2006 INFINITI M35 low beam

ACS-40
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2006 January2006 M35/M45
14ECM CIRCUIT
[C1A14]
ECM malfunction.
Accelerator pedal position sensor
malfunction.
ICC sensor integrated unit mal-
function.ACS-55
15GEAR POSITION
[C1A15]
TCM malfunction.
A/T turbine revolution sensor mal-
function.
A/T vehicle speed sensor mal-
function.ACS-56
16RADAR STAIN
[C1A16]ICC sensor integrated unit body
window has contamination.ACS-57
18LASER AIMING INCMP
[C1A18]Laser beam aiming of ICC sensor
integrated unit is not adjusted.ACS-57
21UNIT HIGH TEMP
[C1A21]Temperature around ICC sensor
integrated unit is excessively high.ACS-57
24NP RANGE
[C1A24]
Park/neutral position switch mal-
function.
TCM malfunction.ACS-58
25 SHIFT RANGE IND
[C1A25]TCM malfunction.ACS-58
26ECD MODE MALF
[C1A26]
ABS actuator and electric unit
(control unit) malfunction.
ICC sensor integrated unit mal-
function.ACS-59
27ECD PWR SUPLY CIR
[C1A27]
ABS actuator and electric unit
(control unit) power supply voltage
is excessively low.
ABS actuator and electric unit
(control unit) malfunction.ACS-59
55NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.No malfunction item has been
detected. —
100CAN COMM CIRCUIT
[U1000]
ICC sensor integrated unit detects
CAN communication malfunction.ACS-60
11 0CONTROL UNIT (CAN)
[U1010]
ICC sensor integrated unit detects
malfunction by CAN initial diagno-
sis.ACS-60
DTC
No.CONSULT-II
screen termsICC
system
warning
lampFail-safe
Malfunctions detected where...Refer-
ence
page Vehicle-
to-
vehicle
d i s t a n c e
control
modeConven-
tional
(fixed
speed)
cruise
control
modeBrake
assist
(with
preview
function)

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-63
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2006 January2006 M35/M45
Symptom 2: ICC System Cannot Be Set (MAIN Switch Turns ON/OFF)NKS004DL
The ICC system cannot be set in the following cases.
When the vehicle speed is not in range of approx. 25 MPH (40 km/h) to 90 MPH (144 km/h).
When the A/T selector lever is in “N”.
When A/T mode switch is at the snow mode position.
While the brake is in operation.
When wiper switch is at LOW/HI position.
1. CHECK CAUSE OF AUTOMATIC CANCELLATION
With CONSULT-II
With “CAUSE OF AUTO-CANCEL” in “WORK SUPPORT” at “ICC”, check if any cause of cancellation is
found.
Is any cause found?
YES >> Cancel with appropriate cause, and go to specified diagnosis.
“OPE SW VOLT CIRC”: Refer to ACS-47, "DTC 6 OPERATION SW CIRC" .
“VHCL SPD UNMATCH”: Refer to ACS-42, "DTC 3 VHCL SPEED SE CIRC" .
“IGN LOW VOLT”: Refer to ACS-41, "DTC 1 POWER SUPPLY CIR, DTC 2 POWER SUPPLY
CIR 2" .
“ECM CIRCUIT”: Refer to ACS-55, "DTC 14 ECM CIRCUIT" .
NO >> GO TO 2.
2. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
With CONSULT-II
Perform self-diagnosis to check for malfunctioning items.
Is malfunction indicated?
YES >> 1. Repair or replace applicable item. Refer to ACS-39, "Diagnostic Trouble Code (DTC) Chart" .
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 3.
3. CHECK SWITCHES AND VEHICLE SPEED SIGNAL
With CONSULT-II
With “ICC” “DATA MONITOR”, check if switches and vehicle speed signal operate normally. Refer to ACS-30,
"DATA MONITOR" .
VHCL SPEED SE
D RANGE SW
BRAKE SW
SET/COAST SW
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and Perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> Check items which do not function normally.
VHCL SPEED SE. Refer to ACS-42, "DTC 3 VHCL SPEED SE CIRC" .
D RANGE SW. Refer to ACS-64, "Symptom 4: ICC System Is Not Cancelled When the A/T
Selector Lever Is In Other Than “D” and “M”" .
BRAKE SW. Refer to ACS-43, "DTC 5 BRAKE SW/STOP L SW" .
SET/COAST SW. Refer to ACS-47, "DTC 6 OPERATION SW CIRC" .

ACS-64
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2006 January2006 M35/M45
Symptom 3: ICC System Cannot Be Operated by CANCEL Switch, RESUME/
ACCELERATE Switch or DISTANCE Switch
NKS004DM
RESUME does not function in the following cases.
When MAIN switch is turned off once.
When the vehicle speed is less than 25 MPH (40 km/h).
1. CHECK SWITCHES
With CONSULT-II
With “ICC” “DATA MONITOR”, check if switches operate normally.
“RESUME/ACC SW”
“CANCEL SW”
“DISTANCE SW”
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> GO TO 2.
2. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
With CONSULT-II
1. Perform self-diagnosis.
2. Check if “DTC 100 CAN COMM CIRCUIT” is indicated.
Is it indicated?
YES >> CAN communication inspection. Refer to ACS-60, "DTC 100 CAN COMM CIRCUIT" .
NO >> ICC steering switch inspection. Refer to ACS-47, "
DTC 6 OPERATION SW CIRC" .
Symptom 4: ICC System Is Not Cancelled When the A/T Selector Lever Is In
Other Than “D” and “M”
NKS004DN
1. CHECK D RANGE SWITCH
With CONSULT-II
With “ICC” “DATA MONITOR”, check if “D RANGE SW” and “NP RANGE SW” operate normally.
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> GO TO 2.
2. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
With CONSULT-II
1. Perform self-diagnosis.
2. Check if “DTC 100 CAN COMM CIRCUIT” is indicated.
Is it indicated?
YES >> CAN communication inspection. Refer to ACS-60, "DTC 100 CAN COMM CIRCUIT" .
NO >> GO TO 3.

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-65
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2006 January2006 M35/M45
3. CHECK D RANGE SWITCH
With CONSULT-II
With “A/T” “DATA MONITOR”, check if “SLCT LVR POSI” operates normally.
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> 1. Perform “A/T” self-diagnosis. Refer to AT- 9 0 , "
CONSULT-II Function (A/T)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
Symptom 5: Chime Does Not SoundNKS004DO
The chime may not sound occasionally in the following cases even if the distance from the vehicle ahead is
short:
When the speed difference from that of the vehicle ahead is small (both vehicles driving at similar speed).
When the vehicle ahead drives at faster speed (the actual distance is increasing).
When depressing the accelerator pedal.
Chime does not sound when the vehicle is not driving.
Chime does not sound when the system does not detect any vehicle ahead. (Diagnose the conditions
under which the system is detecting the vehicle ahead and when the system is malfunctioning. If there is
any malfunction in detecting the vehicle ahead, check the system following the ACS-66, "
Symptom 7: ICC
System Frequently Cannot Detect the Vehicle Ahead/ Detection Zone Is Short" ).
1. CHECK ICC WARNING CHIME
With CONSULT-II
With “ICC” “ACTIVE TEST”, check if “ICC BUZZER” operates normally.
OK or NG
OK >> 1. Determine preceding vehicle detection status when malfunction occurred. If chime should have
sounded: after replacing ICC sensor integrated unit and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test, and then perform self-diagnosis of ICC sys-
tem again.
NG >> GO TO 2.
2. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
With CONSULT-II
1. Perform self-diagnosis.
2. Check if “DTC 100 CAN COMM CIRCUIT” is indicated.
Is it indicated?
YES >> CAN communication inspection. Refer to ACS-60, "DTC 100 CAN COMM CIRCUIT" .
NO >> GO TO 3.
3. CHECK UNIFIED METER AND A/C AMP.
With CONSULT-II
Perform “METRE A/C AMP” self-diagnosis. Refer to DI-31, "
CONSULT-II Function (METER A/C AMP)" .
Is malfunction indicated?
YES >> 1. Repair or replace applicable item.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 4.

ACS-66
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2006 January2006 M35/M45
4. CHECK CHIME OPERATION
With CONSULT-II
1. Select “BUZZER” on “BCM”.
2. With “BUZZER” “ACTIVE TEST”, check if “IGN KEY WARN ALM” and “LIGHT WARN ALM” operate nor-
mally.
Does chime sound?
YES >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> 1. Replace combination meter.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
Symptom 6: Driving Force Is HuntingNKS004DP
1. PERFORM ECM SELF-DIAGNOSIS
With CONSULT-II
Perform “ENGINE” self-diagnosis. Refer to EC-133, "
CONSULT-II Function (ENGINE)" (for VQ35DE) or EC-
846, "CONSULT-II Function (ENGINE)" (for VK45DE).
Is malfunction indicated?
YES >> 1. Repair or replace applicable item.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> Refer to ACS-66, "
Symptom 7: ICC System Frequently Cannot Detect the Vehicle Ahead/ Detec-
tion Zone Is Short" .
Symptom 7: ICC System Frequently Cannot Detect the Vehicle Ahead/ Detection
Zone Is Short
NKS004DQ
The detection function may become unstable in the following cases.
When the reflector of the vehicle ahead is deficient/ not clean enough to reflect the radar.
When driving a road with extremely sharp corners.
When the sensor cannot detect the reflector of the vehicle ahead as the vehicle ahead is passing a hill or
passing the peak.
1. VISUAL CHECK 1
Check ICC sensor integrated unit body window for contamination and foreign materials.
Is it found?
YES >> 1. If any, remove them.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 2.
2. VISUAL CHECK 2
Check ICC sensor integrated unit body window for cracks and scratches.
Is it found?
YES >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 3.

COMBINATION METERS
DI-9
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2006 January2006 M35/M45
FA I L - S A F E
Combination meter performs fail-safe operation when unified meter and A/C amp. communication is malfunc-
tion.
Solution for communication error between the unified meter & A/C amp. and combination meter
Function Specifications
Speedometer
Reset to zero by suspending communication. Tachometer
Fuel gauge
Water temperature gauge
Illumination control Meter illumination When suspending communication, change to nighttime mode.
Dot matrix LCDPush engine starter
The display turns off by suspending communication. A/T position
ICC system
Buzzer The buzzer turns off by suspending communication.
Warning lamp/indicator lampABS warning lamp
The lamp turns on by suspending communication. Brake warning lamp
CRUISE warning lamp
VDC OFF indicator lamp
SLIP indicator lamp
A/T CHECK warning lamp
The lamp turns off by suspending communication. AWD warning lamp
Oil pressure warning lamp
Door warning lamp
Malfunction indicator lamp
CRUISE indicator lamp
SET indicator lamp
Low tire pressure warning lamp
AFS OFF indicator lamp
Front fog indicator lamp
High beam indicator
Turn signal indicator lamp
Key warning lamp

DI-28
UNIFIED METER AND A/C AMP
Revision: 2006 January2006 M35/M45
UNIFIED METER AND A/C AMPPFP:27760
System DescriptionNKS003UG
For the unified meter and A/C amp., the signal required for controlling the combination meter are integrated in
the A/C auto amp.
COMBINATION METER CONTROL FUNCTION
Unified meter and A/C amp. inputs necessary information for combination meter from each unit with CAN
communication and so on.
Unified meter and A/C amp. outputs signals with communication line (TX, RX) between unified meter and
A/C amp. and combination meter.
Unified meter and A/C amp. corresponds a CONSULT-II function (self-diagnostic results, CAN diagnostic
support monitor and data monitor).
Input/output Signals
Between unified meter and A/C amp. and combination meter.
Unit Input from combination meter Output to combination meter
Unified meter and A/C amp.
Refuel status signal
Low-fuel warning lamp condition signal
Delivery destination data signal
Combination meter receive error signal
Combination meter specifications signal
Odo date signal
Vehicle speed signal
Turn indicator signal
High beam request signal
Ring illumination request signal
Position light request signal
Front fog lamp request signal
SET indicator lamp signal
CRUISE indicator lamp signal
Engine speed signal
Fuel level sensor signal (resistance value)
Engine coolant temperature signal
CAN communication condition signal of A/T
A/T position indicator signal
Manual mode indicator signal
A/T CHECK warning lamp signal
AWD warning lamp signal
Low tire pressure warning lamp signal
VDC OFF indicator lamp signal
SLIP indicator lamp signal
ABS warning lamp signal
Brake warning lamp signal
Malfunction indicator lamp signal
Oil pressure switch signal
Door switch signal
Buzzer request signal
ICC warning lamp signal
Meter display signal
AFS OFF indicator signal

UNIFIED METER AND A/C AMP
DI-33
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2006 January2006 M35/M45
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch either “MAIN SIGNALS” or “SELECTION FROM MENU” on the “DATA MONITOR” screen.
3. When “SELECTION FROM MENU” is selected, touch individual items to be monitored. When “MAIN SIG-
NALS” is selected, main items will be monitored.
4. Touch “START”.
5. Touch “RECORD” while monitoring, then the status of the moni-
tored item can be recorded. To stop recording, touch “STOP”.
Display Item List
X: Applicable MAIN SIGNALS Monitors main signals.
SELECTION FROM MENU Selects and monitors individual signal.
SKIA4957E
Display item [Unit]MAIN
SIGNALSSELECTION
FROM MENUDescription
SPEED METER [km/h] or [mph] X XDisplays the value of vehicle speed signal, which is input from ABS
actuator and electric unit (control unit).
SPEED OUTPUT [km/h] or [mph] X XDisplays the value of vehicle speed signal, which is transmitted to
each unit with CAN communication.
TACHO METER [rpm] X X Displays the value of engine speed signal, which is input from ECM.
W TEMP METER [
C] or [F] X XDisplays the value of engine coolant temperature signal, which is
input from ECM.
FUEL METER [lit.] X XDisplays the value, which processes a resistance signal from fuel
gauge.
DISTANCE [km] or [mile] X XDisplays the value, which is calculated by vehicle speed signal from
ABS actuator and electric unit (control unit), fuel gauge and fuel
consumption from ECM.
FUEL W/L [ON/OFF] X X Displays [ON/OFF] condition of low-fuel warning lamp.
MIL [ON/OFF] X Displays [ON/OFF] condition of malfunction indicator lamp.
AIR PRES W/L [ON/OFF] X Displays [ON/OFF] condition of low tire pressure warning lamp.
SEAT BELT W/L [ON/OFF] X Displays [ON/OFF] condition of seat belt warning lamp.
BUZZER [ON/OFF] X X Displays [ON/OFF] condition of buzzer.
DOOR W/L [ON/OFF] X Displays [ON/OFF] condition of door warning lamp.
HI-BEAM IND [ON/OFF] X Displays [ON/OFF] condition of high beam indicator.
TURN IND [ON/OFF] X Displays [ON/OFF] condition of turn indicator.
FR FOG IND [ON/OFF] X Displays [ON/OFF] condition of front fog indicator.
OIL W/L [ON/OFF] X Displays [ON/OFF] condition of oil pressure warning lamp.
VDC/TCS IND [ON/OFF] X Displays [ON/OFF] condition of VDC/TCS OFF indicator lamp.
ABS W/L [ON/OFF] X Displays [ON/OFF] condition of ABS warning lamp.
SLIP IND [ON/OFF] X Displays [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L [ON/OFF] X Displays [ON/OFF] condition of brake warning lamp. *
KEY Y/G W/L [ON/OFF] X Displays [ON/OFF] condition of key warning lamp.