2006 ACURA CSX ignition

(#')
µ
µ µ
µ
µ
µ
Passenger’s airbag cutoff indicator stays on
or comes on suddenly
YES
NO YES
NO
YES
NO
24-184SRS
Symptom Troubleshooting (cont’d)
NOTE: Under the following conditions, the passenger’s
airbag cutoff indicator stays on or comes on suddenly.
 No one is sitting the front passenger’s seat, but there is an object on the seat more than 5 kg (11 lbs).
 The seat belt is buckled, but no one is sitting on the front passenger’s seat.
 Someone who is less than 30 kg (66 lbs) is sitting on the front passenger’s seat.
 Someone who is more than 30 kg (66 lbs) but is supporting some of their body weight on their legs,
feet, arms, or hands.
1. Check for these items, then recheck the passenger’s airbag cutoff indicator.
 The front passenger’s seat is/was installed correctly.
 Nothing is/was on the front passenger’s seat.
 Nothing is/was under the front passenger’s seat.
 Nothing is/was in the front passenger’s seat-back pocket.
 Whoever was sitting on the passenger’s seat was sitting in the proper sitting position.
Go to step 2.
Troubleshooting is complete.
2. Connect the HDS to the data link connector (DLC) (see page 24-22).
3. Turn the ignition switch to ON (II).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).5. Select the INSPECTION menu on the HDS, then
select AFTER REPLACING FRONT PASSENGER’S
SEAT COMPONENT(S), and follow the prompts.
Go to step 6.
Troubleshooting is complete.
6. Select the INSPECTION menu on the HDS, then select AFTER A VEHICLE COLLISION, and follow
the prompts.
Replace the SRS unit (see page 24-203). If the
problem is still present, replace the ODS unit
(see page 24-209), and then if the problem is still
present, replace the passenger’s weight sensors
(see page 24-207).
Troubleshooting is complete.
Does the passenger’s airbag cutof f indicator stayon? Does t he passenger ’ s ai r bag cut of f i nd i cat or st ay
on?
Does t he passenger ’ s ai r bag cut of f i nd i cat or st ayon?
08/08/21 14:01:53 61SNR030_240_0184
ProCarManuals.com
DYNOMITE -2009-



A-Pillar Trim
B-Pillar Trim C-Pillar Trim
24-186SRS
Component Replacement/Inspection After Deployment (cont’d)
During the repair process, inspect these areas:
 Inspect all the SRS wire harnesses. Replace, do not repair, any damaged harnesses.
 Inspect the cable reel for heat damage. If there is any damage, replace the cable reel.
After the vehicle is completely repaired, turn the
ignition switch to ON (II). If the SRS indicator comes on
for about 6 seconds and then goes off, the SRS is OK. If
the indicator does not function properly, use the HDS to
read the DTC (see page 24-22). If you cannot retrieve a
code, Do the SRS Symptom Troubleshooting.
Always replace.
Always replace.
08/08/21 14:01:53 61SNR030_240_0186
ProCarManuals.com
DYNOMITE -2009-

Î
 
Î
(#'
 )
Removal Installation
24-188SRS
Driver’s Airbag Replacement
A
B
A
B
C
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
B
A B
NOTE: If replacing the driver’s airbag after deployment,
refer to Component Replacement/Inspection After
Deployment (see page 24-185) for a complete list of
other parts that must also be replaced.
1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the access panel (A) from the steering wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel.
3. Using a TORX T30 bit, remove the two TORX bolts (A) and discard them.
4. Disconnect the horn switch connector (1P), then remove the driver’s airbag (B). 1. Connect the horn switch connector (1P) (A) to the
driver’s airbag.
2. Place the driver’s airbag (B) in the steering wheel, and secure it with new TORX bolts (C).
3. Connect the driver’s airbag 4P connector (A) to the cable reel 4P connector, then install the access
panel (B) on the steering wheel.
4. Do the battery terminal reconnection procedure (see page 22-68).
5. Clear any DTCs (see page 24-23).
6. After installing the airbag, confirm proper system operation:
 Turn the ignition switch to ON (II); the SRS indicator should come on for about 6 seconds
andthengooff.
 Make sure the horn works.
Replace.
08/08/21 14:01:55 61SNR030_240_0188
ProCarManuals.com
DYNOMITE -2009-




Installation
24-190SRS
Front Passenger’s Airbag Replacement (cont’d)
A
A
B
A
B B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
A
6. Cut the four parts (A) of the front passenger’s lid (B)as shown, and remove the front passenger’s airbag.
NOTE: Always replace the front passenger’s lid whenever you remove the front passenger’s
airbag from the lid.
 Replace the front passenger’s airbag if the airbag mounting hooks or its housing is damaged.
7. Insert the hooks (A) of the front passenger’s airbag housing into the new front passenger’s lid, then
insert the other hooks (B) into the lid.
NOTE: Make sure there are no objects between the airbag and the front passenger’s lid.
 Make sure the airbag is fully seated, and make sure the front passenger’s lid is not deformed or
damaged after the airbag is in place.
 Do not use tools when detaching the front passenger’s airbag in order to protect it. 1. Place the front passenger’s airbag assembly (A)
into the dashboard. Tighten the front passenger’s
airbag mounting nuts (B).
2. Connect the front passenger’s airbag 4P connector (A) to dashboard wire harness, then reinstall the
glove box and center panel.
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Clear any DTC (see page 24-23).
5. After installing the airbag, confirm proper system operation: Turn the ignition switch to ON (II); the
SRS indicator should come on for about 6 seconds
andthengooff.
08/08/21 14:01:56 61SNR030_240_0190
ProCarManuals.com
DYNOMITE -2009-


Î
(#'
 )
Removal Installation
24-191
Side Airbag Replacement
AB
A
B
6.3 N·m
(0.64 kgf·m, 4.65 lbf·ft)
NOTE: If replacing the side airbag after deployment,
refer to Component Replacement/Inspection After
Deployment (see page 24-185) for a complete list of
other parts that must also be replaced. 1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the seat assembly (see page 20-118) and seat-back cover (see page 20-123).
3. Remove the mounting screws (A) and the side airbag (B). NOTE:
 If the side airbag lid is secured by tape, remove the tape.
 Do not open the lid of the side airbag cover.
 Use new mounting screws tightened to the specified torque. When you replace a side airbag, make sure
that the seat-back cover is installed properly.
Improper installation may prevent proper
deployment.
 Be sure to install the harness wires so that they are not pinched or interfering with other parts.
1. Place the side airbag on the seat-back frame (A). Install new side airbag mounting screws (B).
2. Install the seat-back cover in the reverse order of removal (see page 20-123).
3. Install the seat assembly (see page 20-118).
4. Move the front seat and the seat-back through their full ranges of movement, making sure the harness
wires are not pinched or interfering with other parts.
5. Do the battery terminal reconnection procedure (see page 22-68).
6. Clear any DTCs (see page 24-23).
7. After installing the side airbag, confirm proper system operation: Turn the ignition switch to ON
(II); the SRS indicator should come on for about
6 seconds and then go off.
Replace.
08/08/21 14:01:56 61SNR030_240_0191
ProCarManuals.com
DYNOMITE -2009-


24-195
A
2. Connect the side curtain airbag 2P connector (A) to the floor wire harness.
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Clear any DTCs (see page 24-23).
5. After installing the side curtain airbag, confirm proper system operation: Turn the ignition switch to ON (II); theSRS indicator should come on for about 6 seconds and then go off.
6. Install all removed parts.
7. Confirm proper headliner/pillar trim overlap (see page 24-187).
Left side shown; right side is similar.
08/08/21 14:01:57 61SNR030_240_0195
ProCarManuals.com
DYNOMITE -2009-

Î


Î
(#'
!)
Special Tools Required
Driver’s Airbag
Front Passenger’s Airbag
Side Airbag
Side Curtain Airbag
Deploying Airbags in the Vehicle
24-196
SRS
Airbag and Tensioner Disposal
A
B
A
A
A
Deployment tool 07HAZ-SG00500
Before scrapping any airbags, side airbags, side curtain
airbags, seat belt tensioners, or seat belt buckle
tensioner (including those in a whole vehicle to be
scrapped), the part(s) must be deployed. If the vehicle is
still within the warranty period, the Honda District Parts
and Service Manager must give approval and/or special
instructions before deploying the part(s). Only after the
part(s) have been deployed (as the result of vehicle
collision, for example), can they be scrapped.
If the parts appear intact (not deployed), treat them with
extreme caution. Follow this procedure.
If an SRS equipped vehicle is to be entirely scrapped, its
airbags, side airbags, side curtain airbags, seat belt
tensioners, and seat belt buckle tensioner should be
deployed while still in the vehicle. These parts should
not be considered as salvageable parts and should
never be installed in another vehicle.1. Turn the ignition switch to LOCK (0), then disconnect the negative cable from the battery,
then wait at least 3 minutes before starting work.
2. Confirm that each airbag, side airbag, side curtain airbag, seat belt tensioner, or seat belt buckle
tensioner is securely mounted.
3. Confirm that the deployment tool is functioning properly by following the check procedure on the
tool label.
4. Remove the access panel (A) from the steering wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel. 5. Remove the glove box, then disconnect the front
passenger’s airbag 4P connector (A) from the
dashboard wire harness.
6. Disconnect the side airbag 2P connector (A) from the floor wire harness.
7. Disconnect the floor wire harness 2P connector from the side curtain airbag (A).
08/08/21 14:01:58 61SNR030_240_0196
ProCarManuals.com
DYNOMITE -2009-



24-202SRS
Cable Reel Replacement (cont’d)
A
D
B
A C A
39 N·m
(4.0 kgf·m, 29 lbf·ft)
5. Install the steering column covers.
6. If necessary, center the cable reel (new
replacement cable reels come centered). Do this by
first rotating the cable reel clockwise until it stops.
Then rotate it counterclockwise (about three turns)
until the arrow mark (A) on the cable reel label
points straight up.
7. Position the two tabs (A) of the turn signal canceling sleeve (B) as shown, and install the
steering wheel on to the steering column shaft,
making sure the steering wheel hub (C) engages
the pins (D) of the cable reel and tabs of the turn
signal canceling sleeve. Do not tap on the steering
wheel or steering column shaft when installing the
steering wheel. 8. Install a new steering wheel bolt (A), then
reconnect the connectors.
9. Install the driver’s airbag (see page 24-188).
10. Do the battery terminal reconnection procedure (see page 22-68).
11. Clear any DTCs (see page 24-23).
12. After installing the cable reel, confirm proper system operation:
 Turn the ignition switch to ON (II); the SRS indicator should come on for about 6 seconds
andthengooff.
 After the SRS indicator has turned off, turn the steering wheel fully left and right to confirm the
SRS indicator does not come on.
 Make sure the horn and turn signal switches work properly.
 Make sure the steering wheel switches work properly.
Replace.
08/08/21 14:02:00 61SNR030_240_0202
ProCarManuals.com
DYNOMITE -2009-