µ
µ
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
14-121
6. Measure the 1st clutch pressure (see page 14-211).
Go to step 7.
Shift valves B and C are stuck. Repair these
valves and the hydraulic circuit, or replace the
transmission, then go to step 12.
7. Turn the ignition switch to ON (II).
8. Clear the DTC with the HDS.
9. Test-drive the vehicle in 1st gear, with the shift lever in D, at speeds over 12 km/h (7 mph), and
with the engine speed above 1,000 rpm, for at least
12 seconds.
10. Check for Temporary DTCs or DTCs with the HDS.
Repair the 1st clutch, or replace the
transmission, then go to step 12.
Go to step 11.
11. Monitor the OBD STATUS for P0731 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 10,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, repair the 1st
clutch, or replace the transmission, then go to step
12. If the HDS indicates NOT COMPLETED, go to
step 9. 12. Test-drive the vehicle in 1st gear, with the shift
lever in D, at speeds over 12 km/h (7 mph), and
with the engine speed above 1,000 rpm, for at least
12 seconds.
13. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the input shaft (mainshaft)
speed sensor and the output shaft (countershaft)
speed sensor and the PCM, then go to step 4.
Go to step 14.
14. Monitor the OBD STATUS for P0731 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 13,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the input
shaft (mainshaft) speed sensor and the output shaft
(countershaft) speed sensor and the PCM, then go
to step 4. If the HDS indicates NOT COMPLETED, go
to step 12.
Is the 1st clutch pressure within the service limits?
Is DT C P07 31 ind icated ?Does the HDS ind icate PASSED? Is DT C P07 31 ind icated ?
Does the HDS ind icate PASSED?
08/08/21 14:42:30 61SNR030_140_0123
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
DTC P0733:
14-12314-123
12. Test-drive the vehicle in 2nd gear, with the shift
lever in D, at speeds over 12 km/h (7 mph), and
with the engine speed above 1,000 rpm, for at least
12 seconds.
13. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the input shaft (mainshaft)
speed sensor and the output shaft (countershaft)
speed sensor and the PCM, then go to step 4.
Go to step 14.
14. Monitor the OBD STATUS for P0732 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 13,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the input
shaft (mainshaft) speed sensor and the output shaft
(countershaft) speed sensor and the PCM, then go
to step 4. If the HDS indicates NOT COMPLETED, go
to step 12. NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 11.
Replace the ATF (see page 14-232), then go to
step 4.
4. Measure the line pressure (see page 14-211).
Go to step 5.
Repair the ATF pump and the regulator valve,
or replace the transmission, then go to step 11.
5. Measure the 3rd clutch pressure (see page 14-211).
Go to step 6.
Shift valves A and D are stuck. Repair these
valves and the hydraulic circuit, or replace the
transmission, then go to step 11.
(cont’d)Problem in 3rd Clutch and 3rd
Clutch Hydraulic Circuit (3rd Gear Incorrect
Ratio)
Is DT C P07 32 ind icated ?
Does the HDS ind icate PASSED? Does t he st r ai ner hav e met al d ebr i s or ex cessi v e
clutch mater ial?
Is the line pressure within the service limits?Is the 3rd clutch pressure within the servicelimits?
08/08/21 14:42:30 61SNR030_140_0125
ProCarManuals.com
DYNOMITE -2009-
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-124Automatic Transmission
DTC Troubleshooting (cont’d)
6. Turn the ignition switch to ON (II).
7. Clear the DTC with the HDS.
8. Test-drive the vehicle in 3rd gear, with the shift
lever in D, at speeds over 12 km/h (7 mph), and
with the engine speed above 1,000 rpm, for at least
12 seconds.
9. Check for Temporary DTCs or DTCs with the HDS.
Repair the 3rd clutch, or replace the
transmission, then go to step 11.
Go to step 10.
10. Monitor the OBD STATUS for P0733 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 9,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, repair the 3rd
clutch, or replace the transmission, then go to step
11. If the HDS indicates NOT COMPLETED, go to
step 8. 11. Test-drive the vehicle in 3rd gear, with the shift
lever in D, at speeds over 12 km/h (7 mph), and
with the engine speed above 1,000 rpm, for at least
12 seconds.
12. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the input shaft (mainshaft)
speed sensor and the output shaft (countershaft)
speed sensor and the PCM, then go to step 4.
Go to step 13.
13. Monitor the OBD STATUS for P0733 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 12,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the input
shaft (mainshaft) speed sensor and the output shaft
(countershaft) speed sensor and the PCM, then go
to step 4. If the HDS indicates NOT COMPLETED, go
to step 11.
Is DT C P07 33 ind icated ?
Does the HDS ind icate PASSED? Is DT C P07 33 ind icated ?
Does the HDS ind icate PASSED?
08/08/21 14:42:31 61SNR030_140_0126
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
DTC P0735:
14-12614-126Automatic Transmission
DTC Troubleshooting (cont’d)
11. Test-drive the vehicle in 4th gear, with the shift
lever in D, at speeds over 12 km/h (7 mph), and
with the engine speed above 1,000 rpm, for at least
12 seconds.
12. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the input shaft (mainshaft)
speed sensor and the output shaft (countershaft)
speed sensor and the PCM, then go to step 4.
Go to step 13.
13. Monitor the OBD STATUS for P0734 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 12,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the input
shaft (mainshaft) speed sensor and the output shaft
(countershaft) speed sensor and the PCM, then go
to step 4. If the HDS indicates NOT COMPLETED, go
to step 11. NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 11.
Replace the ATF (see page 14-232), then go to
step 4.
4. Measure the line pressure (see page 14-211).
Go to step 5.
Repair the ATF pump and the regulator valve,
or replace the transmission, then go to step 11.
5. Measure the 5th clutch pressure (see page 14-211).
Go to step 6.
Shift valves A, B, and/or D are stuck. Repair
these valves and the hydraulic circuit, or replace
the transmission, then go to step 11.Problem in 5th Clutch and 5th
Clutch Hydraulic Circuit (5th Gear Incorrect
Ratio)
Is DT C P07 34 ind icated ?
Does the HDS ind icate PASSED? Does t he st r ai ner hav e met al d ebr i s or ex cessi v e
clutch mater ial?
Is the line pressure within the service limits?Is the 5th clutch pressure within the servicelimits?
08/08/21 14:42:31 61SNR030_140_0128
ProCarManuals.com
DYNOMITE -2009-
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-127
6. Turn the ignition switch to ON (II).
7. Clear the DTC with the HDS.
8. Test-drive the vehicle in 5th gear, with the shift
lever in D, at speeds over 12 km/h (7 mph), and
with the engine speed above 1,000 rpm, for at least
12 seconds.
9. Check for Temporary DTCs or DTCs with the HDS.
Repair the 5th clutch, or replace the
transmission, then go to step 11.
Go to step 10.
10. Monitor the OBD STATUS for P0735 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 9,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, repair the 5th
clutch, or replace the transmission, then go to step
11. If the HDS indicates NOT COMPLETED, go to
step 8. 11. Test-drive the vehicle in 5th gear, with the shift
lever in D, at speeds over 12 km/h (7 mph), and
with the engine speed above 1,000 rpm, for at least
12 seconds.
12. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the input shaft (mainshaft)
speed sensor and the output shaft (countershaft)
speed sensor and the PCM, then go to step 4.
Go to step 13.
13. Monitor the OBD STATUS for P0735 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 12,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the input
shaft (mainshaft) speed sensor and the output shaft
(countershaft) speed sensor and the PCM, then go
to step 4. If the HDS indicates NOT COMPLETED, go
to step 11.
Is DT C P07 35 ind icated ?
Does the HDS ind icate PASSED? Is DT C P07 35 ind icated ?
Does the HDS ind icate PASSED?
08/08/21 14:42:31 61SNR030_140_0129
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
DTC P0741:
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
14-128
Automatic Transmission
DTC Troubleshooting (cont’d)
Torque Converter Clutch
Hydraulic Circuit Stuck OFF
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 13.
Replace the ATF (see page 14-232), then go to
step 4.
4. Turn the ignition switch to ON (II).
5. Clear the DTC with the HDS.
6. Select Shift Solenoid Valve E in the Miscellaneous Test Menu, and check that shift solenoid valve E
operates with the HDS.
Go to step 7.
Replace shift solenoid valve E (see page
14-217), then go to step 11.
7. Run the engine until the ECT Sensor temperature reaches 80 °C (176 °F).
8. Select Clutch Pressure Control (Linear) Solenoid Valve A in the Miscellaneous Test Menu, and test
A/T clutch pressure control solenoid valve A with
the HDS.
Go to step 9.
Follow the instructions indicated on the HDS
accordingtothetestresult.Gotostep11ifanypart
was replaced. 9. Test-drive the vehicle on a level road with a steady
speed at 96 km/h (60 mph) for at least 20 seconds.
10. Monitor the OBD STATUS for P0741 in the DTCs MENU with the HDS.
Repair the faulty torque converter clutch
mechanism, the torque converter clutch hydraulic
circuit, the lock-up shift valve, or the lock-up control
valve, or replace the transmission, then go to step
13.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, go to step 9.
11. Turn the ignition switch to ON (II).
12. Clear the DTC with the HDS.
13. Test-drive the vehicle on a level road with a steady speed at 96 km/h (60 mph) for at least 20 seconds,
or test-drive the vehicle for several minutes under
the same condition as those indicated by the freeze
data.
14. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Go to step 15.
15. Monitor the OBD STATUS for P0741 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 14,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, go to step 5. If
the HDS indicates NOT COMPLETED, go to step 13.
Does t he st r ai ner hav e met al d ebr i s or ex cessi v e clutch mater ial?
Is a clicking sound heard?Does the HDS ind icate NORMAL? Does the HDS ind icate F AILED?
Is DTC P0741 indicated?Does the HDS ind icate PASSED?
08/08/21 14:42:31 61SNR030_140_0130
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ
µ
µ µ
µ
DTC P2122:
YES
NO
YES
NO
YES
NO YES
NO
14-203
Accelerator Pedal Position (APP)
Sensor A (Throttle Position Sensor D) Circuit
Low Voltage Input
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Check for Temporary DTCs or DTCs in the PGM-FI SYSTEM with the HDS.
Go to the DTC P2122 troubleshooting in the
electronic throttle control system (ETCS) (see page
11-253).
Go to step 4.
4. Check for Temporary DTCs or DTCs in the A/T SYSTEM with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. If any other Temporary DTCs or DTCs were
indicated, go to the indicated DTC’s
troubleshooting.
5. Update the PCM if it does not have the latest software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
6. Start the engine, and wait for at least 2 minutes.
7. Check for Temporary DTCs or DTCs in the A/T SYSTEM with the HDS.
Check for poor connections or loose
terminals at the PCM. If the PCM was updated,
substitute a known-good PCM (see page 11-7), then
go to step 6. If the PCM was substituted, go to step
1.
Go to step 8. 8. Monitor the OBD STATUS for P2122 in the DTCs
MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 7,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals at the PCM. If the
PCM was updated, substitute a known-good PCM
(see page 11-7), then go to step 6. If the PCM was
substituted, go to step 1. If the HDS indicates NOT
COMPLETED, go to step 6.
Is DT C P2122 indicated in the PGM-F I SY ST EM?
Is DT C P2122 indicated in the A/ T SY ST EM?
Is DT C P2122 indicated in the A/ T SY ST EM? Does the HDS ind icate PASSED?
08/08/21 14:45:31 61SNR030_140_0205
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ
µ
µ µ
µ
DTC P2123:
YES
NO
YES
NO
YES
NO YES
NO
14-204
Automatic Transmission
DTC Troubleshooting (cont’d)
Accelerator Pedal Position (APP)
Sensor A (Throttle Position Sensor D) Circuit
High Voltage Input
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Check for Temporary DTCs or DTCs in the PGM-FI SYSTEM with the HDS.
Go to the DTC P2123 troubleshooting in the
electronic throttle control system (ETCS) (see page
11-256).
Go to step 4.
4. Check for Temporary DTCs or DTCs in the A/T SYSTEM with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. If any other Temporary DTCs or DTCs were
indicated, go to the indicated DTC’s
troubleshooting.
5. Update the PCM if it does not have the latest software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
6. Start the engine, and wait for at least 2 minutes.
7. Check for Temporary DTCs or DTCs in the A/T SYSTEM with the HDS.
Check for poor connections or loose
terminals at the PCM. If the PCM was updated,
substitute a known-good PCM (see page 11-7), then
go to step 6. If the PCM was substituted, go to step
1.
Go to step 8. 8. Monitor the OBD STATUS for P2123 in the DTCs
MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 7,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals at the PCM. If the
PCM was updated, substitute a known-good PCM
(see page 11-7), then go to step 6. If the PCM was
substituted, go to step 1. If the HDS indicates NOT
COMPLETED, go to step 6.
Is DT C P2123 indicated in the PGM-F I SY ST EM?
Is DT C P2123 indicated in the A/ T SY ST EM?
Is DT C P2123 indicated in the A/ T SY ST EM? Does the HDS ind icate PASSED?
08/08/21 14:45:31 61SNR030_140_0206
ProCarManuals.com
DYNOMITE -2009-