selector Lever “2” → “1” Position" .

Continue “Road Test”.
SCIA5469E
SAT7 9 1GA
SAT7 9 1GA
SAT7 7 8B

TROUBLE DIAGNOSIS
AT-67
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
6. CHECK ENGINE BRAKE
Check engine brake.
Does vehicle decelerate by engine brake?
YES >> 1. Stop vehicle.
2. Perform self-diagnosis. Refer to AT-82, "
SELF-DIAG-
NOSTIC RESULT MODE" , AT-90, "Diagnostic Proce-
dure Without CONSULT-II" .
NO >>

Mark the box on the AT-47, "DIAGNOSTIC WORK-
SHEET" .

Go to AT-223, "Vehicle Does Not Decelerate by
Engine Brake" .

Stop “Road Test”.
Vehicle Speed at Which Gear Shifting OccursUCS005M X

At half throttle, the accelerator opening is 4/8 of the full opening.
Vehicle Speed at Which Lock-up Occurs/ReleasesUCS005M Y
SAT7 7 8B
Throttle positionVehicle speed km/h (MPH)
D1 → D2D2 → D3D3 → D4D4 → D3D3 → D2D2 → D1
Full throttle51 - 59
(32 - 37)97 - 105
(60 - 65)154 - 162
(96 - 101)150 - 158
(93 - 98)87 - 95
(54 - 59)40 - 48
(25 - 30)
Half throttle34 - 42
(21 - 26)62 - 70
(39 - 43)124 - 132
(77 - 82)69 - 77
(43 - 48)36 - 44
(22 - 27)19 - 27
(12 - 17)
Throttle position Selector lever positionVehicle speed km/h (MPH)
Lock-up ON Lock-up OFF
2.0/8“D” position 86 - 94 (53 - 58) 59 - 67 (37 - 42)
“D” position (OD OFF) 86 - 94 (53 - 58) 83 - 91 (52 - 57)

AT-68
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
Symptom ChartUCS005M Z
Numbers are arranged in order of inspection.
Perform inspections starting with number one and work up.
Items Symptom Condition Diagnostic item Reference page
No Lock-up Engage-
ment/TCC Inopera-
tiveTorque converter is
not locked up.ON vehicle1. Accelerator pedal position sensorEC-532
2. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7, AT- 1 6 6
3. Engine speed signalAT- 11 3
4. A/T fluid temperature sensorAT- 1 0 2
5. Line pressure testAT- 5 6
6. Torque converter clutch solenoid valveAT- 1 3 4
7. Control valve assemblyAT- 2 4 2
OFF vehicle 8. Torque converterAT- 2 6 8
Torque converter
clutch piston slip.ON vehicle1. A/T fluid levelAT- 1 6
2. Accelerator pedal position sensorEC-532
3. Line pressure testAT- 5 6
4. Torque converter clutch solenoid valveAT- 1 3 4
5. Line pressure solenoid valveAT- 1 4 5
6. Control valve assemblyAT- 2 4 2
OFF vehicle 7. Torque converterAT- 2 6 8
Lock-up point is
extremely high or low.ON vehicle1. Accelerator pedal position sensorEC-5322. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7, AT- 1 6 6
3. Torque converter clutch solenoid valveAT- 1 3 4
4. Control valve assemblyAT- 2 4 2
Shift ShockSharp shock in shift-
ing from “N” to “D”
position.ON vehicle1. Engine idling speedEC-75
2. Accelerator pedal position sensorEC-532
3. Line pressure testAT- 5 6
4. A/T fluid temperature sensorAT- 1 0 2
5. Engine speed signalAT- 11 3
6. Line pressure solenoid valveAT- 1 4 5
7. Control valve assemblyAT- 2 4 2
8. Accumulator N-DAT- 2 4 2
OFF vehicle 9. Forward clutchAT- 3 2 0
Too sharp a shock in
changing from D
1 to
D
2 .ON vehicle1. Accelerator pedal position sensorEC-532
2. Line pressure testAT- 5 6
3. Accumulator servo releaseAT- 2 4 2
4. Control valve assemblyAT- 2 4 2
5. A/T fluid temperature sensorAT- 1 0 2
OFF vehicle 6. Brake bandAT- 3 4 3

TROUBLE DIAGNOSIS
AT-69
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
Shift ShockToo sharp a shock in
changing from D
2 to
D
3 .ON vehicle1. Accelerator pedal position sensorEC-532
2. Line pressure testAT- 5 6
3. Control valve assemblyAT- 2 4 2
OFF vehicle4. High clutchAT- 3 1 45. Brake bandAT- 3 4 3
Too sharp a shock in
changing from D
3 to
D
4 .ON vehicle1. Accelerator pedal position sensorEC-532
2. Line pressure testAT- 5 6
3. Control valve assemblyAT- 2 4 2
OFF vehicle4. Brake bandAT- 3 4 35. Overrun clutchAT- 3 2 0
6. Forward one-way clutchAT- 3 3 2
Gear change shock
during deceleration
by releasing accelera-
tor pedal.ON vehicle1. Accelerator pedal position sensorEC-5322. Line pressure testAT- 5 6
3. Overrun clutch solenoid valveAT- 1 6 1
4. Control valve assemblyAT- 2 4 2
Large shock in
changing from 1
2 to
1
1 in “1” position.ON vehicle 1. Control valve assemblyAT- 2 4 2OFF vehicle 2. Low & reverse brakeAT- 3 2 7
Improper Shift TimingToo high a gear
change point from D
1
to D
2 , from D2 t o D3 ,
from D
3 to D4 .ON vehicle1. Accelerator pedal position sensorEC-532
2. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7, AT- 1 6 6
3. Shift solenoid valve AAT- 1 5 1
4. Shift solenoid valve BAT- 1 5 6
Gear change directly
from D
1 to D3
occurs.ON vehicle1. A/T fluid levelAT- 1 62. Accumulator servo releaseAT- 2 4 2
OFF vehicle 3. Brake bandAT- 3 4 3
Too high a change
point from D
4 to D3 ,
from D
3 to D 2 , from
D
2 to D1 .ON vehicle1. Accelerator pedal position sensorEC-532
2. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7, AT- 1 6 6
Kickdown does not
operate when
depressing accelera-
tor pedal in D
4 within
kickdown vehicle
speed.ON vehicle1. Accelerator pedal position sensorEC-532
2. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7, AT- 1 6 6
3. Shift solenoid valve AAT- 1 5 1
4. Shift solenoid valve BAT- 1 5 6
Kickdown operates or
engine overruns
when depressing
accelerator pedal in
D
4 beyond kickdown
vehicle speed limit.ON vehicle1. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7
, AT- 1 6 6
2. Accelerator pedal position sensorEC-532
3. Shift solenoid valve AAT- 1 5 1
4. Shift solenoid valve BAT- 1 5 6
Gear change from 22
to 2
3 in “2” position.ON vehicle1. PNP switch adjustmentAT- 2 4 72. Control cable adjustmentAT- 2 3 3
Gear change from 11
to 1
2 in “1” position.ON vehicle1. PNP switch adjustmentAT- 2 4 72. Control cable adjustmentAT- 2 3 3
Items Symptom Condition Diagnostic item Reference page

AT-70
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
No Down ShiftFailure to change
gear from D
4 to D3 .ON vehicle1. A/T fluid levelAT- 1 6
2. Accelerator pedal position sensorEC-532
3. Overrun clutch solenoid valveAT- 1 6 1
4. Shift solenoid valve A AT- 1 5 1
5. Line pressure solenoid valveAT- 1 4 5
6. Control valve assemblyAT- 2 4 2
OFF vehicle7. Brake bandAT- 3 4 38. Overrun clutchAT- 3 2 0
Failure to change
gear from D
3 to D2
or from D
4 to D2 .ON vehicle1. A/T fluid levelAT- 1 6
2. Accelerator pedal position sensorEC-532
3. Shift solenoid valve AAT- 1 5 1
4. Shift solenoid valve BAT- 1 5 6
5. Control valve assemblyAT- 2 4 2
OFF vehicle6. High clutchAT- 3 1 47. Brake bandAT- 3 4 3
Failure to change
gear from D
2 to D1
or from D
3 to D1 .ON vehicle1. A/T fluid levelAT- 1 6
2. Accelerator pedal position sensorEC-532
3. Shift solenoid valve AAT- 1 5 1
4. Shift solenoid valve BAT- 1 5 6
5. Control valve assemblyAT- 2 4 2
OFF vehicle6. Low one-way clutchAT- 2 6 87. High clutchAT- 3 1 4
8. Brake bandAT- 3 4 3
Failure to change
from D
3 to 22 when
shifting selector lever
into “2” position.
AT- 2 1 9ON vehicle1. Accelerator pedal position sensorEC-5322. Shift solenoid valve BAT- 1 5 6
3. Control valve assembly AT- 2 4 2
4. Control cable adjustmentAT- 2 3 3
OFF vehicle 5. Brake bandAT- 3 4 3
Does not change
from 1
2 to 11 in 1st
position.ON vehicle1. PNP switch adjustmentAT- 2 4 7
2. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7, AT- 1 6 6
3. Shift solenoid valve AAT- 1 5 1
4. Control valve assemblyAT- 2 4 2
5. Overrun clutch solenoid valveAT- 1 6 1
OFF vehicle6. Overrun clutchAT- 3 2 07. Low & reverse brakeAT- 3 2 7
Items Symptom Condition Diagnostic item Reference page

TROUBLE DIAGNOSIS
AT-71
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
No Up ShiftFailure to change
gear from D
1 to D2 .ON vehicle1. Control cable adjustmentAT- 2 3 3
2. Shift solenoid valve AAT- 1 5 1
3. Control valve assemblyAT- 2 4 2
4. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7, AT- 1 6 6
5. Accelerator pedal position sensorEC-532
OFF vehicle 6. Brake bandAT- 3 4 3
Failure to change
gear from D
2 to D3 .ON vehicle1. Control cable adjustmentAT- 2 3 3
2. Shift solenoid valve BAT- 1 5 6
3. Control valve assemblyAT- 2 4 2
4. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7, AT- 1 6 6
5. Accelerator pedal position sensorEC-532
OFF vehicle6. High clutchAT- 3 1 47. Brake bandAT- 3 4 3
Failure to change
gear from D
3 to D4 .ON vehicle 1. PNP switch adjustmentAT- 2 4 7
2. Overdrive control switchAT- 1 8 6
3. Control cable adjustmentAT- 2 3 3
4. Shift solenoid valve AAT- 1 5 1
5. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7, AT- 1 6 6
6. A/T fluid temperature sensorAT- 1 0 2
OFF vehicle 7. Brake band AT- 3 4 3
A/T does not shift to
D
4 when driving with
OD ON. (OD OFF
indicator lamp is off.)ON vehicle1. Accelerator pedal position sensorEC-532
2. PNP switch adjustmentAT- 2 4 7
3. Overdrive control switchAT- 1 8 6
4. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRAT- 1 0 7, AT- 1 6 6
5. Shift solenoid valve AAT- 1 5 1
6. Overrun clutch solenoid valveAT- 1 6 1
7. Control valve assemblyAT- 2 4 2
8. A/T fluid temperature sensorAT- 1 0 2
9. Line pressure solenoid valveAT- 1 4 5
OFF vehicle10. Brake bandAT- 3 4 311. Overrun clutchAT- 3 2 0
Items Symptom Condition Diagnostic item Reference page

AT-72
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
Slips/Will Not EngageVehicle will not run in
“R” position (but runs
in “D”, “2” and “1”
positions). Clutch
slips.
Very poor accelera-
tion.ON vehicle1. Control cable adjustmentAT- 2 3 3
2. Stall testAT- 5 3
3. Line pressure testAT- 5 6
4. Line pressure solenoid valveAT- 1 4 5
5. Control valve assemblyAT- 2 4 2
OFF vehicle6. Reverse clutchAT- 3 0 9
7. High clutchAT- 3 1 4
8. Forward clutchAT- 3 2 0
9. Overrun clutchAT- 3 2 0
10. Low & reverse brakeAT- 3 2 7
Vehicle will not run in
“D” and “2” positions
(but runs in “1” and
“R” positions).ON vehicle 1. Control cable adjustmentAT- 2 3 3
OFF vehicle 2. Low one-way clutchAT- 2 6 8
Vehicle will not run in
“D”, “1”, “2” positions
(but runs in R posi-
tion). Clutch slips.
Very poor accelera-
tion.ON vehicle1. A/T fluid levelAT- 1 6
2. Stall testAT- 5 3
3. Line pressure testAT- 5 6
4. Line pressure solenoid valveAT- 1 4 5
5. Control valve assemblyAT- 2 4 2
6. Accumulator N-DAT- 2 4 2
OFF vehicle7. Reverse clutchAT- 3 0 9
8. High clutchAT- 3 1 4
9. Forward clutchAT- 3 2 0
10. Forward one-way clutchAT- 3 3 2
11. Low one-way clutchAT- 2 6 8
Clutches or brakes
slip somewhat in
starting.ON vehicle1. A/T fluid levelAT- 1 6
2. Control cable adjustmentAT- 2 3 3
3. Accelerator pedal position sensorEC-532
4. Line pressure testAT- 5 6
5. Line pressure solenoid valveAT- 1 4 5
6. Control valve assemblyAT- 2 4 2
7. Accumulator N-DAT- 2 4 2
OFF vehicle8. Forward clutchAT- 3 2 0
9. Reverse clutchAT- 3 0 9
10. Low & reverse brakeAT- 3 2 7
11 . O il p u m pAT- 2 8 9
12. Torque converterAT- 2 6 8
Items Symptom Condition Diagnostic item Reference page