2006 ACURA CSX audio

(#'#
)(#'#
)

µ
µ
µ
µ
µ
µ µ
µ
µ
µ
Navigation display stays on with ignition
switch in LOCK (0) Navigation cannot control audio system
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
23-12923-129
NOTE:
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, get the navigation system anti-theft code, then write down the audio presets.
 After troubleshooting, re-enter the anti-theft code, and re-initialize the navigation system, then enter the
audio presets.
 Check for aftermarket accessories that use the same power circuit. A feedback can cause this problem.
1. Remove the key from the ignition.
Go to step 2.
The system is OK at this time.
2. The vehicle may have been used as a demonstration vehicle at an event like an auto
show. In these events, power is often jumpered to
the navigation system so that the ignition key is not
needed in the vehicle. At the end of the show, the
jumper wire may not have been removed. Check
the navigation unit connector A (17P) for a non-
factory jumper wire in series with the factory cable.
Remove the jumper wire, and re-test. Return
the jumper wire to Tech Line.
Go to step 3.
3. Check if the audio unit works.
Troubleshoot the ACC circuit for a short to
power with another circuit.
Replace the navigation unit (see page 23-155). NOTE:
 Check the vehicle battery condition first.
 Verify that the correct navigation unit is installed for this model. Go into the Diagnostic mode and use
Version (see page 23-149).
 Check for connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have anti- theft codes for the navigation system.
 After troubleshooting, enter the anti-theft codes for the navigation system.
 Make sure that the correct navigation DVD color and version are installed.
 Inspect the navigation DVD for dirt or damage.
 Check any official Honda service website for more service information about the navigation system.
1. Make sure the anti-theft code for the navigation system is entered.
2. Go into the Diagnostic Menu and use the Navi System Link test (see page 23-136).
Do the troubleshooting for the voice
guidance cannot be heard (see page 23-122).
Go to step 3.
3. Substitute a known-good navigation unit (see page 23-155), and recheck.
Replace the navigation unit (see page 23-155).
Do the audio system troubleshooting.
Does t he nav i gat i on scr een st ay on?
Is t her e a j umper w i r e?Does the audio unit work with the ignition switchoff? Is the Radio icon red?
Can t he nav i gat i on cont r ol aud i o?
08/08/21 14:07:28 61SNR030_230_0132
ProCarManuals.com
DYNOMITE -2009-

(#'#
)
(#'#
)

µ
µ µ
µ
Navigation cannot control HVAC by voice
command Navigation cannot control XM radio
YES
NO YES
NO
23-13023-130Navigation System
Symptom Troubleshooting (cont’d)
NOTE:
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, get the navigation system anti-theft code.
 After troubleshooting, enter the navigation system anti-theft code.
 Verify that the correct navigation unit is installed for this model. Go into the Diagnostic Menu and use
Version (see page 23-149).
1. Go into the Diagnostic Menu and use the Navi System Link test (see page 23-136).
Dotheclimatecontrolsystem
troubleshooting.
Replace the navigation unit (see page 23-155). NOTE:
 Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
1. Substitute a known-good navigation unit (see page 23-155), and recheck.
Replace the navigation unit (see page 23-155).
Do the audio system troubleshooting.
Is the Air-con icon red? Can t he nav i gat i on cont r ol t he X M r ad i o?
08/08/21 14:07:28 61SNR030_230_0133
ProCarManuals.com
DYNOMITE -2009-

Î

Î

(#'#
)
µ
µ µ
µ
YES
NO YES
NO
OPEN/CLOSE function of the display does
not work
23-13223-132Navigation System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR A (17P)
RADIO GND
(BLK)
NAVIGATION UNIT CONNECTOR C (12P) GND (BLK)
4. Measure the voltage between navigation unitconnector A (17P) terminal No. 9 and body ground,
and between navigation unit connector C (12P)
terminal No. 4 and body ground.
Replace the navigation unit (see page 23-155).
Repair open in the wire between the
navigation unit and body ground (G 504, G505).NOTE:
 Check the vehicle battery condition first.
 If the display’s Open/Close button does not work, you must manually open the display to obtain the client’s
navigation DVD, audio CD, and PC card (see page
23-154).
1. Press the OPEN/CLOSE button.
The system is OK at this time.
Replace the navigation unit (see page 23-155).
Wire side of female terminals
Wire side of female terminals
Is t her e l ess t han 0.1 V ? Does t he d i spl ay open and / or cl ose nor mal l y ?
08/08/21 14:07:28 61SNR030_230_0135
ProCarManuals.com
DYNOMITE -2009-

´µ ´µ
Î
Î
Î
Î
´
µ
´
µ
´µ
PC Card info
Hard KeyCar Status
23-141
PC Card Information
ReturnReturn
PC Card is not inserted.
PC Card Information Return
Manufacturer xxxxxx
Product Name xxxxxx
FILES
Hard KeyReturn
ZOOM OUT ZOOM IN
CANCEL SET UP MAP
MENU INFO
MODE CH
CH
VOL
VOL
FF
REW
RPT RDM
SEEK UP SCAN
AUDIO
CD/AUX AM/FMSKIP
SKIP
SEEK DOWN Keep Pushing to Return.
Car Status
0
VSP 0
ILL
0
BACK Close
Display
0
ILL CANCEL
There is no PC card in the PC slot, and the screen
should display, PC card is not inserted.
If the factory provides a PC card and instructs you to
insert it, the screen displays the Manufacturer, and
Product Name as shown in the following screen. Touch
the FILES button to see the contents of the card.
This diagnostic screen checks the status of each of the
hard buttons surrounding the navigation display. When
you press each hard button, the corresponding item on
the screen should flash blue. Touch the return key, or
press and hold the joystick to exit.
NOTE: It is normal for the VOL ( , ) CH ( , ) and
MODEbuttontobeinactive. Use this screen to confirm that navigation unit is
properly receiving input signals. Signals equal to (0) are
OFF, and signals equal to (1) are ON. If the value on the
display does not match the actual vehicle status, then
check the wire carrying the signal.
 VSP-Vehicle Speed Pulse from ECM/PCM connector A (Navigation unit connector A (17P) terminal No. 13)
a) OFF (0) when vehicle is not moving
b) ON (1) when vehicle is moving
The VSP comes from the ECM/PCM as a dedicated
signal. Internally, the navigation unit compares the
actual VP on the map against street data to adjust the
pulse to speed scaling factor.
 BACK-Reverse indication from taillight relay (Navigation unit connector C (12P) terminal No. 7)
a) OFF (0) when shift lever is in any position other
than reverse
b) ON (1) when shift lever is in reverse
The Back signal is used by the navigation unit to allow
the map screen to show the VP moving backwards
when in reverse and to trigger the optional rear view
camera. This signal is needed because the Speed Pulse
does not provide any directional information to the
system.
ILLCANCEL a) OFF (0) when the dash lights brightness control
button is less than 90 % brightness with the
headlights turned on.
b) ON (1) when the dash lights brightness control
button is more than 90 % brightness with the
headlights turned on.
(cont’d)
08/08/21 14:07:31 61SNR030_230_0144
ProCarManuals.com
DYNOMITE -2009-


(#'#

 )
23-155
Navigation Unit Removal/Installation
A B B
C
SRS components are located in this area. Review the
SRS component location (see page 24-11).
Also review the precautions and procedures (see page
24-13) in the SRS section before doing repairs or
service.
NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the dashboard and related parts.
 Lay a workshop towel under the parts when working on them to protect the face panel from scratches or
other damage.
 Do not work in a dusty or dirty place.
 Discharge static electricity from your body before and during the work.
 Do not touch the circuit board(s) with your bare hands.
 Do not work with dirty hands.
 Be careful not to fold the flat plate cable.
 Do not touch the terminal connector of the flat plate cable with your bare hands. (If you have touched it,
wipe it off thoroughly.)
 Before replacing the navigation unit, make sure to remove the client’s navigation DVD, and their audio
CD, or PC card. Remanufactured navigation units do
not come with a navigation DVD. Re-install the client’s
navigation DVD, audio CD, and audio PC card into the
new Remanufactured unit. If the navigation display
won’t open, manually remove the navigation DVD,
audio CD, and PC card (see page 23-154).
 If you are replacing the navigation unit, write down the audio presets (if possible), then enter then into
the new navigation unit.
1. Make sure you have the 4-digit anti-theft code for the navigation system.
2. Eject the DVD from the original navigation unit. To avoid scratching or damaging the DVD, temporarily
place the DVD in a jewel case.
3. Remove the meter inner visor (see page 20-100). 4. Remove the center pocket hole lid and bolts, then
pull out the center panel (A).
5. Disconnect the connectors (B) and the air hose (C), then remove the center panel.
(cont’d)
08/08/21 14:08:39 61SNR030_230_0158
ProCarManuals.com
DYNOMITE -2009-

(#'#

 )

(#'#


 )
23-15723-157
Voice Control Switch Replacement Microphone Replacement
B E
D
A C
B
A
A B
SRS components are located in this area. Review the
SRS component location (see page 24-11).
Also review the precautions and procedures (see page
24-13) in the SRS section before doing repairs or
service.
1. Remove the steering wheel (see page 17-6).
2. Remove the voice control switch (see page 17-7).
3. Install the audio remote switch in the reverse order of removal. 1. Remove the front individual map light lens (A).
2. Remove the bolts (B), then disconnect the
connectors, and remove the map lights housing (C).
3. Carefully pry off the moonroof switch (D) from the map light housing while pressing in on the
retaining tabs (E).
4. From the moonroof switch (A), remove the screw and microphone (B).
5. Install the microphone in the reverse order of removal.
08/08/21 14:08:39 61SNR030_230_0160
ProCarManuals.com
DYNOMITE -2009-

(#'/)
Audio, Navigation, andTelematics
Audio System
Navigation System HandsFreeLink System
Audio, Navigation, and Telematics (’09 model)
....................... .......................
Special Tools . 23-160
.................................
................................. .............
................... .....
..........................
..................
........................
........................ ....................
........................ .........
....................
....................
................................... ....................
....................
....................
...............................
.................................
.................................
.............
................... .....
..........................
..................
........................
........................ ....................
........................ .........
....................
....................
................................... ....................
....................
....................
...............................
Component Location
Index . 23-161
Symptom Troubleshooting Index . 23-162
System Description . 23-164
Circuit Diagram . 23-184
Self-diagnostic Function . 23-190
Error Codes . 23-194
Symptom Troubleshooting . 23-196
Sound Quality Diagnosis . 23-251
Audio Unit Removal/ Installation . 23-256
XM Receiver Removal/ Installation . 23-258
USB Adapter Unit Replacement . 23-258
Stereo Amplifier Removal/ Installation . 23-259
Speaker Replacement . 23-259
Auxiliary Jack Assembly Replacement . 23-261
USB Adapter Replacement . 23-262
Audio Remote Switch Test . 23-262
Audio Remote Switch Replacement . 23-263
AM/FM Antenna Amplifier Replacement . 23-263
XM Antenna Replacement . 23-264
AM/FM Antenna Repair . 23-264
.......................................................
.................................
......................
Component Location
Index . 23-265
General Troubleshooting Information . 23-266 .................................
.................................
.............
................... ...
.........
.............. .......
........................ ..
....................
....................
........................
.................................
.................................
.............
................... ...
.........
.............. .......
........................ ..
....................
....................
........................
DTC Troubleshooting
Index . 23-275
Symptom Troubleshooting Index . 23-276
System Description . 23-279
Circuit Diagram . 23-296
System Diagnostic Mode . 23-297
DTC Troubleshooting . 23-320
Symptom Troubleshooting . 23-338
CD, DVD, and PC Card Removal/Installation . 23-354
Navigation Unit Removal/ Installation . 23-355
Voice Control Switch Test . 23-357
Voice Control Switch Replacement . 23-357
HFL-Navigation Microphone Replacement . 23-358
GPS Antenna Removal/ Installation . 23-358
................................. ......................
.................................
................................. .............
..............
................... .........
..............
...................
....................
.................................
......................
.................................
................................. .............
..............
................... .........
..............
...................
....................
Component Location
Index . 23-359
General Troubleshooting Information . 23-360
DTC Troubleshooting Index . 23-370
Symptom Troubleshooting Index . 23-371
System Description . 23-372
HFL System Troubleshooting . 23-373
Circuit Diagram . 23-374
DTC Troubleshooting . 23-376
Symptom Troubleshooting . 23-382
HFL Switch Test . 23-387
Control Unit Input Test/ Replacement . 23-388
08/08/21 14:08:40 61SNR030_230_0162
ProCarManuals.com
DYNOMITE -2009-


(#'%)Ref. No. Tool Number Description Qty
23-160
Audio, Navigation, and Telematics
Special Tools
07AAZ-SDBA100
Diagnostics CD 1
07AAZ-SDBA200 (ABEX-TCD-725B) Skip Test CD 1
07AAZ-SDBA300 (ABEX-TCD-721) Skip Test CD 1
,,
08/08/21 14:08:40 61SNR030_230_0163
ProCarManuals.com
DYNOMITE -2009-