2006 ACURA CSX lock

(#'

)
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
11-204PGM-FI System
DLC Circuit Troubleshooting
NOTE: Make sure the HDS and the HDS DLC cable are
not detective.
1. Turn the ignition switch to LOCK (0).
2. Connect the HDS to the DLC (see page 11-3). NOTE: Make sure the HDS is properly connected to
the DLC.
3. Turn the ignition switch to ON (II), and read the HDS.
Go to step 4.
Go to step 25.
4. Check for Temporary DTCs or DTCs in the PGM-FI system with the HDS.
Go to the indicated DTC’s troubleshooting.
Go to step 5.
5. Turn the ignition switch to LOCK (0).
6. Turn the ignition switch to ON (II), and watch the SRS indicator.
Go to the SRS system’s general
troubleshooting information (see page 24-22).
 With ABS: Go to step 7.
 WithVSAsystem:Gotostep9. 7. Turn the ignition switch to LOCK (0).
8. Turn the ignition switch to ON (II), and watch the
ABS indicator.
Go to the ABS’s general troubleshooting
information (see page 19-49).
Go to step 11.
9. Turn the ignition switch to LOCK (0).
10. Turn the ignition switch to ON (II), and watch the VSA indicator.
Go to the VSA system’s general
troubleshooting information (see page 19-97).
Go to step 11.
11. Turn the ignition switch to LOCK (0).
12. Start the engine, and watch the EPS indicator.
Go to the EPS system’s general
troubleshooting information (see page 17-19).
Go to step 13.
Does the HDS identif y the vehicle?
Ar e any T empor ar y DT Cs or DT Cs i nd i cat ed ?
Does the SRS indicator stay on? Does the ABS indicator stay on?
Does the V SA indicator stay on?Does the EPS indicator stay on?
08/08/21 14:21:54 61SNR030_110_0204
ProCarManuals.com
DYNOMITE -2009-


µ
µ
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
11-205
DATA LINK CONNECTOR (DLC)
K-LINE (LT BLU)
13. Turn the ignition switch to LOCK (0).
14. Turn the ignition switch to ON (II), and watch theimmobilizer indicator.
Go to the immobilizer system’s
troubleshooting (see page 22- 315).
 With TPMS: Go to step 15.
 Without TPMS: Go to step 17.
15. Turn the ignition switch to LOCK (0).
16. Turn the ignition switch to ON (II), and watch the TPMS indicator.
Go to the TPMS’s general troubleshooting
information (see page 18-49).
Go to step 17.
17. Do the gauge self-diagnostic function (see page 22-241).
18. Check for B-CAN system DTCs without the HDS (see page 22-74).
Go to the indicated DTC’s troubleshooting.
Go to step 19.
19. Turn the ignition switch to LOCK (0).
20. Disconnect the HDS from the DLC. 21. Check for continuity between DLC terminal No. 7
and body ground.
Go to step 22.
Go to step 23.
22. Continue to check for continuity between DLC terminal No. 7 and body ground, while
disconnecting these parts, one at a time:
 SRS unit connector A (28P)
 ABS modulator-control unit 25P connector (with ABS)
 VSA modulator-control unit 37P connector (with VSA system)
 EPS control unit connector D (28P)
 Immobilizer-keyless control unit 7P c onnector
 TPMS control unit 20P connector (with TPMS)
 Audio unit 17P connector
 Under-dash fuse/relay box Q (16P) connector
Replace the part that caused an open when it
was disconnected.
Repair short in the wire between the DLC (K-
line) and the ABS modulator-control unit (with
ABS), the VSA modulator-control unit (with VSA
system), the SRS unit, the EPS control unit, the
immobilizer-keyless control unit, the audio unit, the
TPMS control unit (with TPMS), or the under-dash
fuse/relay box.
(cont’d)
Terminal side of female terminals
Does the immobilizer indicator stay on or f lash?
Does t he T PM S i nd i cat or st ay on?Ar e any B-CAN DT Cs i nd i cat ed ? Is there continuity?
Does cont i nui t y go aw ay w hen one of t he abov econnect or s i s d i sconnect ed ?
08/08/21 14:21:54 61SNR030_110_0205
ProCarManuals.com
DYNOMITE -2009-


´
µ
µ µ
µ
µ
µ
Connector Terminal
YES
NO YES
NO
YES
NO
11-206
PGM-FI System
DLC Circuit Troubleshooting (cont’d)
DATA LINK CONNECTOR (DLC)
K-LINE (LT BLU)
JUMPER WIRE
DATA LINK CONNECTOR (DLC)B(WHT)
23. Connect DLC terminal No. 7 to body ground with ajumper wire.
24. Check for continuity between body ground and these connector terminals:
SRS unit A (28P) No. 24 (LT BLU)
ABS modulator-control unit
25P (with ABS) No. 10
(LT BLU)
VSA modulator-control unit
37P (with VSA system) No. 26
(LTBLU)
EPS control unit D (28P) No. 17 (LT BLU)
Immobilizer-keyless control
unit 7P No. 5 (LT BLU)
TPMS control unit 20P No. 7 (LT BLU)
Audio unit 17P No. 6 (LT BLU)
Under-dash fuse/relay box Q
(16P) No. 8 (LT BLU)
Replace the part which cannot communicate
with the HDS.
Repair open in the wire between the DLC (K-
line) and the appropriate connector. 25. Do the gauge self-diagnostic function (see page
22-241).
26. Check for B-CAN system DTCs without the HDS (see page 22-74).
Go to step 39.
Go to step 27.
27. Turn the ignition switch to LOCK (0).
28. Disconnect the HDS from the DLC.
29. Measure the voltage between DLC terminal No. 16 and body ground.
Go to step 30.
Repair open in the wire between DLC terminal
No.16andtheNo.23BACKUP(10A)fuseinthe
under-hood fuse/relay box.
Terminal side of female terminals
Terminal side of female terminals
Is t her e cont i nui t y bet w een t he bod y gr ound andeach of t he t er mi nal s i n t he char t ? I s DT C B1168, B1169, and / or B117 8 i nd i cat ed ?
Is there battery voltage?
08/08/21 14:21:55 61SNR030_110_0206
ProCarManuals.com
DYNOMITE -2009-

µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-208PGM-FI System
DLC Circuit Troubleshooting (cont’d)
ECM/PCM CONNECTOR A (44P)
CANL (RED)
38. Check for continuity between ECM/PCM connectorterminal A37 and body ground.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Repair open in the wire between the ECM/
PCM (A37) and DLC terminal No. 14. 39. Try to start the engine.
Go to the F-CAN circuit troubleshooting
(see page 11-191).
Go to step 40.
40. Turn the ignition switch to LOCK (0).
41. Check the No. 2 IG MAIN (50 A) fuse in the under- hood fuse/relay box.
Repair open in the wire between the No. 2 IG
MAIN (50 A) fuse and the ignition switch. If the wire
isOK,gotostep42.
Repair short in the wire between the No. 2 IG
MAIN (50 A) fuse and the under-hood fuse/relay
box.AlsoreplacetheNo.2IGMAIN(50A)fuse.
Terminal side of female terminals
Is there continuity? Does t he engi ne st ar t and i d l e smoot hl y ?
IsthefuseOK?
08/08/21 14:21:56 61SNR030_110_0208
ProCarManuals.com
DYNOMITE -2009-


Î 

´
µ
µ µ
µ
YES
NO YES
NO
11-213
ECM/PCM CONNECTOR A (44P)
MRLY (GRN)
C B
PGM-FI MAIN RELAY 1 4P CONNECTOR
65. Measure the voltage between ECM/PCM connector
terminal A6 and body ground.
Go to step 70.
Go to step 66.
66. Turn the ignition switch to LOCK (0).
67. Remove PGM-FI main relay 1 (C) from the under- hood fuse/relay box. 68. Measure the voltage between PGM-FI main relay 1
4P connector terminal No. 3 and body ground.
Go to step 69.
Replace the under-hood fuse/relay box
(see page 22-65).
(cont’d)
Terminal side of female terminals Terminal side of female terminals
Is there battery voltage?
Is there battery voltage?
08/08/21 14:23:32 61SNR030_110_0213
ProCarManuals.com
DYNOMITE -2009-


Î


´
µ
µ
µ
µ
YES
NO
YES
NO
11-214PGM-FI System
DLC Circuit Troubleshooting (cont’d)
MRLY (GRN)
ECM/PCM
CONNECTOR A (44P) MRLY
PGM-FI MAIN RELAY 1 4P CONNECTOR
C
B
PGM-FI MAIN RELAY 1 4P CONNECTOR
69. Check for continuity between PGM-FI main relay 1
4P connector terminal No. 4 and ECM/PCM
connector terminal A6.
Test PGM-FI main relay 1 (see page 22-70). If
the relay is OK, update the ECM/PCM if it does not
have the latest software (see page 11-227), or
substitute a known-good ECM/PCM (see page 11-7),
then recheck. If the symptom/indication goes away
with a known-good ECM/PCM, replace the original
ECM/PCM (see page 11-228).
Repair open in the wire between the ECM/
PCM (A6) and PGM-FI main relay 1. 70. Turn the ignition switch to LOCK (0).
71. Remove PGM-FI main relay 1 (C) from the under-
hood fuse/relay box.
72. Measure the voltage between PGM-FI main relay 1 4P connector terminal No. 1 and body ground.
Go to step 73.
Replace the under-hood fuse/relay box
(see page 22-65).
Terminal side of female terminals
Terminal side of female terminals
Terminal side of female terminals
Is there continuity?Is there battery voltage?
08/08/21 14:23:32 61SNR030_110_0214
ProCarManuals.com
DYNOMITE -2009-

Ì
(#'
!)
Special Tools Required
11-227
ECM/PCM Update
A
 Honda diagnostic system (HDS) tablet tester
 Honda interface module (HIM) and an iN workstation
with the latest HDS software version
 HDS pocket tester
 GNA 600 and iN workstation with the latest HDS software version
Any one of the above updating tools can be used.
NOTE:  Make sure the HDS/iN workstation has the latest HDS software version.
 Before you update the ECM/PCM, make sure the battery in the vehicle is fully charged, and connect a
jumper battery (not a battery charger) to maintain
system voltage.
 Never turn the ignition switch to LOCK (0) or ACC (I) during the update. If there is a problem with the
update, l eave the ignition switch to ON (II).
 To prevent ECM/PCM damage, do not operate anything electrical (headlights, audio system, brakes,
A/C, power windows, moonroof (if equipped), door
locks, etc.) during the update.
 To ensure the latest program is installed, do an ECM/ PCM update when ever the ECM/PCM is substituted or
replaced.
 You cannot update an ECM/PCM with a program it already has. It will only accept a new program.
 High temperature in the engine compartment might cause the ECM/PCM to become too hot to run the
update. If the engine was running before this
procedure, open the hood, and cool the engine
compartment.
 If you need to diagnose the Honda interface module (HIM) because the HIM’s red ( 3) light came on or
was flashing during the update, l eave the ignition
switch in ON (II) when you disconnect the HIM from
the data link connector (DLC). This will pr event ECM/
PCM damage. 1. Turn the ignition switch to ON (II), but do not start
the engine.
2. Connect the HDS to the data link connector (DLC) (A) located under the driver’s side of the dashboard.
3. Make sure the HDS communicates with the ECM/ PCM. If it doesn’t, go to the DLC circuit
troubleshooting (see page 11-204). If you are
returning from the DLC circuit troubleshooting, skip
steps 4 to 5 and clean the throttle body after
updating the ECM/PCM (see page 11- 344).
4. Select the INSPECTION MENU with the HDS.
5. Select the ETCS TEST, then select the TP POSITION CHECK, and follow the HDS screen prompts.
NOTE: If the TP POSITION CHECK indicates FAILED,
continue this procedure.
6. Exit the HDS diagnostic system, then select the update mode, and follow the screen prompts to
update the ECM/PCM.
(cont’d)
08/08/21 14:23:39 61SNR030_110_0227
ProCarManuals.com
DYNOMITE -2009-

ØÚÓ

11-229
A
D
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
B
C
E
3. Make sure the HDS communicates with the ECM/ PCM and other vehicle systems. If it doesn’t, go to
the DLC circuit troubleshooting (see page 11-204). If
you are returning from DLC circuit troubleshooting,
skip steps 4 through 9, 20 through 25, and 28
through 30, and do these procedures after
replacing the ECM/PCM;
 Replace the engine oil (see page 8-10) and the engine oil filter (see page 8-11).
 Replace the ATF (A/T model) (see page 14-232).
 Clean the throttle body (see page 11- 344).
4. Select the PGM-FI system with the HDS.
5. Select the INSPECTION MENU with the HDS.
6. Select the ETCS TEST, then select the TP POSITION CHECK, and follow the screen prompts.
NOTE: If the TP POSITION CHECK indicates FAILED,
continue with this procedure.
7. Select the REPLACE ECM/PCM MENU, then select READ DATA, and follow the screen prompts.
NOTE: Doing this step copies (READS) the engine oil life data from the original ECM/PCM so you can later
download (WRITES) it into the new ECM/PCM.
 If READ DATA indicates FAILED, continue with this procedure.
8. A/T model: Select the A/T system with the HDS.
9. A/T model: Select the REPLACE TCM/PCM MENU, then select READ DATA and follow the screen
prompts.
NOTE: Doing this step copies (READS) the ATF life data from the original PCM so you can later download
(WRITES) it into the new PCM.
 If READ DATA indicates FAILED, continue with this procedure. 10. Turn the ignition switch to LOCK (0).
11. Jump the SCS line with the HDS.
12. Do the battery removal procedure (see page 22-69).
13. Remove the cover (A).
14. Remove the bolts (D), then remove the ECM/PCM
(E).
15. Disconnect ECM/PCM connectors A, B, and C. NOTE: ECM/PCM connectors A, B, and C have
symbols (A= , B= , C= ) embossed on them for
identification.
(cont’d)
08/08/21 14:23:40 61SNR030_110_0229
ProCarManuals.com
DYNOMITE -2009-