2006 ACURA CSX dashboard

Î
(#')
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
SRS indicator stays on, but no DTCs are
stored
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
24-182
SRS
Symptom Troubleshooting (cont’d)
SRS UNIT CONNECTOR A (28P)
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Connect the HDS to the data link connector (DLC) (see page 24-22).
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).
4. Select Body Electrical status with the HDS.
5. Check for DTCs in the Gauge Menu with the HDS.
Go to the troubleshooting for DTC B 1187
(see page 22-265).
Go to step 6.
6. Check that the HDS communicates with the SRS unit.
Go to step 7.
If the HDS does not communicate with the
SRS unit, check for power and ground at the SRS
unit connector A (28P). If power and grounds are ok,
replace the SRS unit (see page 24-203).
7. From the HDS System Menu, select SRS, then SRS in Mode Menu, PARAMETER INFORMATION, then
SCS, MES, Indicator. Read the current status of the
SRS indicator.
Faulty SRS unit; replace the SRS unit
(see page 24-203).
Go to step 8. 8. Do the gauge self-diagnostic test (see page 22-241).
Go to step 9.
Faulty gauge control module (tach); replace
the gauge control module (tach) (see page 22-277).
9. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, and wait at least 3
minutes.
10. Disconnect the SRS unit connector A (28P) from the SRS unit (see step 8 on page 24-21).
11. Measure the resistance between SRS unit connector A (28P) terminal No. 5 and body ground.
There should be an open circuit or at least 1 M .
Faulty SRS unit or poor connection at SRS
unit connector A (28P) and the SRS unit. Check the
connection between the connector and the SRS
unit. If the connection is OK, replace the SRS unit
(see page 24-203).
Short in the dashboard wire harness; replace
the dashboard wire harness.
Wire side of female terminals
I s DT C B1187 i nd i cat ed ?
Does the HDS communicate with the SRS unit?
Is the status ON? Does the SRS indicator f lash?
Is the resistance as specif ied?
08/08/21 14:01:53 61SNR030_240_0182
ProCarManuals.com
DYNOMITE -2009-




(#'
 )
Removal
24-189
Front Passenger’s Airbag Replacement
A A
B
CC
NOTE: If replacing the front passenger’s airbag after
deployment, refer to Component Replacement/
Inspection After Deployment (see page 24-185) for a
complete list of other parts that must also be replaced.1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the glove box (see page 20-104).
3. Disconnect the front passenger’s airbag 4P connector (A) from the dashboard wire harness.
4. Remove the center panel:  Navigation unit, with navigation system.– ’06-08 models (see page 23-256)
– ’09 model (see page 23-355)
 Audio unit, without navigation system. – ’06-08 models (see page 23-80)
– ’09 model (see page 23-155) 5. Remove the three mounting nuts (A) from the
bracket. Cover the front passenger’s lid and
dashboard with a cloth, and pry carefully with a
screwdriver to lift the front passenger’s airbag
assembly (B) out of the dashboard. If you replacing
only the front passenger’s lid, go to step 6.
NOTE: The front passenger’s lid has pawls (C) on
each side which attach it to the dashboard.
(cont’d)
08/08/21 14:01:55 61SNR030_240_0189
ProCarManuals.com
DYNOMITE -2009-




Installation
24-190SRS
Front Passenger’s Airbag Replacement (cont’d)
A
A
B
A
B B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
A
6. Cut the four parts (A) of the front passenger’s lid (B)as shown, and remove the front passenger’s airbag.
NOTE: Always replace the front passenger’s lid whenever you remove the front passenger’s
airbag from the lid.
 Replace the front passenger’s airbag if the airbag mounting hooks or its housing is damaged.
7. Insert the hooks (A) of the front passenger’s airbag housing into the new front passenger’s lid, then
insert the other hooks (B) into the lid.
NOTE: Make sure there are no objects between the airbag and the front passenger’s lid.
 Make sure the airbag is fully seated, and make sure the front passenger’s lid is not deformed or
damaged after the airbag is in place.
 Do not use tools when detaching the front passenger’s airbag in order to protect it. 1. Place the front passenger’s airbag assembly (A)
into the dashboard. Tighten the front passenger’s
airbag mounting nuts (B).
2. Connect the front passenger’s airbag 4P connector (A) to dashboard wire harness, then reinstall the
glove box and center panel.
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Clear any DTC (see page 24-23).
5. After installing the airbag, confirm proper system operation: Turn the ignition switch to ON (II); the
SRS indicator should come on for about 6 seconds
andthengooff.
08/08/21 14:01:56 61SNR030_240_0190
ProCarManuals.com
DYNOMITE -2009-

Î


Î
(#'
!)
Special Tools Required
Driver’s Airbag
Front Passenger’s Airbag
Side Airbag
Side Curtain Airbag
Deploying Airbags in the Vehicle
24-196
SRS
Airbag and Tensioner Disposal
A
B
A
A
A
Deployment tool 07HAZ-SG00500
Before scrapping any airbags, side airbags, side curtain
airbags, seat belt tensioners, or seat belt buckle
tensioner (including those in a whole vehicle to be
scrapped), the part(s) must be deployed. If the vehicle is
still within the warranty period, the Honda District Parts
and Service Manager must give approval and/or special
instructions before deploying the part(s). Only after the
part(s) have been deployed (as the result of vehicle
collision, for example), can they be scrapped.
If the parts appear intact (not deployed), treat them with
extreme caution. Follow this procedure.
If an SRS equipped vehicle is to be entirely scrapped, its
airbags, side airbags, side curtain airbags, seat belt
tensioners, and seat belt buckle tensioner should be
deployed while still in the vehicle. These parts should
not be considered as salvageable parts and should
never be installed in another vehicle.1. Turn the ignition switch to LOCK (0), then disconnect the negative cable from the battery,
then wait at least 3 minutes before starting work.
2. Confirm that each airbag, side airbag, side curtain airbag, seat belt tensioner, or seat belt buckle
tensioner is securely mounted.
3. Confirm that the deployment tool is functioning properly by following the check procedure on the
tool label.
4. Remove the access panel (A) from the steering wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel. 5. Remove the glove box, then disconnect the front
passenger’s airbag 4P connector (A) from the
dashboard wire harness.
6. Disconnect the side airbag 2P connector (A) from the floor wire harness.
7. Disconnect the floor wire harness 2P connector from the side curtain airbag (A).
08/08/21 14:01:58 61SNR030_240_0196
ProCarManuals.com
DYNOMITE -2009-




Installation
24-201
A
B
C
D
A
B
CA
B
D C
B
A
8. Disconnect the dashboard wire harness 4Pconnector (A) from the cable reel 4P connector (B),
then disconnect the dashboard wire harness 20P
connector (C) from the cable reel (D).
9. Release the lock tab (A) under the cable reel connector with a 90 ° hook shaped tool (B). Slide
the tool below the cable reel connector just above
the lock tab. Release the lower lock tab (C), and
slide the cable reel off the column. 1. Before installing the steering wheel, align the front
wheels straight ahead.
2. If not already done, disconnect the negative cable from the battery, then wait at least 3 minutes
before starting work.
3. Set the turn signal canceling sleeve (A) so that the projections (B) are aligned vertically.
4. Carefully install the cable reel (A) on the steering column shaft. Then connect 20P connector (B) to
the cable reel, and connect the 4P connector (C) to
the dashboard wire harness 4P connector (D).
(cont’d)
08/08/21 14:02:00 61SNR030_240_0201
ProCarManuals.com
DYNOMITE -2009-