2006 NISSAN VERSA bulb

LT-60
TURN SIGNAL AND HAZARD WARNING LAMPS
Revision: June 20062007 Versa
2. CHECK FRONT TURN SIGNAL LAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and front combination lamp LH or
RH connector.
3. Check continuity between BCM harness connector M20 (A) ter-
minal 60 and front combination lamp LH harness connector E29
(B) terminal 4.
4. Check continuity between BCM harness connector M20 terminal
61 (A) and front combination lamp RH harness connector E30
(B) terminal 4.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK GROUND CIRCUIT
1. Check continuity between front combination lamp LH harness
connector E29 terminal 5 and ground.
2. Check continuity between front combination lamp RH harness
connector E30 terminal 5 and ground.
OK or NG
OK >> Inspect connection at front combination lamp.
NG >> Repair harness.
Rear Turn Signal Lamp Does Not OperateEKS00IXC
1. CHECK BULB
Verify the bulb standard of each turn signal lamp is correct. Refer to LT- 11 6 , "
Exterior Lamp" .
OK or NG
OK >> GO TO 2.
NG >> Replace turn signal lamp bulb. Refer to LT- 6 4 , "
Bulb Replacement of Rear Turn Signal Lamp" . 60 - 4 : Continuity should exist.
61 - 4 : Continuity should exist.
WKIA5612E
5 - Ground : Continuity should exist.
5 - Ground : Continuity should exist.
WKIA5613E

LT-64
TURN SIGNAL AND HAZARD WARNING LAMPS
Revision: June 20062007 Versa
Bulb Replacement of Front Turn Signal LampEKS00HYB
Refer to LT- 2 5 , "Bulb Replacement" .
Bulb Replacement of Rear Turn Signal LampEKS00HYC
Refer to LT- 8 7 , "Bulb Replacement" .
Removal and Installation of Front Turn Signal LampEKS00HYE
Refer to LT- 2 5 , "Removal and Installation" .
Removal and Installation of Rear Turn Signal Lamp EKS00HYF
Refer to LT- 8 7 , "Removal and Installation" .

LT-72
STOP LAMP
Revision: June 20062007 Versa
Bulb Replacement of High-Mounted Stop LampEKS00HYR
Refer to LT- 7 2 , "Removal and Installation of High-Mounted Stop Lamp" .
Bulb Replacement of Rear Combination Lamp for Stop LampEKS00HYS
Refer to LT- 8 7 , "Bulb Replacement" .
Removal and Installation of High-Mounted Stop LampEKS00HYT
REMOVAL
1. Remove rear hatch finish panel. Refer to EI-42, "LUGGAGE FLOOR TRIM" .
2. Disconnect the high-mounted stop lamp connector.
3. Remove nuts and remove high-mounted stop lamp from rear hatch.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Properly seal the high-mounted stop lamp base to the rear hatch to prevent water leaks.
Removal and Installation of Rear Combination Lamp for Stop LampEKS00HYU
Refer to LT- 8 7 , "Removal and Installation" .

LT-74
BACK-UP LAMP
Revision: June 20062007 Versa
Bulb ReplacementEKS00HYW
Refer to LT- 8 7 , "Bulb Replacement" .
Removal and InstallationEKS00HYX
Refer to LT- 8 7 , "Removal and Installation" .

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-85
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
7. CHECK PARKING, LICENSE PLATE AND TAIL LAMPS GROUND CIRCUIT
1. Check continuity between front combination lamp harness con-
nector and ground.
2. Check continuity between license plate lamp harness connector
and ground.
3. Check continuity between rear combination lamp harness con-
nector and ground.
OK or NG
OK >> Check bulbs.
NG >> Repair harness or connector.
Parking, License Plate and Tail Lamps Do Not Turn OFF (After Approx. 10 Min-
utes)
EKS00HZB

This symptom is related to the ignition relay in IPDM E/R. Refer to PG-18, "Function of Detecting Ignition
Relay Malfunction" .

Select “BCM” on CONSULT-II. Select “HEADLAMP” on “SELECT TEST ITEM” screen and select “DATA
MONITOR” on “SELECT DIAG MODE” screen. If “LIGHT SW 1ST” is OFF when lighting switch is OFF,
replace IPDM E/R.
Front combination lamp connector Terminal
GroundContinuity
RH E54
7Yes
LH E53
WKIA5509E
License plate lamp
connectorTe r m i n a l
GroundContinuity
RH B17
2 Yes
LH B16
WKIA5510E
Rear combination lamp
connectorTe r m i n a l
GroundContinuity
RH B107
1Yes
LH B25
PKIC1029E

LT-86
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: June 20062007 Versa
Bulb ReplacementEKS00HZC
PA R K I N G L A M P
Refer to LT- 8 7 , "Bulb Replacement" .
LICENSE PLATE LAMP
1. Remove the license plate lamp. Refer to LT- 8 6 , "LICENSE PLATE LAMP" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb from the socket.
4. Installation is in the reverse order of removal.
TA I L L A M P
Refer to LT- 8 7 , "Bulb Replacement" .
Removal and InstallationEKS00HZD
PA R K I N G L A M P
Refer to LT- 8 7 , "Removal and Installation" .
LICENSE PLATE LAMP
Removal
1. Press the license plate lamp pawl on the side of the rear bumper fascia, then swing the license plate lamp
down to release the license plate lamp hook from the rear bumper fascia.
2. Disconnect the license plate lamp connector and remove the licence plate lamp.
Installation
Installation is in the reverse order of removal.
TA I L L A M P
Refer to LT- 8 7 , "Removal and Installation" .
1. License plate lamp A. Pawl B. Hook
LKIA0759E

REAR COMBINATION LAMP
LT-87
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
REAR COMBINATION LAMPPFP:26554
ComponentsEKS00IBB
Bulb ReplacementEKS00HZE
1. Remove the rear combination lamp. Refer to LT- 8 7 , "Removal and Installation" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
Removal and InstallationEKS00HZF
REMOVAL
1. Remove rear combination lamp nuts.
2. Pull the rear combination lamp toward rear of the vehicle and remove from the vehicle.
3. Disconnect rear combination lamp connector, and remove rear combination lamp.
INSTALLATION
Installation is in the reverse order of removal.
Disaassembly and AssemblyEKS00IBC
DISSASEMBLY
1. Remove the rear combination lamp harness.
2. Remove the bulbs from the rear combination lamp housing assembly.
3. Remove the bumper stay.
1. Rear combination lamp harness 2. Turn signal lamp bulb 3. Back-up lamp bulb
4. Stop/tail lamp bulb 5. Rear combination lamp housing
assembly6. Bumper stay
A. Grommet B. Nut C. Clip
D. Nuts E. Clip
LKIA0760E

INTERIOR LAMP
LT-89
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
INTERIOR LAMPPFP:28491
Map lampEKS00HZH
BULB REPLACEMENT
1. Remove the map lamp lens (1).
2. Remove the bulb from lamp.
NOTE:
Pull bulb end from Y-shaped connector first to remove.
3. Installation is in the reverse order of removal.

Install the map lamp lens (1) so the round lens is positioned to
the front of the vehicle as shown. There is a tab on the lens to
prevent incorrect installation of the lens.
REMOVAL AND INSTALLATION
Removal
1. Insert a suitable tool and disengage the pawl (A) fittings the map
lamp (1).
2. Disconnect map lamp connector and remove map lamp (1).
Installation
Installation is in the reverse order of removal.
DISASSEMBLY AND ASSEMBLY
Disassembly
1. Remove screw (A).
2. Remove sunroof switch (1).
Assembly
Assembly is in the reverse order of disassembly.
LKIA0773E
PKIC1038E
PKIC1039E