2006 NISSAN VERSA rear view mirror

WHEEL SENSORS
BRC-33
[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: June 20062007 Versa
WHEEL SENSORSPFP:47910
Removal and InstallationEFS006L4
NOTE:
The top portion of the figure (front side) shows view from LH side of vehicle. RH side is the mirror image.
REMOVAL
Pay attention to the following when removing wheel sensor.
CAUTION:

As much as possible, avoid rotating wheel sensor when removing it. Pull wheel sensors out with-
out pulling on sensor harness.

Take care to avoid damaging wheel sensor edges or rotor teeth. Remove wheel sensor first before
removing front or rear wheel hub. This is to avoid damage to wheel sensor wiring and loss of sen-
sor function.
INSTALLATION
Pay attention to the following when installing wheel sensor. Tighten installation bolts and nuts to the specified
torques.

When installing, make sure there is no foreign material such as iron chips on and in the mounting hole of
the wheel sensor. Make sure no foreign material has been caught in the sensor rotor. Remove any foreign
material and clean the mount.

When installing front wheel sensor, press rubber grommets of strut bracket and body all the way in until
they get locked, and be careful not to apply a twist to harness. Harness should not be twisted after instal-
lation. (Install it with harness paint mark on body side grommet facing front of vehicle, and the strut side
grommet facing outside of vehicle.)
A. Front B. Rear 1. Front wheel sensor connector (LH)
2. Front wheel sensor (LH) 3. Rear wheel sensor (LH) 4. Rear wheel sensor connector (LH)
5. Rear wheel sensor connector (RH) 6. Rear wheel sensor (RH) 7. Side member
8. Left 9. Right : Front
Refer to GI section for symbol marks in the figure.
SFIA3090E

GI-46
RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS
Revision: June 20062007 Versa
RECOMMENDED CHEMICAL PRODUCTS AND SEALANTSPFP:00000
Recommended Chemical Products and SealantsEAS0021Q
Refer to the following chart for help in selecting the appropriate chemical product or sealant.
Product Description PurposeNissan North America
Part No. (USA)Nissan Canada Part
No. (Canada)Aftermarket Cross-
reference Part Nos.
1Rear View Mirror
AdhesiveUsed to permanently
remount rear view mirrors
to windows.999MP-AM000P 99998-50505 Permatex 81844
2Anaerobic Liquid Gas-
ketFor metal-to-metal flange
sealing.
Can fill a 0.38 mm (0.015
inch) gap and provide
instant sealing for most
powertrain applications.999MP-AM001P 99998-50503Permatex 51813 and
51817
3High Performance
Thread SealantProvides instant sealing on
any threaded straight or
parallel threaded fitting.
(Thread sealant only, no
locking ability.)

Do not use on plastic.999MP-AM002P 999MP-AM002P Permatex 56521
4 Silicone RTVGasket Maker999MP-AM003P
(Ultra Grey)99998-50506
(Ultra Grey)Permatex Ultra Grey
82194;
Three Bond
1207,1215, 1216,
1217F and 1217G;
Nissan RTV Part No.
999MP-A7007
Gasket Maker for Maxima/
Quest 5-speed automatic
transmission
(RE5F22A)––Three Bond 1281B
or exact equivalent
in its quality
5High Temperature,
High Strength Thread
Locking Sealant (Red)Threadlocker 999MP-AM004P 999MP-AM004PPermatex 27200;
Three Bond 1360,
1360N, 1305 N&P,
1307N, 1335,
1335B, 1363B,
1377C, 1386B, D&E
and 1388
6Medium Strength
Thread Locking Seal-
ant (Blue)Threadlocker (service tool
removable)999MP-AM005P 999MP-AM005PPermatex 24200,
24206, 24240,
24283 and 09178;
Three Bond 1322,
1322N, 1324 D&N,
1333D, 1361C,
1364D, 1370C and
1374

GW-1
GLASSES, WINDOW SYSTEM & MIRRORS
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION GW
A
B
GW
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Procedures without Cowl Top Cover ..... 3
Handling for Adhesive and Primer ........................... 3
PREPARATION ........................................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
OVERHEAD CONSOLE (FRONT AND REAR) ..... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
WINDSHIELD GLASS ...............................................11
Removal and Installation .........................................11
REMOVAL ............................................................11
INSTALLATION ................................................... 12
OPERA WINDOW GLASS ....................................... 13
Removal and Installation ........................................ 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 13
REAR WINDOW GLASS AND MOLDING ............... 15
Removal and Installation ........................................ 15
REMOVAL ........................................................... 15
INSTALLATION ................................................... 16
POWER WINDOW SYSTEM .................................... 17Component Parts and Harness Connector Location ... 17
System Description ................................................. 17
MANUAL OPERATION ........................................ 18
AUTO OPERATION ............................................. 20
POWER WINDOW LOCK ................................... 21
RETAINED POWER OPERATION ...................... 21
CAN Communication System Description .............. 21
Schematic ............................................................... 22
Wiring Diagram — WINDOW — ............................. 23
Main Power Window and Door Lock/Unlock Switch
Harness Connector Terminal Layout ...................... 27
Terminal and Reference Value for Main Power Win-
dow and Door Lock/Unlock Switch ......................... 27
Terminal and Reference Value for BCM ................. 28
Work Flow ............................................................... 28
CONSULT-II Function (BCM) ................................. 28
CONSULT-II START PROCEDURE .................... 28
ACTIVE TEST ..................................................... 29
WORK SUPPORT ............................................... 29
DATA MONITOR ................................................. 29
Trouble Diagnoses Symptom Chart ....................... 29
BCM Power Supply and Ground Circuit Check ...... 30
Main Power Window and Door Lock/Unlock Switch
Power Supply and Ground Circuit Check ............... 30
Front Power Window Motor LH Circuit Check ........ 32
Front Power Window RH Circuit Check (Power Win-
dow and Door Lock/Unlock Switch RH Operation) ... 33
Front Power Window Motor RH Circuit Check ....... 33
Encoder Circuit Check ............................................ 34
Door Switch Check ................................................. 37
Rear Power Window LH Circuit Check (Rear Power
Window Switch LH Operation) ................................ 38
Rear Power Window RH Circuit Check (Rear Power
Window Switch RH Operation) ............................... 39
Rear Power Window Motor LH Circuit Check ......... 39
Rear Power Window Motor RH Circuit Check ........ 41
FRONT DOOR GLASS AND REGULATOR ............. 43
Removal and Installation ........................................ 43
DOOR GLASS ..................................................... 43
REGULATOR ASSEMBLY .................................. 44

GW-50
REAR WINDOW DEFOGGER
Revision: June 20062007 Versa
REAR WINDOW DEFOGGERPFP:25350
Component Parts and Harness Connector LocationEIS009CK
System DescriptionEIS0 09 CL
The rear window defogger system is controlled by BCM (body control module) and IPDM E/R (intelligent
power distribution module engine room).
The rear window defogger only operates for approximately 15 minutes.
Power is supplied at all times

through 15A fuses (No. 46 and 47, located in the IPDM E/R)

to rear window defogger relay

through 10A fuse [No. 5 (with heated mirrors), located in the fuse block (J/B)]

to heated mirror relay terminal 3

through 40A fusible link (letter g , located in the fuse and fusible link box)

to BCM terminal 70.
With the ignition switch turned to ON or START position, power is supplied

through ignition relay

to rear window defogger relay (located in the IPDM E/R)

through 10A fuse [No. 6, located in the fuse block (J/B)]

to BCM terminal 38.
Ground is supplied

to BCM terminal 67 and
1. BCM M18, M20 (view with glove box
removed)2. Front air control M33 3. A. Rear window defogger ground
connector D413
B. Rear window defogger connector
D412
C. Condenser D409, D411
4. IPDM E/R E46, E48 5. Door mirror LH D4, RH D107 (with
heated mirrors)6. Heated mirror relay M48 (with
heated mirrors)
LIIA2642E

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Collision diagnosis .......................................... SRS-54
Combination lamp, rear, removal and installation LT-87
Combination meter ................................................ DI-5
Combination meter removal and installation - See Instru-
ment panel .......................................................... IP-11
COMBSW - Wiring diagram ............................... LT-67
Component Location (manual A/C) ................ MTC-25
Compression pressure ...................................... EM-62
Compressor mounting .................................... MTC-84
Compressor special service tool .................... MTC-12
Condenser ...................................................... MTC-88
Connecting rod .................................................. EM-97
Connecting rod bearing clearance .................. EM-101
Connecting rod bushing clearance .................... EM-97
CONSULT for ABS .......................................... BRC-20
CONSULT general information .......................... GI-37
CONSULT-II for engine ................................... EC-113
CONSULT-II function (EPS) ............................ STC-13
CONSULT-II Reference value (CVT) .............. CVT-57
Control lever (M/T) ............................................ MT-12
Control units (terminal arrangement) ................ PG-72
Control valve (CVT) ......................................... CVT-29
Converter housing installation ............ AT-254, AT-369
COOL/F - Wiring diagram ............................... EC-448
Coolant mixture ratio ......................................... MA-12
Cooling circuit (engine) ....................................... CO-7
Cooling fan ........................................................ CO-15
Cooling fan motor ............................................ EC-443
Corrosion protection ......................................... BL-237
Coupling sleeve (M/T) ....................................... MT-18
Crankcase ventilation system - See Positive crankcase
ventilation .......................................................... EC-44
Crankshaft ......................................................... EM-77
Crankshaft position sensor (POS) ................... EC-319
Crash zone sensor .......................................... SRS-49
CVT air breather hose ................................... CVT-205
CVT control system ......................................... CVT-22
CVT cross-sectional view ................................ CVT-21
CVT Electrical parts location ........................... CVT-40
CVT fluid checking ............... CVT-16, CVT-43, MA-20
CVT fluid cooler cleaning ................................ CVT-18
CVT fluid replacement ........................ CVT-17, MA-21
CVT fluid temparature sensor ......................... CVT-85
CVT hydraulic control system ......................... CVT-23
CVT indicator ...................................................... DI-42
CVT self-diagnoses ........................... CVT-60, CVT-67
CVT shift lock system .................................... CVT-197
CVT trouble diagnoses .................................... CVT-34
CVTIND - Wiring diagram ................................... DI-43
Cylinder block .................................................... EM-77
Cylinder head .................................................... EM-62
Cylinder head bolt tightening ............................. EM-65
D
D/LOCK - Wiring diagram ...................... BL-26
, BL-31
Data link connector ............. EC-115, EC-127, EC-592
DEF - Wiring diagram ....................................... GW-52
Diagnosis sensor unit ...................................... SRS-52
Diagnostic trouble code (DTC) for OBD system . EC-8,
EC-48
Diagnostic trouble code (DTC) inspection priority chart
EC-89
, CVT-34
Differential gear (FF M/T) .................................. MT-22
Differentil side oil seal .................................... CVT-206
DLC - Wiring diagram ...................................... EC-592
Door glass .......................................... GW-43, GW-47
Door glass Fitting Adjustment(Front) ................ GW-46
Door glass Fitting Adjustment(Rear) ................ GW-49
Door mirror ....................................................... GW-65
Door trim .............................................................. EI-27
Door, front ......................................................... GW-43
Door, rear ......................................................... GW-47
Drive shaft ......................................................... MA-27
Driver air bag ................................................... SRS-41
Dropping resistor (A/T) .................................... AT-150
DTC work support ............................................ EC-122
DTRL - Wiring diagram ....................................... LT-31
Duct and grilles ............................................... MTC-75
E
ECM input/output signal .................................. EC-105
ECM power supply .......................................... EC-144
ECTS - Wiring diagram .................................... EC-202
Electric sunroof .................................................. RF-10
Electric throttle control actuator .. EM-18, EC-499, EC-
506, EC-511
Electrical load signal circuit ............................. EC-562
Electrical unit ..................................................... PG-72
Electrical units location ...................................... PG-64
Electronic ignition (EI) system ........................... EC-25
Electronic key ..................................................... BL-80
ENG SS - Wiring diagram ................................ AT-114
Engine control circuit diagram ......................... EC-103
Engine control component parts location .......... EC-96
Engine control module (ECM) ......................... EC-427
Engine control system diagram ......................... EC-22
Engine coolant ..................................................... CO-8
Engine coolant temperature sensor (ECTS) ... EC-200,
EC-212
Engine fail-safe system ..................................... EC-91
Engine oil ............................................................. LU-5
Engine oil precautions .......................................... GI-7
Engine removal .................................................. EM-73
EPS - Wiring diagram ........................................ STC-9
EPS control unit input/output signal reference values ..
STC-11
EPS system description ..................................... STC-5
EPS system diagram ......................................... STC-6
ETC1 - Wiring diagram .................................... EC-500
ETC2 - Wiring diagram .................................... EC-495
ETC3 - Wiring diagram .................................... EC-507
EVAP canister ................................................... EC-34
EVAP canister purge volume control solenoid valve ....
EC-354
, EC-362
EVAP canister vent control valve ...... EC-369, EC-376
EVAP control system (small leak) diagnosis .. EC-346,