2006 INFINITI QX56 tf-105

TF-46
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
CAUTION:

If “CAN COMM CIRCUIT [U1000]” is displayed with other DTCs, first perform the trouble diagnosis for CAN communica-
tion line.

If “VHCL SPEED SEN·AT [P1808]”, “ABS OP SIG [P1830]”, “VDC OP SIG [P1831]” or “TCS OP SIG [P1832]” is displayed,
first perform the trouble diagnosis for ABS system.

If “VHCL SPEED SEN·AT [P1808]”, is displayed, first perform the trouble diagnosis for A/T system.
NOTE:

If "SHIFT ACT POSI SW [P1818]" or “SHIFT ACT CIR [P1819] ” is displayed, first erase self-diagnostic results. ("SHIFT ACT POSI
SW [P1818]" or “ SHIFT ACT CIR [P1819] ” may be displayed after installing transfer control unit or transfer assembly.)

If “CL PRES SW [P1827] ” or “ LINE PRES SW [P1828] ” is displayed only while driving in reverse, check the continuity of “R ” posi-
tion on A/T PNP switch. When there is nothing wrong with the electrical system, check the hydraulic system.
SHIFT ACT CIR
[P1819]

Transfer control device actuator circuit is shorted or open. (Mal-
functions are detected when transfer shift relay circuit is open/
shorted or relay monitor circuit is open/shorted.)

Malfunction occurs in transfer control device drive circuit.

Malfunction is detected in transfer shut off relay.
TF-81, "
Transfer Control Device"
Malfunction is detected in transfer shut off relay.
TF-54, "Power Supply Circuit For
Transfer Control Unit"
ENGINE SPEED SIG
[P1820]
Malfunction is detected in engine speed signal that is output from
ECM through CAN communication.

Improper signal is input while driving.TF-85, "
Engine Speed Signal
(ECM)"
DUTY SOLENOID
[P1822]
Proper voltage is not applied to clutch pressure solenoid valve
due to open or short circuit.
TF-86, "Clutch Pressure Sole-
noid"
2-4WD SOLENOID
[P1823]
Proper voltage is not applied to 2-4WD solenoid valve due to
open or short circuit.
TF-91, "2-4WD Solenoid"
MOTOR RELAY
[P1824]
Motor does not operate properly due to open or short circuit in
transfer motor or motor relay.TF-95, "Transfer Motor"
OIL TEMP SEN
[P1826]
Signal voltage from fluid temperature sensor is abnormally high
(Transfer fluid temperature is abnormally low) while driving.TF-102, "Transfer Fluid Temper-
ature"
CLUTCH PRES SW
[P1827]
Improper signal from clutch pressure switch is input due to open
or short circuit.

Malfunction occurs in clutch pressure switch or hydraulic circuit.TF-105, "
Clutch Pressure
Switch"
LINE PRES SW
[P1828]
Improper signal from line pressure switch is input due to open or
short circuit.

Malfunction occurs in line pressure switch or hydraulic circuit.
TF-108, "
Line Pressure Switch"
THROTTLE POSI SEN
[P1829]

Malfunction is detected in accelerator pedal position signal that is
output from ECM through CAN communication.

Signal voltage from accelerator pedal position sensor is abnor-
mally high or low.TF-111, "
Throttle Position Signal
(ECM)"
ABS OP SIG
[P1830]
Malfunction is detected in ABS operation signal that is output
from ABS actuator and electric unit (control unit) through CAN
communication.
TF-111, "ABS Operation Signal
(ABS)"
VDC OP SIG
[P1831]
Malfunction is detected in VDC operation signal that is output
from ABS actuator and electric unit (control unit) through CAN
communication.TF-112, "VDC Operation Signal
(ABS)"
TCS OP SIG
[P1832]
Malfunction is detected in TCS operation signal that is output
from ABS through CAN communication.
TF-112, "TCS Operation Signal
(ABS)"
CAN COMM CIRCUIT
[U1000]
Malfunction has been detected from CAN communication line.
TF-113, "CAN Communication
Line"
NO DTC IS DETECTED.
FURTHER TESTING MAY
BE REQUIRED.

No NG item has been detected.
—
Items (CONSULT-II screen
terms) Diagnostic item is detected when...
Check item

TF-52
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
9Transfer fluid tempera-
ture

Signal voltage from fluid temperature sensor is abnor-
mally high (Transfer fluid temperature is abnormally low)
while driving. TF-102, "Transfer Fluid
Temperature"
10
Neutral-4LO switch
Improper signal from neutral-4LO switch is input due to
open or short circuit. TF-59, "Neutral-4LO
Switch"
11
Clutch pressure switch

Improper signal from clutch pressure switch is input due
to open or short circuit.

Malfunction occurs in clutch pressure switch or hydraulic
circuit. TF-105, "
Clutch Pres-
sure Switch"
12
Line pressure switch

Improper signal from line pressure switch is input due to
open or short circuit.

Malfunction occurs in line pressure switch or hydraulic
circuit. TF-108, "
Line Pressure
Switch"
13
Engine speed signal
(from ECM)

Malfunction is detected in engine speed signal that is
output from ECM through CAN communication.

Improper signal is input while driving. TF-85, "
Engine Speed
Signal (ECM)"
14
Throttle position sen-
sor (from ECM)

Malfunction is detected in accelerator pedal position sig-
nal that is output from ECM through CAN communica-
tion.

Signal voltage from accelerator pedal position sensor is
abnormally high or low. TF-111, "
Throttle Posi-
tion Signal (ECM)"
15
Power supply
Power supply voltage for transfer control unit is abnor-
mally low while driving. TF-54, "Power Supply
Circuit For Transfer
Control Unit"
16
4WD shift switch
More than two switch inputs are simultaneously detected
due to short circuit of 4WD shift switch. TF-62, "4WD Shift
Switch"
17
ABS operation signal
(from ABS)

Malfunction is detected in ABS operation signal that is
output from ABS actuator and electric unit (control unit)
through CAN communication. TF-111, "ABS Operation
Signal (ABS)"
18
Wait detection switch
Improper signal from wait detection switch is input due to
open or short circuit. TF-66, "Wait Detection
Switch"
19
Actuator motor

Motor does not operate properly due to open or short cir-
cuit in actuator motor.

Malfunction is detected in the actuator motor. (When
4WD shift switch is operated and actuator motor is not
operated)

Malfunction is detected in transfer shift high relay and
transfer shift low relay. TF-70, "
Actuator
Motor", TF-54, "Power
Supply Circuit For
Transfer Control Unit"
20
Actuator position
switch

Improper signal from actuator position switch is input
due to open or short circuit.

Malfunction is detected in the actuator position switch. TF-77, "
Actuator Posi-
tion Switch"
21
Actuator circuit

Transfer control device actuator circuit is shorted or
open. (Malfunctions are detected when motor relay cir-
cuit is open/shorted or relay transfer shift circuit is open/
shorted.)

Malfunction occurs in transfer control device drive circuit. TF-81, "
Transfer Con-
trol Device"

Malfunction is detected in transfer shut off relay.
TF-54, "
Power Supply
Circuit For Transfer
Control Unit"
22
VDC operation signal
(from VDC)

Malfunction is detected in VDC operation signal that is
output from ABS actuator and electric unit (control unit)
through CAN communication. TF-112, "VDC Opera-
tion Signal (ABS)"
23
TCS operation signal
(from TCS)

Malfunction is detected in TCS operation signal that is
output from ABS actuator and electric unit (control unit)
through CAN communication. TF-112, "TCS Opera-
tion Signal (ABS)"
Flickering pattern or
flickering condition Items
Malfunction Check items

TROUBLE DIAGNOSIS FOR SYSTEMTF-105
CE F
G H
I
J
K L
M A
B
TF
Revision: November 2009 2006 QX56
Clutch Pressure SwitchEDS002IK
CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE
Data are reference value.
TRANSFER CONTROL UNIT TERMINALS AND REFERENCE VALUE
Data are reference value and are measured between each terminal and ground.
CAUTION:
When using a circuit tester to measure voltage for inspection, be sure not to extend forcibly any connector terminals.Monitored item [Unit]
Content ConditionDisplay value
CL PRES SW [ON /
OFF] Condition of clutch pres-
sure switch

Vehicle stopped

Engine running

A/T selector lever “
D” position

4WD shift switch: AUTO or 4H ( “Wait ” function is not
operating.) ON

Vehicle stopped

Engine running

4WD shift switch: 2WD (
“Wait ” function is not oper-
ating.) OFF
Terminal
Wire
color Item
ConditionData (Approx.)
34 BR Clutch pressure switch

Vehicle stopped

Engine running

A/T selector
lever “D ” position 4WD shift switch: AUTO or 4H (
“Wait ”
function is not operating.) 0V

Vehicle stopped

Engine running4WD shift switch: 2WD (
“Wait ” function is
not operating.) Battery voltage

TROUBLE DIAGNOSIS FOR SYMPTOMSTF-129
CE F
G H
I
J
K L
M A
B
TF
Revision: November 2009 2006 QX56
5. CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to TF-35, "
Transfer Control Unit Input/Output Signal Ref-
erence Values" .
OK or NG
OK >> Inspection End.
NG >> Check transfer control unit pin terminals for damage or loose connection with harness connector. If any items are damaged, repair or replace damaged parts.
4WD Warning Lamp Flashes SlowlyEDS002HS
SYMPTOM:
While driving, 4WD warning lamp flashes slowly. (When continuing to flash until turning ignition
switch OFF.)
NOTE:
Slow flashing: 1 time/2 seconds
DIAGNOSTIC PROCEDURE
1. CHECK TIRE
Check the following.

Tire pressure

Wear condition

Longitudinal tire size (There is no difference between longitudinal tires.)
OK or NG
OK >> GO TO 2.
NG >> Repair or replace damaged parts.
2. CHECK TRANSFER FLUID TEMPERATURE
Perform trouble diagnosis for transfer fluid temperature system. Refer to TF-102, "
Transfer Fluid Temperature"
.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. CHECK CLUTCH PRESSURE SWITCH
Perform trouble diagnosis for clutch pressure switch system. Refer to TF-105, "
Clutch Pressure Switch" .
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
4. SYMPTOM CHECK
Check again.
OK or NG
OK >> Inspection End.
NG >> GO TO 5.
5. CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to TF-35, "
Transfer Control Unit Input/Output Signal Ref-
erence Values" .
OK or NG
OK >> Inspection End.
NG >> Check transfer control unit pin terminals for damage or loose connection with harness connector. If any items are damaged, repair or replace damaged parts.

TF-130
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: November 20092006 QX56
Heavy Tight-corner Braking Symptom OccursEDS002HT
SYMPTOM:
Heavy tight-corner braking symptom occurs when vehicle is driven in AUTO mode and steering wheel
is turned fully to either side.
DIAGNOSTIC PROCEDURE
NOTE:

Light tight-corner braking symptom may occur depending on driving conditions in AUTO mode. This is not
a malfunction.

Heavy tight-corner braking symptom occurs when vehicle is driven in the following conditions: 4WD shift
switch is "4H" or "4LO", steering wheel is turned fully to either side.
1. CHECK SYSTEM FOR CAN COMMUNICATION LINE
Perform self-diagnosis. Refer to TF-50, "
SELF-DIAGNOSTIC PROCEDURE (WITH CONSULT-II)" .
Is "CAN COMM CIRCUIT [U1000]" displayed?
YES >> Perform trouble diagnosis for CAN communication line. Refer to TF-113, "CAN Communication
Line" .
NO >> GO TO 2.
2. CHECK SYSTEM FOR 4WD SHIFT SWITCH
Perform trouble diagnosis for 4WD shift switch system. Refer to TF-62, "
4WD Shift Switch" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. CHECK ACCELERATOR PEDAL POSITION SIGNAL CIRCUIT
Perform self diagnosis for ECM. Refer to EC-49, "
Emission-related Diagnostic Information" .
Is any malfunction deteced by self-diagnosis?
YES >> Check the malfunctioning system.
NO >> GO TO 4.
4. CHECK SYSTEM FOR CLUTCH PRESSURE SOLENOID
Perform trouble diagnosis for clutch pressure solenoid system. Refer to TF-105, "
Clutch Pressure Switch" .
OK or NG
OK >> GO TO 5.
NG >> Repair or replace damaged parts.
5. SYMPTOM CHECK
Check again.
OK or NG
OK >> Inspection End.
NG >> GO TO 6.
6. CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to TF-35, "
Transfer Control Unit Input/Output Signal Ref-
erence Values" .
OK or NG
OK >> GO TO 7.
NG >> Check transfer control unit pin terminals for damage or loose connection with harness connector. If any items are damaged, repair or replace damaged parts.

TROUBLE DIAGNOSIS FOR SYMPTOMSTF-131
CE F
G H
I
J
K L
M A
B
TF
Revision: November 2009 2006 QX56
7. CHECK TRANSFER INNER PARTS
1. Disassemble transfer assembly. Refer to TF-146, "
Disassembly and Assembly" .
2. Check transfer inner parts.
OK or NG
OK >> Inspection End.
NG >> Repair or replace damaged parts.
4WD System Does Not OperateEDS002HU
SYMPTOM:
The vehicle cannot be put into 4WD mode. (Hydraulic system failure)
DIAGNOSTIC PROCEDURE
1. CHECK SYSTEM FOR 4WD SHIFT SWITCH
Perform trouble diagnosis for 4WD shift switch system. Refer to TF-62, "
4WD Shift Switch" .
OK or NG
OK >> GO TO 2.
NG >> Repair or replace damaged parts.
2. CHECK SYSTEM FOR CLUTCH PRESSURE SWITCH
Perform trouble diagnosis for clutch pressure switch system. Refer to TF-105, "
Clutch Pressure Switch" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. SYMPTOM CHECK
Check again.
OK or NG
OK >> Inspection End.
NG >> GO TO 4.
4. CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to TF-35, "
Transfer Control Unit Input/Output Signal Ref-
erence Values" .
OK or NG
OK >> GO TO 5.
NG >> Check transfer control unit pin terminals for damage or loose connection with harness connector. If any items are damaged, repair or replace damaged parts.
5. CHECK TRANSFER INNER PARTS
1. Disassemble transfer assembly. Refer to TF-146, "
Disassembly and Assembly" .
2. Check transfer inner parts.
OK or NG
OK >> Inspection End.
NG >> Repair or replace damaged parts.