2006 ACURA CSX door lock



(#'



 )
20-1920-19
Rear Door Outer Handle
Replacement
A B
62 mm (2.44 in.) A
B
C
D C
A
10. Install the door panel in the r everse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Replace any damaged cable fasteners with new ones.
 The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
 Make sure the connector is plugged in properly, and the cables are connected securely.
 Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Detach the harness clip (A), and disconnect the power door lock actuator connector (B).
4. Remove the plug caps (C), then remove the plastic cover (D), as needed.
5. Remove the latch mounting screws, then lower the latch (see step 4 on page 20-21).
6. Detach the rod fastener (A).
(cont’d)
08/08/21 14:59:06 61SNR030_200_0021
ProCarManuals.com
DYNOMITE -2009-



(#'



 )
20-1920-19
Rear Door Outer Handle
Replacement
A B
62 mm (2.44 in.) A
B
C
D C
A
10. Install the door panel in the r everse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Replace any damaged cable fasteners with new ones.
 The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
 Make sure the connector is plugged in properly, and the cables are connected securely.
 Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Detach the harness clip (A), and disconnect the power door lock actuator connector (B).
4. Remove the plug caps (C), then remove the plastic cover (D), as needed.
5. Remove the latch mounting screws, then lower the latch (see step 4 on page 20-21).
6. Detach the rod fastener (A).
(cont’d)
08/08/21 14:59:06 61SNR030_200_0021
ProCarManuals.com
DYNOMITE -2009-


(#'


 )
20-2120-21
Rear Door Latch Replacement
Fastener Locations :Screw,3
A:Screw,1 B
A
A
A
6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft) 6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft)C
B
11. Install the handle in the reverse order of removal, and note these items:
 Make sure the door locks and opens properly.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29). NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Remove the plastic cover, as needed (see step 4 on page 20-19).
4. Remove the screws (A, B) securing the latch (C), then lower it.
5. Detach the rod fastener (see step 6 on page 20-19).
6. Disconnect the outer handle rod from the outer handle (see step 7 on page 20-20).
(cont’d)
08/08/21 14:59:07 61SNR030_200_0023
ProCarManuals.com
DYNOMITE -2009-


(#'


 )
20-2120-21
Rear Door Latch Replacement
Fastener Locations :Screw,3
A:Screw,1 B
A
A
A
6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft) 6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft)C
B
11. Install the handle in the reverse order of removal, and note these items:
 Make sure the door locks and opens properly.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29). NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Remove the plastic cover, as needed (see step 4 on page 20-19).
4. Remove the screws (A, B) securing the latch (C), then lower it.
5. Detach the rod fastener (see step 6 on page 20-19).
6. Disconnect the outer handle rod from the outer handle (see step 7 on page 20-20).
(cont’d)
08/08/21 14:59:07 61SNR030_200_0023
ProCarManuals.com
DYNOMITE -2009-



20-22Doors
Rear Door Latch Replacement (cont’d)
A
B
C
D F
E
Fastener Location :Screw,1
AB A
A
B
C
B
7. Detach the latch cable (A) and the inner handlecable (B) from the holder (C), then remove the latch
(D) out from between the rear lower channel (E)
and the door. Take care not to bend the outer
handle rod (F), the latch cable, or the inner handle
cable.
8. Remove the screw, then remove the latch protector (A) by releasing the hook (B). 9. Detach the latch cable (A) and the inner handle
cable (B) from the latch (C).
10. Install the latch in the reverse order of removal, and note these items:
 Make sure the connector is plugged in properly, and each rod is connected securely.
 Make sure the door locks and opens properly.
08/08/21 14:59:07 61SNR030_200_0024
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
20-23
Rear Door Glass and Regulator Replacement
A
B C
FG
H
E
C
E
D
Fastener Locations :Bolt,2
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)A
B
A
C Fastener Locations
:Bolt,1
A:Screw,1 D
4x0.7mm
4N·m
(0.4 kgf·m, 3 lbf·ft)
6x1.0mm
8N·m
(0.8 kgf·m, 6 lbf·ft) A
B C
D
NOTE: Put on gloves to protect your hands.
1. Remove the door panel (see page 20-17).
2. Detach the harness clip (A), and disconnect the power door lock actuator connector (B). Remove
the plug caps (C).
3. Pass the cable (D) and the harnesses (E) through the holes (F) and slit (G) in the plastic cover (H),
then remove it.
4. Carefully move the glass (A) until you can see the bolts, then remove them. Release the glass from
the holder (B), then remove it from the regulator (C),
and carefully lower the glass. Take care not to drop
the glass inside the door. 5. Remove the bolt (A) from the rear lower channel (B).
Pull the glass run channel (C) away as needed, and
remove the screw (D).
(cont’d)
08/08/21 14:59:08 61SNR030_200_0025
ProCarManuals.com
DYNOMITE -2009-


(#'


 )
20-27
Rear Door Weatherstrip Replacement
Fastener Locations:Bolt,1
A :Clip,13
B
B A B
C
D F
E C
E
E
E
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft) : Clip, 2
C
:Clip,1
D (White)
(Black) (Left: Yellow
Right: Green)
NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the door.
 Remove the clips with a clip remover.
1. At the B-pillar, remove the door checker mounting
bolt (A).
2. Detach the clips (B, C, D), then remove the door weatherstrip (E). 3. Install the weatherstrip in the reverse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Make sure the weatherstrip is installed in the holder (F) securely.
 Apply medium strength liquid thread lock to the door checker mounting bolt before installation.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:10 61SNR030_200_0029
ProCarManuals.com
DYNOMITE -2009-



(#' )

S

pecial Tools Required
Driver’s side Passenger’s sideFront Door Sill Area
20-66Interior Trim
Trim Removal/Installation - Door Areas
A
B C
D
E
F
G G
A B A
B
G
G
Fastener Locations
:Clip,1
F : Clip, 4
G
(White)
(Orange)
E Fa
stener Locations
: Clip, 1
F : Clip, 4
G
(White)
(Orange)
A
B
C D E
F
G B
A
A
BG
G
G
E
AB
A
A
KTC trim tool set SOJATP2014
NOTE:
Put on gloves to protect your hands.
 Take care not to bend or scratch the trim and panels.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Driver’s side: Remove the footrest (see step 3 on page 20-89).
2. Driver’s side: Remove the front side cap from the front door sill trim, and remove the trunk lid/fuel fill
door opener lock cylinder and the screw (see page
20-184).
3. Detach the hooks (A) and the tabs (B) from the kick panel (C) and the B-pillar lower trim (D), and pull
the front door sill trim (E) up by hand to detach the
clips (F, G), then remove it.
4

. Pull out the front door opening seal (A) from thetrim hooks (B) and around the front door opening
flange, then remove the seal.
08/08/21 15:01:29 61SNR030_200_0068
ProCarManuals.com
DYNOMITE -2009-