2006 ACURA CSX keyless



(#' .
)
µ
µ µ
µ
µ
µ
DTC B1925:
YES
NO YES
NO
YES
NO
22-319
IGNITION KEY SWITCH 6P CONNECTOR
GND
IG KEY SW
IGNITION KEY SWITCH 6P CONNECTOR GND
IG KEY SW
Ignition Key Switch Signal Error
NOTE:
 If you are troubleshooting multiple DTCs, be sure to follow the instructions in B-CAN System Diagnosis
Test Mode A (see page 22-93).
 If the vehicle is equipped with an ACURA ACCESSORY remote starter, this DTC is normal no
further diagnosis is necessary.
1. Clear the DTCs with the HDS.
2. Turn the ignition switch to LOCK (0) and remove the ignition key.
3. Insert the ignition key into the ignition switch, and turn the ignition switch to ON (II).
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for loose or poor connections at the
immobilizer-keyless control unit 7P c onnector,
under-dash fuse/relay box 20P connector R, and at
the ignition key switch 6P connector.
5. Turn the ignition switch to LOCK (0) and remove the ignition key.
6. Disconnect the ignition key switch 6P connector. 7. At the ignition key switch side, check for continuity
between ignition key switch 6P connector terminals
No. 1 and No. 2.
Faulty ignition key switch or short to ground,
replace the steering lock assembly (see page 17-14).
Go to step 8.
8. Insert the ignition key into the ignition switch.
9. At the ignition key switch side, check for continuity between ignition key switch 6P connector terminals
No. 1 and No. 2.
Go to step 10.
Faulty ignition key switch, replace the
steering lock assembly (see page 17-14).
(cont’d)
Terminal side of male terminals
Terminal side of male terminals
Is DTC B1925 indicated? Is there continuity?
Is there continuity?
08/08/21 14:36:59 61SNR030_220_0321
ProCarManuals.com
DYNOMITE -2009-


µ
µ µ
µ
YES
NO YES
NO
22-320Immobilizer System
DTC Troubleshooting (cont’d)
IGNITION KEY SWITCH 6P CONNECTOR
IMMOBILIZER-KEYLESS CONTROL UNIT 7P CONNECTOR IG KEY SW (PNK)
IG KEY SW (PNK) IMMOBILIZER-KEYLESS CONTROL UNIT 7P CONNECTOR
IG KEY SW (PNK)
10. Disconnect the immobilizer-keyless control unit 7Pconnector.
11. Check for continuity between immobilizer-keyless control unit 7P connector terminal No. 6 and
ignition key switch 6P connector terminal No. 1.
Go to step 12.
Repair an open in the wire and check under-
dash fuse/relay box 20P connector R. 12. Check for continuity between immobilizer-keyless
control unit 7P connector terminal No. 6 and body
ground.
Repair a short to ground in the wire or
substitute a known-good under-dash fuse/relay box,
and recheck. If the symptom/indication goes away,
replace under-dash fuse/relay box.
Replace the immobilizer-keyless control unit
(see page 22-332).
Wire side of female terminals
Wire side of female terminals Wire side of female terminals
Is there continuity?
Is there continuity?
08/08/21 14:36:59 61SNR030_220_0322
ProCarManuals.com
DYNOMITE -2009-

Î
How to Troubleshoot
Symptom Troubleshooting of an open Power Supply and Ground Circuit
22-322Immobilizer System
Symptom Troubleshooting Information (cont’d)
Immobilizer
Indicator
Symptom
Line Error Engine StartKey
RegistrationTester
Communication
Keyless Operation
VBU line open
or short Comes on,
then goes off.
Possible
Possible Possible
Impossible
1
IG1 line open
or short Blinking Impossible
Impossible
Impossible
Possible
2
Blinking Impossible Impossible
Possible
Possible
IMOCD line
open or short
3
4 Immobilizer:
Possible
Keyless:
Impossible Impossible
Possible Possible
Comes on,
then goes off.
B-CAN line
open or short
Comes on,
then goes off. Impossible
Impossible
Possible
Possible
5
KEYSW line
short to groundGND (LG) line
open
6
7 (in spite of the key is
in the ignition switch)
Possible
Possible Possible Possible
Comes on,
then goes off.
KEYSW line
open
K-LINE line
open or short
Blinking Impossible Impossible
Impossible ImpossibleImpossible
Cause of
Malfunction
Terminal
No.
NOTE: If the HDS does not communicate with the vehicle, troubleshoot the DLC circuit (see page 11-
204).
1. Do the PGM-FI system DTCs check. If there are any DTCs, troubleshoot the indicated DTC.
2. Do the Body Electrical DTCs check. If there are any DTC, troubleshoot the indicated DTC.
3. Do the system check using the HDS. If there is a system check number, do the troubleshooting for the item indicated (see page 22-326).
4. Check the status log using the HDS. Troubleshoot the line with the highest counts (see page 22-328). If all the lines are ‘‘0’’ zero, the problem may not be caused by the immobilizer system, check for ignition or fuel problems.
NOTE: Once repaired, clear the status log by removing the back up power fuse, or disconnecting the battery.
If a malfunction occurs in the immobilizer circuit for the VBU, IG1 and GND (LG) lines, identify the lines to check with
this table.
08/08/21 14:37:00 61SNR030_220_0324
ProCarManuals.com
DYNOMITE -2009-



(#')
µ
µ
µ
µ µ
µ
µ
µ
Immobilizer indicator blinks
YES
NO
YES
NO YES
NO
YES
NO
22-324Immobilizer System
Symptom Troubleshooting (cont’d)
IMMOBILIZER-KEYLESS CONTROL UNIT 7P CONNECTOR
IG1 (YEL)
IMMOBILIZER-KEYLESS CONTROL UNIT 7P CONNECTOR LG (BLK)
NOTE: Before troubleshooting, check the items listed in
‘‘General Check before Troubleshooting’’.
1. Turn the ignition switch to LOCK (0).
2. Connect the HDS, then turn the ignition switch to ON (II).
3. Enter the IMMOBILIZER, then select the IMMOBILIZER SETUP.
4. Select the SYSTEM CHECK.
Troubleshoot the immob ilizer system
according to the result of the SYSTEM CHECK
(see page 22-326).
Go to step 5.
5. Turn the ignition switch to LOCK (0).
6. Enter the vehicle, and remove the ignition key from the ignition switch, then close the all doors.
7. Operate the keyless transmitter LOCK and UNLOCK several times in the vehicle.
Go to step 8.
Check for a poor ground (G 101) and/or an
open in the wire between immobilizer-keyless
control unit 7P connector terminal No. 7 and body
ground (G 101).
8. Turn the ignition switch to ON (II). 9. Measure the voltage between immobilizer-keyless
control unit 7P connector terminal No. 2 and body
ground.
Go to step 10.
Repair open in the YEL wire between the
under-dash fuse/relay box and the immob ilizer-
keyless control unit.
10. Measure the voltage between immobilizer-keyless control unit 7P connector terminal No. 7 and body
ground.
Repair poor connection or open between
immobilizer-keyless control unit 7P c onnector
terminal No. 7 and G101.
Replace the immobilizer-keyless control unit
(see page 22-332).
Wire side of female terminals
Wire side of female terminalsIs the SY ST EM CHECK indicated?
Do t he d oor l ock act uat or s w or k nor mal l y ? Is there battery voltage?
Is t her e 0.5 V or mor e?
08/08/21 14:37:00 61SNR030_220_0326
ProCarManuals.com
DYNOMITE -2009-

(#')(#')
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ µ
µ
Engine does not start with the immobilizer
key Immobilizer indicator does not go off
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO YES
NO
22-32522-325
NOTE: Before troubleshooting, check the items listed in
‘‘General Check before Tr
oubleshooting’’ and ‘‘How to
Troubleshoot’’ (see page 22-322).
1. Try to start the engine.
Intermittent failure, the system is OK at this
time. Check status log (see page 22-328).
Go to step 2.
2. Turn the ignition switch to LOCK (0).
3. Turn the ignition switch to ON (II), and check the immobilizer indicator.
Go to step 4.
Go to the immobilizer indicator blinks
troubleshooting (see page 22- 324).
4. Turn the ignition switch to START (III).
Go to step 5.
Go to Starting System and check the starter
motor (see page 4-6).
5. Try to start the engine with the immobilizer key.
Go to step 6.
Go to the PGM-FI System Symptom
Troubleshooting.
6. Wait for a few minutes with the engine running.
Go to the PGM-FI System Symptom
Troubleshooting.
The system is OK at this time. 1. Turn the ignition switch to LOCK (0).
2. Connect the HDS to the data link connector.
3. Turn the ignition switch to ON (II).
4. Enter IMMOBILIZER, then select the IMMOBILIZER
INFORMATION.
5. Do the SYSTEM CHECK with the HDS.
Replace the gauge control module (tach)
(see page 22-277).
Substitute a known-good immobilizer-keyless
control unit, then register it and recheck. If the
symptom goes away, replace the original
immobilizer-keyless control unit (see page 22-332).
Doestheenginestart?
Does t he i nd i cat or come on f or 2 second s, t hen gooff?
Does the starter motor run?Doestheenginestart?Doestheenginestop? Is N-1 OK indicated?
08/08/21 14:37:00 61SNR030_220_0327
ProCarManuals.com
DYNOMITE -2009-

(#')System
Check No. System Check Possible Cause
22-326Immobilizer System
System Check
1. Connect the HDS to the data link connector.
2. Turn the ignition switch to ON (II).
3. Monitor the SYSTEM CHECK in the IMMOBILIZER INFO with the HDS.
4. If the HDS displays NORMAL N-1, the immobilizer system is OK at this time, refer to the STATUS LOG. If the HDS
displays any other messages, check as follows:





















A-1 The key is not
registered This key is not registered in the immobilizer-keyless control unit. Try
to register keys using the HDS.
No communication between the antenna and the immobilizer key
because of interference from metal such as key chains/key rings/
other keys.
Low battery voltage.
A-2 Communication error between the
key and
immobilizer unit Intermittent interruption between transponder and immobilizer-
keyless control unit.
The immobilizer key type is incorrect
non-Acura key.
Key failure (transponder failure)
No communication between the antenna and the immobilizer key
because of interference from metal such as key chains/key rings/
other keys.
Low battery voltage.
A-3 No communication between the key
and immobilizer
unit The ignition switch was turned to ON (II) with a non-immob
ilizer key.
The immobilizer key type is incorrect non-Acura key.
Key failure (transponder failure)
No communication between the antenna and the immobilizer key
because of interference from metal such as key chains/key rings/
other keys.
Low battery voltage.
Immobilizer-keyless control unit failure
B-1 The ECM/PCM is not registered The ECM/PCM was not registered. Try to register the ECM/PCM
using the HDS.
No communication between the ECM/PCM and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the immobilizer-keyless control unit
and the ECM/PCM because of interference.
Open in the IG1 line
B-2 Error of communication
format in ECM/
PCM The ECM/PCM was not registered. Try to register the ECM/PCM
using the HDS.
No communication between the ECM/PCM and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the immobilizer-keyless control unit
and the ECM/PCM because of interference.
08/08/21 14:37:00 61SNR030_220_0328
ProCarManuals.com
DYNOMITE -2009-

System
Check No. System Check Possible Cause
22-327























C-1 The imoes unit is
not registered Imoes unit was not registered.
No communication between the imoes unit and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the imoes unit and the immobilizer-
keyless control unit because of interference.
C-2 Error of communication
format in imoes
unit Imoes unit was not registered.
No communication between the imoes unit and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the imoes unit and the immobilizer-
keyless control unit because of interference.
D-1 S-net line short Harness short from the ECM/PCM to the immobilizer-keyless control unit. (IMOCD (S-net) line short)
No communication between the ECM/PCM and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the immobilizer-keyless unit and the
ECM/PCM because of interference.
Immobilizer-keyless control unit failure
ECM/PCM failure
D-2 No communication between imoes
unit and
immobilizer unit Blown fuse
Harness open from the imoes unit to the immobilizer-keyless control
unit. (IMOCD (S-net) line open)
No communication between the imoes unit and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the imoes unit and the immobilizer-
keyless control unit because of interference.
Immobilizer-keyless control unit failure
Imoes unit failure
D-3 No communication between ECM/PCM
and immobilizer
unit Blown fuse
Harness open from the ECM/PCM to the immobilizer-keyless control
unit.
No communication between the ECM/PCM and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the immobilizer-keyless control unit
and the ECM/PCM because of interference.
Immobilizer-keyless control unit failure
ECM/PCM failure
E-1 Initial registration of immobilizer unit
is not completed The immobilizer-keyless control unit is not registered. Try to register
the immobilizer-keyless control unit using the HDS.
E-2
E-3
E-4
E-5
F-1 Special Mode Turn the ignition switch to ON (II) and to LOCK (0) with the registered key.
F-2
F-3
F-4
F-5
08/08/21 14:37:00 61SNR030_220_0329
ProCarManuals.com
DYNOMITE -2009-

(#')
Status Log No.Detected Item Probable Cause
22-328Immobilizer System
Status Log
If you suspect there is a immobilizer system problem, check the status log in the HDS.
1. Connect the HDS to the data link connector.
2. Turn the ignition switch to ON (II).
3. On the HDS screen, at MAIN MENU, enter IMMOBILIZER, then select IMMOBILIZER SET-UP, select IMMOBILIZER INFORMATION, then select STATUS LOG.
4. Check the STATUS LOG count. Troubleshoot the status with the highest count first. If no counts are listed, the immobilizer system is OK. Continue with normal symptom troubleshooting.






































A-1 KEY CODE MISMATCH
(Code format normal, but code
data is mismatch) The key was not registered
Interference from metal such as key chains
Low battery voltage
A-2 KEY CODE MISMATCH (Code format failure) Ignition switch was turned to ON (II) with another type of immobilizer key or
aftermarket key
Interference from metal such as key chains
Low battery voltage
A-3 KEY CODE MISMATCH (No key code or non-
immobilizer key) Ignition switch was turned to ON (II) with another type of immobilizer key or
aftermarket key
Interference from metal such as key chains
Low battery voltage
Key failure
Immobilizer-keyless control unit failure
B-1 ECM/PCM CODE MISMATCH (Code format normal, but code
data is mismatch) ECM/PCM was not registered correctly
Low battery voltage
Poor or loose terminal connections at the immobilizer-keyless control unit
Communication line electrical noise
B-2 ECM/PCM MISMATCH (Code format failure) ECM/PCM was not registered correctly
Low battery voltage
Poor or loose terminal connections at the immobilizer-keyless control unit
Communication line electrical noise
C-1 IMOES UNIT mismatch (Code format normal, but data is
mismatch) Imoes unit was not registered
The communication was not good between imoes unit and immobilizer unit
by battery voltage low
The communication was not good between imoes unit and immobilizer unit
by influence of some noise
C-2 IMOES UNIT mismatch (Code format failure) Imoes unit was not registered correctly
The communication was not good between imoes unit and immobilizer unit
by battery voltage low
The communication was not good between imoes unit and immobilizer unit
by influence of some noise
D-1 SECURITY-NET LINE PROBLEM IMOCD (S-NET)
(Short to ground) Low battery voltage
Poor or loose terminal connections at the immobilizer-keyless control unit and
the ECM/PCM
Communication line electrical noise
D-2 SECURITY-NET LINE PROBLEM (No communication) Blown fuse
Harness open from imoes unit to immobilizer unit
The communication was not good between imoes unit and immobilizer unit
by battery voltage low
The communication was not good between imoes unit and immobilizer unit
by influence of some noise
Imoes unit failure
Immobilizer unit failure
D-3 SECURITY-NET LINE PROBLEM IMOCD (S-NET)
(Open line or ECM/PCM failure) Open or short in the harness from the ECM/PCM to the immobilizer-keyless
control unit
Low battery voltage
Poor or loose terminal connections at the immobilizer-keyless control unit and
the ECM/PCM
Communication line electrical noise
08/08/21 14:37:01 61SNR030_220_0330
ProCarManuals.com
DYNOMITE -2009-