2006 ACURA CSX engine



µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
21-61
ECM/PCM CONNECTOR A (44P)
GRY
JUMPER WIRE A/C DIODE B 2P SOCKET
A/C DIODE B
1 2
1 2
8. Turn the ignition switch to LOCK (0).
9. Reinstall the A/C condenser fan relay.
10. Jump the SCS line with the HDS. NOTE: This step must be done to protect the engine
control module (ECM)/powertrain control module
(PCM) from damage.
11. Disconnect ECM/PCM connector A (44P).
12. Connect the ECM/PCM connector A (44P) terminal No. 5 to body ground with a jumper wire.
13. Turn the ignition switch to ON (II). Check for loose wires or poor connections at
ECM/PCM connector A (44P) terminal No. 5. If the
connections are good, substitute a known-good
ECM/PCM, and recheck. If the symptom/indication
goes away, replace the original ECM/PCM
(see page 11-228).
Repair open in the wire between the A/C
condenser fan relay and the ECM/PCM. 14. Remove the A/C diode B from the under-hood fuse/
relay box.
15. Turn the ignition switch to ON (II).
16. Measure the voltage between the A/C diode B 2P socket terminal No. 2 and body ground.
Go to step 17.
Replace the under-hood fuse/relay box
(see page 22-65).
17. Using the diode setting ( ) on a DVOM, check for current flow in both directions between the A/C
diode B terminals No. 1 and No. 2.
Replace the under-hood fuse/relay box
(see page 22-65).
Replace the A/C diode B.
Terminal side of female terminals
Does t he A/ C cond enser f an r un on hi gh? Is there battery voltage?
I s t her e cur r ent f l ow i n onl y one d i r ect i on?
08/08/21 14:43:32 61SNR030_210_0062
ProCarManuals.com
DYNOMITE -2009-

µµµµ

(#'





)
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
21-62
Climate Control
A/C Compressor Clutch Circuit Troubleshooting
A/C COMPRESSOR CLUTCH RELAY 4P SOCKET
NOTE:
 It is normal for the A/C compressor to turn off under certain conditions, such as low idle, high engine
coolant temperature, or hard acceleration.
 Do not use this troubleshooting procedure if the fans are also inoperative with the A/C on. Refer to the
symptom troubleshooting index.
 Before doing any symptom troubleshooting, check for powertrain DTCs (see page 11-3).
1. Check the No. 20 (7.5 A) fuse in the under-hood fuse/relay box, and the No. 36 (10 A) fuse in the
under-dash fuse/relay box.
Go to step 2.
Replace the fuses and recheck. If the fuses
blow again, check for a short in the No. 20 (7.5 A)
and No. 36 (10 A) fuses circuit.
2. Connect the HDS to the DLC.
3. Start the engine.
4. Turn on the A/C.
5. Using the HDS, confirm the following values in the PGM-FI Data List at idle.
ECT Sensor 2 80 100 °C (176 212 °F)
TP Sensor About 0.5 V at idle
RPM More than 670
A/C Switch ON
A/C Clutch ON
A/C Pressure
Sensor 196 455 kPa (28 455 psi)
Go to step 6.
Troubleshoot the value that is not within the
specifications. 6. Turn the ignition switch to LOCK (0).
7. Remove the A/C compressor clutch relay from the
under-hood fuse/relay box, and test it (see page
22-70).
Go to step 8.
Replace the A/C compressor clutch relay.
8. Measure the voltage between the A/C compressor clutch relay 4P socket terminal No. 1 and body
ground.
Go to step 9.
Replace the under-hood fuse/relay box
(see page 22-65).
Ar e t he f uses OK ?
Are all the values within specif ications? Is the relay OK ?
Is there battery voltage?
08/08/21 14:43:32 61SNR030_210_0063
ProCarManuals.com
DYNOMITE -2009-


Î
µ
µ
µ
µ µ
µ
YES
NO
YES
NO
YES
NO
21-63
JUMPER WIRE
PUR
A/C COMPRESSOR CLUTCH RELAY 4P SOCKET
A/C COMPRESSOR CLUTCH RELAY 4P SOCKET
BRN ECM/PCM CONNECTOR A (44P)
JUMPER WIRE RED
9. Connect the A/C compressor clutch relay 4P socket
terminals No. 1 and No. 2 with a jumper wire.
Go to step 10.
Go to step 19.
10. Disconnect the jumper wire.
11. Turn the ignition switch to ON (II).
12. Measure the voltage between the A/C compressor clutch relay 4P socket terminal No. 3 and body
ground.
Go to step 13.
Repair open in the wire between the No. 36
(10 A) fuse in the under-dash fuse/relay box and the
A/C compressor clutch relay. 13. Turn the ignition switch to LOCK (0).
14. Reinstall the A/C compressor clutch relay.
15. Jump the SCS line with the HDS.
NOTE: This step must be done to protect the engine
control module (ECM)/powertrain control module
(PCM) from damage.
16. Disconnect ECM/PCM connector A (44P).
17. Connect the ECM/PCM connector A (44P) terminal No. 14 to body ground with a jumper wire.
18. Turn the ignition switch to ON (II). Check for loose wires or poor connections at
ECM/PCM connector A (44P). If the connections are
good, check the ECM/PCM grounds. If the grounds
are good, substitute a known-good ECM/PCM, and
recheck. If the symptom/indication goes away,
replace the original ECM/PCM (see page 11-228).
Repair open in the wire between the A/C
compressor clutch relay and the ECM/PCM.
(cont’d)
Terminal side of female terminals
Does the A/ C compressor clutch click?
Is there battery voltage? Does t he A/ C compr essor cl i ck ?
08/08/21 14:43:33 61SNR030_210_0064
ProCarManuals.com
DYNOMITE -2009-



(#'



)
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
21-6421-64Climate Control
A/C Compressor Clutch Circuit
Troubleshooting (cont’d)
A/C Signal Circuit Troubleshooting
A/C COMPRESSOR CLUTCH RELAY 4P SOCKET
RED/WHT
A/C COMPRESSOR CLUTCH 3P CONNECTOR PUR
REDBRN
CLIMATE CONTROL UNIT 32P CONNECTOR
19. Disconnect the jumper wire.
20. Disconnect the A/C compressor clutch 3P connector.
21. Check for continuity between the A/C compressor
clutch relay 4P socket terminal No. 2 and the A/C
compressor clutch 3P connector terminal No. 2.
Check the A/C compressor clutch clearance,
and the compressor clutch field coil (see page
21-85). Repair as needed.
Repair open in the wire between the A/C
compressor clutch relay and the A/C compressor
clutch. NOTE:
 Do not use this troubleshooting procedure if any of the following items are operative: A/C condenser fan,
radiator fan, A/C compressor. Refer to the symptom
troubleshooting index.
 Before doing symptom troubleshooting, check for powertrain DTCs (see page 11-3).
1. Connect the HDS to the DLC.
2. Start the engine.
3. Turn on the A/C.
4. Check the A/C SWITCH in the PGM-FI Data List with the HDS.
The A/C signal is OK at this time.
Go to step 5.
5. Turn the ignition switch to LOCK (0), and disconnect the climate control unit 32P connector.
6. Measure the evaporator temperature sensor resistance between the climate control unit 32P
connector terminals No. 8 and No. 19.
Go to step 7.
Test the evaporator temperature sensor
(see page 21-70).
Wire side of female terminals
Wire side of female terminals
Is there continuity?Is the A/ C SW IT CH on?
I s r esi st ance l ess t han 24 k ?
08/08/21 14:43:33 61SNR030_210_0065
ProCarManuals.com
DYNOMITE -2009-



(#'



)
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
21-6421-64Climate Control
A/C Compressor Clutch Circuit
Troubleshooting (cont’d)
A/C Signal Circuit Troubleshooting
A/C COMPRESSOR CLUTCH RELAY 4P SOCKET
RED/WHT
A/C COMPRESSOR CLUTCH 3P CONNECTOR PUR
REDBRN
CLIMATE CONTROL UNIT 32P CONNECTOR
19. Disconnect the jumper wire.
20. Disconnect the A/C compressor clutch 3P connector.
21. Check for continuity between the A/C compressor
clutch relay 4P socket terminal No. 2 and the A/C
compressor clutch 3P connector terminal No. 2.
Check the A/C compressor clutch clearance,
and the compressor clutch field coil (see page
21-85). Repair as needed.
Repair open in the wire between the A/C
compressor clutch relay and the A/C compressor
clutch. NOTE:
 Do not use this troubleshooting procedure if any of the following items are operative: A/C condenser fan,
radiator fan, A/C compressor. Refer to the symptom
troubleshooting index.
 Before doing symptom troubleshooting, check for powertrain DTCs (see page 11-3).
1. Connect the HDS to the DLC.
2. Start the engine.
3. Turn on the A/C.
4. Check the A/C SWITCH in the PGM-FI Data List with the HDS.
The A/C signal is OK at this time.
Go to step 5.
5. Turn the ignition switch to LOCK (0), and disconnect the climate control unit 32P connector.
6. Measure the evaporator temperature sensor resistance between the climate control unit 32P
connector terminals No. 8 and No. 19.
Go to step 7.
Test the evaporator temperature sensor
(see page 21-70).
Wire side of female terminals
Wire side of female terminals
Is there continuity?Is the A/ C SW IT CH on?
I s r esi st ance l ess t han 24 k ?
08/08/21 14:43:33 61SNR030_210_0065
ProCarManuals.com
DYNOMITE -2009-




(#'


 )
21-81
Heater Unit/Core Replacement
A
B C
8x1.25mm
12.3 N·m
(1.3 kgf·m, 9.0 lbf·ft)
B A
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
1. Do the battery terminal disconnection procedure (see page 22-68).
2. Disconnect the A/C line from the evaporator core
(see page 21-78).
3. Remove the air cleaner housing assembly (see page 11-345).
4. When the engine is cool, drain the engine coolant from the radiator (see page 10-8).
5. From under the hood, slide the hose clamps (A) back. Disconnect the inlet heater hose (B) and the
outlet heater hose (C) from the heater unit. Note the
orientation of the hoses.
Engine coolant will run out when the hoses are
disconnected; drain it into a clean drip pan. Be sure
not to let coolant spill on the electrical parts or the
painted surfaces. If any coolant spills, rinse it off
immediately. 6. Remove the mounting nut from the heater unit.
Take care not to damage or bend the fuel lines or
brake lines, etc.
7. Remove the dashboard (see page 20- 108).
8. Disconnect the connector (A) from the blower motor. Remove the wire harness clip (B).
(cont’d)
08/08/21 14:43:43 61SNR030_210_0082
ProCarManuals.com
DYNOMITE -2009-


(#'



 )
21-8321-83
A/C Compressor Replacement
A C
B
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
B
13. Remove the self-tapping screws, the heater core cover (A), the grommet (B). and carefully pull out
the heater core (C).
14. Install the heater core and the evaporator core in the reverse order of removal.
15. Install the heater unit in the reverse order of removal, and note these items:
 Do not interchange the inlet and outlet heater hoses, and install the hose clamps securely.
 Refill the cooling system with engine coolant (see page 10-8).
 Make sure that there is no coolant leakage.
 Make sure that there is no air leakage.
 Refer to evaporator core replacement (see page 21-78).
16. Do the battery terminal reconnection procedure (see page 22-68). NOTE: Do not install an A/C compressor into a system
unless you are completely sure that the system is free
of contamination. Installing the A/C compressor into a
contaminated system can result in premature A/C
compressor failure.
1. If the A/C compressor is marginally operable, run the engine at idle speed, and let the air
conditioning work for a few minutes, then shut the
engine off.
2. Recover the refrigerant with a recovery/recycling/ charging station (see page 21-90).
3. Remove the drive belt (see page 4-31).
4. Remove the front bulkhead and the condenser fan shroud (see page 10-19).
5. Remove the splash shield (see page 20-172).
6. Remove the bolt and the nut, then disconnect the suction hose (A) and discharge hose (B) from the
A/C compressor. Plug or cap the lines immediately
after disconnecting them to avoid moisture and
dust contamination.
(cont’d)
08/08/21 14:43:45 61SNR030_210_0084
ProCarManuals.com
DYNOMITE -2009-


(#'



 )
21-8321-83
A/C Compressor Replacement
A C
B
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
B
13. Remove the self-tapping screws, the heater core cover (A), the grommet (B). and carefully pull out
the heater core (C).
14. Install the heater core and the evaporator core in the reverse order of removal.
15. Install the heater unit in the reverse order of removal, and note these items:
 Do not interchange the inlet and outlet heater hoses, and install the hose clamps securely.
 Refill the cooling system with engine coolant (see page 10-8).
 Make sure that there is no coolant leakage.
 Make sure that there is no air leakage.
 Refer to evaporator core replacement (see page 21-78).
16. Do the battery terminal reconnection procedure (see page 22-68). NOTE: Do not install an A/C compressor into a system
unless you are completely sure that the system is free
of contamination. Installing the A/C compressor into a
contaminated system can result in premature A/C
compressor failure.
1. If the A/C compressor is marginally operable, run the engine at idle speed, and let the air
conditioning work for a few minutes, then shut the
engine off.
2. Recover the refrigerant with a recovery/recycling/ charging station (see page 21-90).
3. Remove the drive belt (see page 4-31).
4. Remove the front bulkhead and the condenser fan shroud (see page 10-19).
5. Remove the splash shield (see page 20-172).
6. Remove the bolt and the nut, then disconnect the suction hose (A) and discharge hose (B) from the
A/C compressor. Plug or cap the lines immediately
after disconnecting them to avoid moisture and
dust contamination.
(cont’d)
08/08/21 14:43:45 61SNR030_210_0084
ProCarManuals.com
DYNOMITE -2009-