2006 ACURA CSX ignition


µ
µ
µ
µ µ
µ
YES
NO
YES
NO
YES
NO
11-107
SECONDARY HO2S (SENSOR 2) 4P CONNECTOR
SHO2S (WHT)JUMPER WIRE ECM/PCM CONNECTOR C (44P)
SHO2S (WHT/RED)
9. Turn the ignition switch to ON (II).
10. Check the HO2S S2 in the DATA LIST with the HDS.
Go to step 11.
Go to step 20.
11. Turn the ignition switch to LOCK (0).
12. Remove the jumper wire from the secondary HO2S (Sensor 2) 4P connector.
13. Connect secondary HO2S (Sensor 2) 4P connector terminal No. 2 to body ground with a jumper wire.
14. Turn the ignition switch to ON (II).
15. Check the HO2S S2 in the DATA LIST with the HDS. Go to step 16.
Repair open in the wire between the ECM/
PCM (A9) and the secondary HO2S (Sensor 2), then
go to step 22. 16. Turn the ignition switch to LOCK (0).
17. Jump the SCS line with the HDS.
18. Disconnect ECM/PCM connector C (44P).
19. Check for continuity between ECM/PCM connector
terminal C27 and body ground.
Go to step 30.
Repair open in the wire between the ECM/
PCM (C27) and the secondary HO2S (Sensor 2),
then go to step 22.
20. Turn the ignition switch to LOCK (0).
21. Replace the secondary HO2S (Sensor 2) (see page 11-221).
22. Reconnect all connectors.
23. Turn the ignition switch to ON (II).
24. Reset the ECM/PCM with the HDS.
25. Do the ECM/PCM idle learn procedure (see page 11-310).
(cont’d)
Terminal side of male terminals Terminal side of female terminals
Does t he v ol t age st ay at 1.27 V or mor e?
Does t he v ol t age st ay at 1.27 V or mor e? Is there continuity?
08/08/21 14:17:22 61SNR030_110_0107
ProCarManuals.com
DYNOMITE -2009-

(#' 

)
µ
µ µ
µ
µ
µ
DTC P0139:
YES
NO YES
NO
YES
NO
11-109
Secondary HO2S (Sensor 2) Slow
Response
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine. Hold the engine speed at 3,000 rpm (A/T in P or N, M/T in neutral) until the
radiator fan comes on, then let it idle.
4. Test-drive under these conditions:  Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
 A/TinD,M/Tin4th
 Vehicle speed at 56 km/h (35 mph)
 Drive about 15 seconds
5. Monitor the OBD STATUS for DTC P0139 in the DTCs MENU with the HDS.
Go to step 6.
If the screen indicates PASSED, intermittent
failure, the system is OK at this time. Check for
poor connections or loose terminals at the
secondary HO2S (Sensor 2) and the ECM/PCM. If
the screen indicates EXECUTING, keep driving until
a result comes on. If the screen indicates OUT OF
CONDITION, go to step 3 and recheck.
6. Turn the ignition switch to LOCK (0).
7. Replace the secondary HO2S (Sensor 2) (see page 11-221).
8. Turn the ignition switch to ON (II).
9. Reset the ECM/PCM with the HDS.
10. Do the ECM/PCM idle learn procedure (see page 11-310).
11. Start the engine, and let it idle without load (A/T in P or N, M/T in neutral) until the radiator fan comes
on. 12. Test-drive under these conditions:
 Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
 A/TinD,M/Tin4th
 Vehicle speed at 56 km/h (35 mph)
 Drive about 15 seconds
13. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the secondary HO2S (Sensor 2) and
theECM/PCM,thengotostep1.
Go to step 14.
14. Monitor the OBD STATUS for DTC P0139 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 13,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the secondary
HO2S(Sensor2)andtheECM/PCM,thengotostep
1. If the screen indicates EXECUTING, keep driving
until a result comes on. If the screen indicates OUT
OF CONDITION, go to step 11.
Does t he scr een i nd i cat e F AILE D? Is DT C P0139 ind icated ?
Does t he scr een i nd i cat e PASSE D?
08/08/21 14:17:22 61SNR030_110_0109
ProCarManuals.com
DYNOMITE -2009-

µ


(#' 


)
µ
µ
µ
µ µ
µ
µ
µ
DTC P0141:
YES
NO
YES
NO YES
NO
YES
NO
11-110PGM-FI System
DTC Troubleshooting (cont’d)
SECONDARY HO2S (SENSOR 2) 4P CONNECTOR
SECONDARY HO2S (SENSOR 2) 4P CONNECTOR
Secondary HO2S (Sensor 2)
Heater Circuit Malfunction
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the secondary HO2S (Sensor 2) and the ECM/
PCM.
5. Turn the ignition switch to LOCK (0).
6. Check the No. 3 ALTERNATOR (10 A) fuse in the under-dash fuse/relay box.
Go to step 7.
Repair short in the wire between the
secondary HO2S (Sensor 2) and the No. 3
ALTERNATOR (10 A) fuse. Also replace the No. 3
ALTERNATOR (10 A) fuse, then go to step 23.
7. Disconnect the secondary HO2S (Sensor 2) 4P connector. 8. At the secondary HO2S (Sensor 2) side, measure
the resistance between secondary HO2S (Sensor 2)
4P connector terminals No. 3 and No. 4.
Go to step 9.
Go to step 22.
9. At the secondary HO2S (Sensor 2) side, check for continuity between body ground and secondary
HO2S (Sensor 2) 4P connector terminals No. 3 and
No. 4 individually.
Go to step 22.
Go to step 10.
Wire side of female terminals
Wire side of female terminalsIs DTC P0141 indicated?
IsthefuseOK? Is t her e 5.4 7 .3 at r oom t emper at ur e?
Is there continuity?
08/08/21 14:17:23 61SNR030_110_0110
ProCarManuals.com
DYNOMITE -2009-



µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
11-111
SECONDARY HO2S (SENSOR 2) 4P CONNECTOR
SO2SHTC (PNK) IG1 (YEL) ECM/PCM CONNECTOR B (44P)
SO2SHTC (BLK/WHT)
SECONDARY HO2S (SENSOR 2) 4P CONNECTOR IG1 (YEL)
10. Turn the ignition switch to ON (II).
11. Measure the voltage between secondary HO2S(Sensor 2) 4P connector terminals No. 3 and No. 4.
Go to step 12.
Go to step 16.
12. Turn the ignition switch to LOCK (0).
13. Jump the SCS line with the HDS.
14. Disconnect ECM/PCM connector B (44P). 15. Check for continuity between ECM/PCM connector
terminal B4 and body ground.
Repair short in the wire between the ECM/
PCM (B4) and the secondary HO2S (Sensor 2), then
go to step 23.
Go to step 29.
16. Measure the voltage between secondary HO2S (Sensor 2) 4P connector terminal No. 4 and body
ground.
Go to step 17.
Repair open in the wire between the
secondary HO2S (Sensor 2) and the No. 3
ALTERNATOR (10 A) fuse, then go to step 23.
(cont’d)
Terminal side of male terminals Terminal side of female terminals
Terminal side of male terminals
Is there battery voltage? Is there continuity?
Is there battery voltage?
08/08/21 14:17:23 61SNR030_110_0111
ProCarManuals.com
DYNOMITE -2009-


µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-112PGM-FI System
DTC Troubleshooting (cont’d)
SECONDARY HO2S (SENSOR 2) 4P CONNECTOR
SO2SHTC (PNK)JUMPER WIRE
ECM/PCM CONNECTOR B (44P) SO2SHTC (BLK/WHT)
17. Turn the ignition switch to LOCK (0).
18. Jump the SCS line with the HDS.
19. Disconnect ECM/PCM connector B (44P).
20. Connect secondary HO2S (Sensor 2) 4P connectorterminal No. 3 to body ground with a jumper wire.
21. Check for continuity between ECM/PCM connector terminal B4 and body ground.
Go to step 29.
Repair open in the wire between the ECM/
PCM (B4) and the secondary HO2S (Sensor 2), then
go to step 23. 22. Replace the secondary HO2S (Sensor 2) (see page
11-221).
23. Reconnect all connectors.
24. Turn the ignition switch to ON (II).
25. Reset the ECM/PCM with the HDS.
26. Do the ECM/PCM idle learn procedure (see page 11-310).
27. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the secondary HO2S (Sensor 2) and
theECM/PCM,thengotostep1.
Go to step 28.
28. Monitor the OBD STATUS for DTC P0141 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 27,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the secondary
HO2S(Sensor2)andtheECM/PCM,thengotostep
1. If the screen indicates NOT COMPLETED, keep
idling until a result comes on.
Terminal side of male terminals
Terminal side of female terminals
Is there continuity? Is DTC P0141 indicated?
Does t he scr een i nd i cat e PASSE D?
08/08/21 14:17:24 61SNR030_110_0112
ProCarManuals.com
DYNOMITE -2009-

µµµ
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
11-114
PGM-FI System
DTC Troubleshooting (cont’d)
2. Check for vacuum leaks at these parts:
 PCV valve
 PCV hose
 EVAP canister purge valve
 Throttle body
 Intake manifold
 Brake booster
 Brake booster hose
 Intake air duct
Go to step 3.
Repair or replace the part(s) with leaks, then
go to step 7.
3. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
4. Check for these conditions:  Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
 A/T in N, M/T in neutral
 All electrical loads off
5. Monitor the ENGINE SPEED in the DATA LIST with the HDS, and hold the engine speed at 2,500 rpm.
Once the engine speed is met, hold the accelerator
pedal steady for more than 10 seconds.
Repeat step 5.
Go to step 6. 6. While holding the engine speed at 2,500 rpm, check
the MAF SENSOR in the DATA LIST with the HDS.
Check the engine valve clearances and adjust
them if needed; K20Z2 engine (see page 6-12),
K20Z3 engine (see page 6-14). If the valve
clearances are OK, replace the injectors (see page
11-219), then go to step 7.
Replace the MAF sensor/IAT sensor (see page
11-224), then go to step 7.
7. Turn the ignition switch to ON (II).
8. Reset the ECM/PCM with the HDS.
9. Do the ECM/PCM idle learn procedure (see page 11-310).
10. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
11. Test-drive under these conditions:  Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
 A/TinD,M/Tin4th
 Drive at a steady speed between 24 120 km/h (15 75 mph) for 15 minutes
NOTE: DTC P0171 and/or P0172 may take up to
80 minutes of test driving to set. Using the HDS,
monitor or the air fuel feed back average (AF FB
AVE). If the AF FB AVE stays within 0.80 1.25,
there is no problem at this time.
12. Check for Temporary DTCs or DTCs with the HDS.
Go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
Ar e t he par t s OK ?
Di d t he engi ne speed v ar y mor e t han 100 r pm f r om2,500 rpm? Is t her e about 6.0 8.6 ( K 20Z 2 engi ne) or 5.7
8.3(K20Z3engine)gm/s?
I s DT C P017 1 or P017 2 i nd i cat ed ?
08/08/21 14:17:24 61SNR030_110_0114
ProCarManuals.com
DYNOMITE -2009-

(#' 
)µ
µ
µ
µ
µ
µ
DTC P0300:
DTC P0301:
DTC P0302:
DTC P0303:
DTC P0304:
Special Tools Required YES
NO
YES
NO
YES
NO
11-115
Random Misfire and Any
Combination of the Following:
No. 1 Cylinder Misfire Detected
No. 2 Cylinder Misfire Detected
No. 3 Cylinder Misfire Detected
No. 4 Cylinder Misfire Detected
 Pressure gauge adapter 07NAJ-P07010A
 A/T low pressure gauge w/panel 07406-0070301
 A/T pressure hose 07406-0020201
 A/T pressure hose, 2,210 mm 07MAJ-PY4011A
 A/T pressure hose, adapter 07MAJ-PY40120
 Oil pressure hose 07ZAJ-S5AA200
NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
 If the misfire is frequent enough to trigger detection of increased emissions during two consecutive
driving cycles, the MIL will come on, and DTC P0300
(and some of the combination of P0301 thr ough
P0304) will be stored.
 If the misfire is frequent enough to damage the catalyst, the MIL will blink whenever the misfire
occurs, and DTC P0300 (and some of the combination
of P0301 through P0304) will be stored. When the
misfire stops, the MIL will remain on.
 If any of the DTCs listed below are indicated at the same time as the random misfire DTCs, troubleshoot
those DTCs first, then recheck for random misfire
DTCs:
P0101, P0102, P0103: Mass air flow (MAF) sensor
P0107, P0108: Manifold absolute pressure (MAP)
sensor
P0171, P0172: Fuel system
P0335, P0339: Crankshaft position (CKP) sensor
P0365, P0369: Camshaft position (CMP) sensor B
P0401 , P0404 , P0416 , P2413 : Exhaust gas
recirculation (EGR) system
P0506, P0507: Idle control system
P2646, P2647, P2648, P2649: VTEC system : K20Z2 engine 1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and let it idle without load (A/T in
P or N, M/T in neutral).
4. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Go to step 9.
If the screen indicates PASSED, go to step 5. If
the screen indicates EXECUTING, keep idling until
a result comes on. If the screen indicates OUT OF
CONDITION, wait for several minutes, then recheck.
5. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 9.
Go to step 6.
6. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
 ENGINE S PEED
 VSS
 REL TP SENSOR
 CLV (calculated load value)
 APP SENSOR
7. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Go to step 9.
If the screen indicates PASSED, go to step 8. If
the screen indicates EXECUTING, keep driving until
a result comes on. if the screen indicates OUT OF
CONDITION, go to step 6 and recheck.
(cont’d)
Does t he scr een i nd i cat e F AILE D?
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts?
Does t he scr een i nd i cat e F AILE D?
08/08/21 14:17:24 61SNR030_110_0115
ProCarManuals.com
DYNOMITE -2009-

µ
µ
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
11-116
PGM-FI System
DTC Troubleshooting (cont’d)
8. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3
MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 9.
Intermittent failure, the system is OK at this
time.
9. Turn the ignition switch to LOCK (0).
10. Check the fuel quality.
Go to step 11.
Drain the tank, fill it with a known-good fuel,
then go to step 25.
11. Inspect the spark plugs (see page 4-21). If the spark plugs are fouled or worn, replace them.
12. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
 ENGINE S PEED
 VSS
 REL TP SENSOR
 CLV (calculated load value)
 APP SENSOR
13. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 14.
Go to step 25. 14. Check the fuel pressure (see page 11-325).
Go to step 15.
 If the fuel pressure is too high, replace the fuel pressure regulator (see page 11-337), then go to
step 25.
 If the fuel pressure is too low, check the fuel pump, the fuel feed pipe, and the fuel filter. If
they are OK, replace the fuel pressure regulator
(see page 11-337), then go to step 25.
15. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
16. Check for these conditions:  Engine coolant temperature (ECT SENSOR 1)above80°C(176°F)
 A/T in P or N, M/T in neutral
 All electrical loads off
17. Monitor the ENGINE SPDEED in the DATA LIST with the HDS, and hold the engine speed at
2,500 rpm. Once the engine speed is met, hold the
accelerator pedal steady for more than 10 seconds.
Repeat step 17.
Go to step 18.
18. While holding the engine speed at 2,500 rpm, check the MAF SENSOR in the DATA LIST with the HDS.
Go to step 19.
Replace the MAF sensor/IAT sensor (see page
11-224), then go to step 25.
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts?
Is the quality good?
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts? Is the fuel pressure OK?
Di d t he engi ne speed v ar y mor e t han 100 r pm f r om2,500 rpm?
Is t her e about 6.0 8.6 ( K 20Z 2 engi ne) or5.7 8.3 (K 20Z 3 engine) gm/ s?
08/08/21 14:17:24 61SNR030_110_0116
ProCarManuals.com
DYNOMITE -2009-