2006 INFINITI QX56 sensor

AT-78
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
48
Others Shift point is low in “
D”
position. ON vehicle1. Vehicle speed sensor A/T and vehicle speed sensor MTR
AT- 111
,
AT- 1 3 2
2. Accelerator pedal position sensor AT- 1 2 4
3. CAN communication line AT- 9 6
4. Control valve with TCMAT- 2 3 0
49Judder occurs during
lock-up. ON vehicle1. Fluid level and state
AT- 5 1
2. Engine speed signalAT- 11 6
3. Turbine revolution sensorAT- 1 0 9
4. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 111,
AT- 1 3 2
5. Accelerator pedal position sensor AT- 1 2 4
6. CAN communication line AT- 9 6
7. Torque converter clutch solenoid valveAT- 11 8
8. Control valve with TCMAT- 2 3 0
OFF vehicle 9. Torque converter AT- 2 6 4
50Strange noise in “
R”
position. ON vehicle
1. Fluid level and state
AT- 5 1
2. Engine speed signalAT- 11 6
3. CAN communication line AT- 9 6
4. Control valve with TCMAT- 2 3 0
OFF vehicle5. Torque converter
AT- 2 6 4
6. Oil pump assemblyAT- 2 8 2
7. Gear systemAT- 2 5 0
8. High and low reverse clutchAT- 2 9 6
9. Reverse brakeAT- 2 6 4
51Strange noise in “
N”
position. ON vehicle
1. Fluid level and state
AT- 5 1
2. Engine speed signalAT- 11 6
3. CAN communication line AT- 9 6
4. Control valve with TCMAT- 2 3 0
OFF vehicle5. Torque converter
AT- 2 6 46. Oil pump assemblyAT- 2 8 2
7. Gear systemAT- 2 5 0
52Strange noise in “
D”
position. ON vehicle
1. Fluid level and state
AT- 5 1
2. Engine speed signalAT- 11 6
3. CAN communication line AT- 9 6
4. Control valve with TCMAT- 2 3 0
OFF vehicle5. Torque converter
AT- 2 6 4
6. Oil pump assemblyAT- 2 8 2
7. Gear systemAT- 2 5 0
8. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 7
, AT- 1 8
.) AT- 2 6 4
No. Items
Symptom Condition Diagnostic ItemReference
page

AT-80
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
56
Others Maximum speed low.
ON vehicle
1. Fluid level and state
AT- 5 1
2. Line pressure testAT- 5 2
3. Accelerator pedal position sensorAT- 1 2 4
4. CAN communication line AT- 9 6
5. Direct clutch solenoid valveAT- 1 4 7
6. Control valve with TCMAT- 2 3 0
OFF vehicle7. Torque converter
AT- 2 6 4
8. Oil pump assemblyAT- 2 8 2
9. Input clutchAT- 2 8 6
10. Gear systemAT- 2 5 0
11. High and low reverse clutchAT- 2 9 6
12. Direct clutchAT- 2 9 8
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 7
, AT- 1 8 .) AT- 2 6 4
14 Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to
AT- 1 7
, AT- 1 8
.) AT- 2 6 4
57
Extremely large
creep. ON vehicle1. Engine idle speed
EC-76

2. CAN communication line AT- 9 6
3. ATF pressure switch 5AT- 1 6 3
OFF vehicle 4. Torque converter AT- 2 6 4
58With selector lever in
“
P ” position, vehicle
does not enter parking
condition or, with
selector lever in
another position, park-
ing condition is not
cancelled.
Refer to AT-180, "
In
“P” Position, Vehicle
Moves When Pushed"
. ON vehicle
1. PNP switch
AT- 1 0 5
2. Control cable adjustmentAT- 2 2 7
OFF vehicle 3. Parking pawl components AT- 2 5 0
59Vehicle runs with
transmission in
“P ”
position. ON vehicle1. PNP switch
AT- 1 0 5
2. Fluid level and state AT- 5 1
3. Control cable adjustmentAT- 2 2 7
4. Control valve with TCMAT- 2 3 0
5. Parking pawl componentsAT- 2 5 0
OFF vehicle 6. Gear system AT- 2 5 0
No. ItemsSymptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSISAT-81
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
60
Others Vehicle runs with
transmission in
“N ”
position.
Refer to AT-181, "In
“N” Position, Vehicle
Moves" . ON vehicle
1. PNP switch
AT-105
2. Fluid level and state AT- 5 1
3. Control cable adjustmentAT-227
4. Control valve with TCMAT-230
OFF vehicle5. Input clutch
AT-286
6. Gear systemAT-250
7. Direct clutchAT-298
8. Reverse brakeAT-264
9. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 7
, AT- 1 8 .) AT-264
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 7
, AT- 1 8
.) AT-264
61Engine does not start
in
“N ” or “P ” position.
Refer to AT-179, "Engine Cannot Be
Started In “P” or “N”
Position" . ON vehicle
1. Ignition switch and starter
PG-4
, SC-
10
2. Control cable adjustment
AT-227
3. PNP switchAT-105
62Engine starts in posi-
tions other than “
N” or
“ P ”. ON vehicle1. Ignition switch and starter
PG-4
, SC-
10
2. Control cable adjustment
AT-227
3. PNP switchAT-105
63Engine stall. ON vehicle1. Fluid level and state
AT- 5 1
2. Engine speed signalAT- 11 6
3. Turbine revolution sensorAT-109
4. Torque converter clutch solenoid valve AT- 11 8
5. CAN communication line AT- 9 6
6. Control valve with TCMAT-230
OFF vehicle 7. Torque converter AT-264
64Engine stalls when
select lever shifted
“N ”
→ “ D ”, “ R”. ON vehicle1. Fluid level and state
AT- 5 1
2. Engine speed signalAT- 11 6
3. Turbine revolution sensorAT-109
4. Torque converter clutch solenoid valve AT- 11 8
5. CAN communication line AT- 9 6
6. Control valve with TCMAT-230
OFF vehicle 7. Torque converter AT-264
No. ItemsSymptom Condition Diagnostic ItemReference
page

AT-82
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
65 OthersEngine speed does
not return to idle.
Refer to
AT-208,
"Engine Speed Does
Not Return to Idle" .ON vehicle 1. Fluid level and state
AT- 5 1
2. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 6 3,
AT- 1 4 7
3. ATF pressure switch 1 and front brake solenoid valve AT- 1 5 9,
AT- 1 4 3
4. Accelerator pedal position sensor AT- 1 2 4
5. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 111,
AT- 1 3 2
6. CAN communication line AT- 9 6
7. Control valve with TCMAT- 2 3 0
OFF vehicle8. Front brake (brake band)
AT- 2 6 49. Direct clutchAT- 2 9 8
No. ItemsSymptom Condition Diagnostic ItemReference
page

AT-84
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
CONSULT-II Function (A/T)ECS00CEP
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II REFERENCE VALUE
NOTICE:
1. The CONSULT-II electrically displays shift timing and lock-up timing (that is, operation timing of each sole-
noid).
Check for time difference between actual shift timing and the CONSULT-II display. If the difference is
noticeable, mechanical parts (except solenoids, sensors, etc.) may be malfunctioning. Check mechanical
parts using applicable diagnostic procedures.
2. Shift schedule (which implies gear position) displayed on CONSULT-II and that indicated in Service Man- ual may differ slightly. This occurs because of the following reasons:
–Actual shift schedule has more or less tolerance or allowance,
–Shift schedule indicated in Service Manual refers to the point where shifts start, and
–Gear position displayed on CONSULT-II indicates the point where shifts are completed.
3. Display of solenoid valves on CONSULT-II changes at the start of shifting, while gear position is displayed upon completion of shifting (which is computed by TCM).
TCM diagnostic mode Description
WORK SUPPORT Supports inspections and adjustments. Commands are transmitted to the TCM for setting the status
suitable for required operation, input/output signals are received from the TCM and received data is
displayed.
SELF-DIAG RESULTS Displays TCM self-diagnosis results.
DATA MONITOR Displays TCM input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
FUNCTION TEST Conducted by CONSULT-II instead of a technician to determine whether each system is
“OK ” or
“ NG ”.
ECU PART NUMBER TCM part number can be read.
Item name Condition Display value (Approx.)
ATF TEMP SE 1 0°C (32 ° F) - 20 °C (68 °F) - 80 °C (176 °F) 3.3 - 2.7 - 0.9 V
ATF TEMP SE 2 3.3 - 2.5 - 0.7 V
TCC SOLENOID When perform slip lock-up
0.2 - 0.4 A
When perform lock-up 0.4 - 0.6 A
SLCT LVR POSI Selector lever in
“N ”,“ P ” position. N/P
Selector lever in “R ” position. R
Selector lever in “D ” position. D
Selector lever in “4 ” position. 4
Selector lever in “3 ” position. 3
Selector lever in “2 ” position. 2
Selector lever in “1 ” position. 1
VHCL/S SE ·A/T During driving Approximately matches the
speedometer reading.
ENGINE SPEED Engine running Closely matches the tachometer
reading.
LINE PRES SOL During driving 0.2 - 0.6 A
TURBINE REV During driving (lock-up ON) Approximately matches the
engine speed.
VHCL/S SE ·MTR During driving Approximately matches the
speedometer reading.

TROUBLE DIAGNOSISAT-87
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
2. Touch “SELF-DIAG RESULTS ”.
Display shows malfunction experienced since the last erasing
operation.
Display Items List
X: Applicable, —: Not applicable
BCIA0031E
Items (CONSULT-II
screen terms) Malfunction is detected when... TCM self-
diagnosis OBD-II (DTC)
“ A/T ” with
CONSULT-II MIL indicator
lamp*1,
“ ENGINE ” with
CONSULT-II or
GST
CAN COMM CIRCUIT

When a malfunction is detected in CAN communications U1000 U1000
STARTER RELAY/
CIRC

If this signal is ON other than in P or N position, this is judged to be a
malfunction.
(And if it is OFF in P or N position, this too is judged to be a malfunc-
tion.) P0615
—
TCM

TCM is malfunctioning. P0700 P0700
PNP SW/CIRC

PNP switch 1-4 signals input with impossible pattern

“ P ” position is detected from N position without any other position
being detected in between. P0705 P0705
TURBINE REV S/CIRC

TCM does not receive the proper voltage signal from the sensor.

TCM detects an irregularity only at position of 4th gear for turbine revo-
lution sensor 2. P0717 P0717
VEH SPD SEN/CIR AT
(Revolution sensor)

Signal from vehicle speed sensor A/T (Revolution sensor) not input
due to cut line or the like

Unexpected signal input during running

After ignition switch is turned ON, unexpected signal input from vehicle
speed sensor MTR before the vehicle starts moving P0720 P0720
ENGINE SPEED SIG

TCM does not receive the CAN communication signal from the ECM. P0725 —
TCC SOLENOID/CIRC

Normal voltage not applied to solenoid due to cut line, short, or the like P0740 P0740
A/T TCC S/V FNCTN

A/T cannot perform lock-up even if electrical circuit is good.

TCM detects as irregular by comparing difference value with slip rota-
tion. P0744 P0744*2
L/PRESS SOL/CIRC

Normal voltage not applied to solenoid due to cut line, short, or the like

TCM detects as irregular by comparing target value with monitor value. P0745 P0745
TP SEN/CIRC A/T

TCM does not receive the proper accelerator pedal position signals
(input by CAN communication) from ECM. P1705 P1705
ATF TEMP SEN/CIRC

During running, the ATF temperature sensor signal voltage is exces-
sively high or low P1710 P0710
VEH SPD SE/CIR ·MTR

Signal (CAN communication) from vehicle speed sensor MTR not input
due to cut line or the like

Unexpected signal input during running P1721
—
A/T INTERLOCK

Except during shift change, the gear position and ATF pressure switch
states are monitored and comparative judgement made. P1730 P1730

AT-90
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
DATA MONITOR MODE
Operation Procedure
1. Perform “CONSULT-II SETTING PROCEDURE ”. Refer to AT- 8 6 , "CONSULT-II SETTING PROCEDURE"
.
2. Touch “DATA MONITOR ”.
NOTE:
When malfunction is detected, CONSULT-II performs
“REAL-TIME DIAGNOSIS”. Also, any malfunction detected
while in this mode will be displayed at real time.
Display Items List
X: Standard, —: Not applicable
BCIA0031E
Monitored item (Unit) Monitor Item Selection
Remarks
ECU
INPUT
SIGNALS MAIN SIG-
NALS SELEC-
TION
FROM
MENU
VHCL/S SE ·A/T (km/h) XXX Revolution sensor
VHCL/S SE ·MTR (km/h) X— X
ACCELE POSI (0.0/8) X— X Accelerator pedal position signal
THROTTLE POSI (0.0/8) XXXDegree of opening for accelerator recognized by
the TCM
For fail-safe operation, the specific value used
for control is displayed.
CLSD THL POS (ON-OFF display) X— X
Signal input with CAN communications
W/O THL POS (ON-OFF display) X— X
BRAKE SW (ON-OFF display) X— X Stop lamp switch
GEAR —XX Gear position recognized by the TCM updated
after gear-shifting
ENGINE SPEED (rpm) XXX
TURBINE REV (rpm) XXX
OUTPUT REV (rpm) XXX
GEAR RATIO —XX
TC SLIP SPEED (rpm) —XX Difference between engine speed and torque
converter input shaft speed
F SUN GR REV (rpm) ——X
F CARR GR REV (rpm) ——X
ATF TEMP SE 1 (V) X— X
ATF TEMP SE 2 (V) X— X
ATF TEMP 1 ( °C) —XX
ATF TEMP 2 ( °C) —XX
BATTERY VOLT (V) X— X
ATF PRES SW 1 (ON-OFF display) XXX (for FR/B solenoid)
ATF PRES SW 2 (ON-OFF display) XXX (for LC/B solenoid)
ATF PRES SW 3 (ON-OFF display) XXX (for I/C solenoid)
ATF PRES SW 5 (ON-OFF display) XXX (for D/C solenoid)

DTC P0615 START SIGNAL CIRCUITAT-103
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
3. CHECK TERMINAL CORD ASSEMBLY
1. Remove control valve with TCM. Refer to AT- 2 3 0 , "
Control Valve With TCM and A/T Fluid Temperature
Sensor 2" .
2. Disconnect A/T assembly harness connector and TCM connector.
3. Check continuity between A/T assembly harness connector ter- minal and TCM connector terminal.
4. If OK, check harness for short to ground and short to power.
5. Reinstall any part removed.
OK or NG
OK >> GO TO 4.
NG >> Replace open circuit or short to ground and short to power in harness or connectors.
4. DETECT MALFUNCTIONING ITEM
Check the following items:

Starter relay, Refer to SC-10, "STARTING SYSTEM" .

IPDM E/R, Refer to PG-18, "IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)" .
OK or NG
OK >> Replace the control valve with TCM. Refer to AT- 2 3 0 , "Control Valve With TCM and A/T Fluid
Temperature Sensor 2"
NG >> Repair or replace damaged parts.
5. CHECK DTC
Perform “DTC Confirmation Procedure ”.

Refer to AT- 1 0 0 , "DTC Confirmation Procedure" .
OK or NG
OK >> INSPECTION END
NG >> GO TO 2.
Item Connector Terminal Continuity
A/T assembly harness con-
nector F9
9
Ye s
TCM connector F5028
SCIA5440E