2005 TOYOTA AVENSIS wiring

±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
05±319
AVENSIS REPAIR MANUAL (RM1018E)Symbols (Terminal No.)
STD Voltage (V)
Condition
Wiring Color
OX1A (E12±22) ± E2 (E13±28)B ±BR
OX1B (E12±21)
± O1B± (E11±26)B ±WMaintain engine speed at 2,500 rpm for 2 minutes after warmingPulse generation
OX2A (E12±23) ± E2 (E13±28)R ±BR
Maintain engine seed at 2,500 rm for 2 minutes after warming
up
Pulse generation
(See page 05±363)
OX2B (E12±29)
± O2B± (E11±31)R ± G
(g )
HT1A (E12±5) ± E03 (E11±7)
HT1B (E12±25) ± E03 (E11±7)Y ± W±B
P ± W±BIdlingBelow 3.0()()
HT2A (E12±4) ± E03 (E11±7)
HT2B (E12±33) ± E03 (E11±7)L ± W±B
L±B
±W±BIG switch ON9 to 14
KNK1 (E12±1) ± EKNK (E12±2)B ± WMaintain engine speed at 4,000 rpm after warming upPulse generation
(See page 05±429)
OC1+ (E11±16) ± OC1± (E11±15)W±G ± Y±BIG switch ONPulse generation
(See page 05±322)
EVP1 (E13±34) ± E01 (E13±7)W±G ± W±BIG switch ON9 to 14
SCV (E13±5) ± E1 (E11±1)L±B ± BRIG switch ON9 to 14
PIM (E13 33) E2 (E13 28)GW BRIG switch ON3.3 to 3.9PIM (E13±33) ± E2 (E13±28)G±W ± BRApply vacuum 26.7 kPa (200 mmHg, 7.9 in.Hg)2.6 to 3.0
PB (E13 26) E2 (E13 28)YBRIG switch ON3.3 to 3.9PB (E13±26) ± E2 (E13±28)Y ± BRApply vacuum 26.7 kPa (200 mmHg, 7.9 in.Hg)2.6 to 3.0
PR (E13±23) ± E2 (E13±28)Y±G ± BRIdling2.1 to 3.2
FP+ (E12±6) ± E1 (E11±1)R ± BRIdlingPulse generation FP+ (E12 6) E1 (E11 1)
FP± (E12±3) ± E1 (E11±1)
R BR
G ± BRIdlingPulse generation
(See page 05±477)
STA (E13±17) ± E1 (E11±1)B±Y ± BRShift position in neutral, IG switch START6.0 or more
STP (E10 19) E1 (E11 1)GW BRBrake pedal is depressed9 to 14STP (E10±19) ± E1 (E11±1)G±W ± BRBrake pedal is releasedBelow 1.5
ST1 (E10 12) E1 (E11 1)GW BRIG switch ON, Brake pedal is depressedBelow 1.5ST1± (E10±12) ± E1 (E11±1)G±W ± BRIG switch ON, Brake pedal is released7.5 to 14
W (E9 11) E01 (E13 7)WWBIdling9 to 14W (E9±11) ± E01 (E13±7)W ± W±BIG switch ONBelow 3.0
ELS (E9 12) E1 (E11 1)GBRTaillight switch ON, Defogger switch ON7.5 to 14ELS (E9±12) ± E1 (E11±1)G ± BRTaillight switch OFF, Defogger switch OFF0 to 1.5
TACH (E9±5) ± E1 (E11±1)GR±R ± BRIdlingPulse generation
SPD (E10±17) ± E01 (E13±7)V±W ± W±BIG switch ON4.5 to 5.5
TC (E9±20) ± E1 (E11±1)W±L ± BRIG switch ON9 to 14
SIL (E9±18) ± E1 (E11±1)W±G ± BRDuring charge of gearsPulse generation
PSW (E11±10) ± E1 (E11±1)G ± BRWhile turning the steering wheelBelow 1.5
F/PS (E9±14) ± E1 (E11±1)LG±B ± BRIG switch ONBelow 1.5

A76874
C1
Camshaft Position Sensor
C6
Crankshaft Position SensorR W
2 1
EE BR
G J12
J/CE1127ECM
G2+
NE+
NE± (Shielded)
R
BRE11
E1125
24
2 1
(Shielded)E E
E
R R
Crankshaft
Position
Sensor
Plate No. 1Camshaft
Timing
Pulley LH
A64984Crankshaft Position Sensor Component Side
C6
05±434
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

Perform troubleshooting of DTC P0335 first. If no trouble is found, troubleshoot the engine mechanical
system.

Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle
was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc. at
the time of the malfunction.
1 INSPECT CRANKSHAFT POSITION SENSOR(RESISTANCE)
(a) Disconnect the C6 crankshaft position sensor connector.
(b) Measure the resistance between the terminals of the
crankshaft position sensor.
Resistance:
985 to 1,600 at cold
1,265 to 1,890 at hot
NOTICE:
ºColdº and ºHotº shown above mean the temperature of
the coils themselves. ºColdº is from ±10C (14F) to 50C
(122F) and ºHotº is from 50C (122F) to 100C (212F).
NG REPLACE CRANKSHAFT POSITION SENSOR
OK

A76872
K1
Knock SensorECM
KNK1
E12
(Shielded)
1 BR D
E
J13 J12 1
B B
J/C EKNK
E12 2
W
2
EEJ12
J13
D
E
BR BR 5 V
05±430
±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, it is useful for determi\
ning whether the vehicle was running
or stopped, the engine was warmed up or not, the air±fuel ratio was lea\
n or rich, etc. at the time of the mal-
function.
1READ OUTPUT DTC
(a)Clear the DTC (See page 05±294).
(b) Warm up the engine.
(c) Run the engine at 3,000 rpm for 10 seconds or more.
(d)Read the DTC (See page 05±294). Result :
Display (DTC output)Proceed to
Only ºP0325º is output againA
ºP0325, P0327 and/or P0328º are output againB
ºP0325, P0327 and/or P0328º are not output againC
B Go to step 3
C CHECK FOR INTERMITTENT PROBLEMS
A

A76865
ECM
+B 1
E9
W±B 4
2
1
2
12
4A
W±B
Battery
EC 1 3
5
FL MAINB±R
EE (Shielded) 4EFI
No. 1Engine
Room
R/B No. 4
B±W
B±R
Engine Room
R/B No. 4 EFI
Relay
B±Y 44
44
1
4B 1Engine Room
J/B No. 4 B±G
B±GEFI 1
1A 1Engine
Room
R/B No. 1
and
Engine
Room
J/B No. 1GRB±R B±R
B±YB±YB±YGRGR B±R
+B2 2
E9 D
J14
(LHD)(RHD)D
J28D
J14
(LHD)(RHD)D
J28
D
J14D
J28 J/C
B±R 2
IE4
(LHD) (RHD)3
IP1
7
IE3
(LHD) (RHD)7
IO12
IE1
B±YMREL 8
E9
BATT 3
E9
4 IE2V
IREL 35
E10 V
21 5
3INJ
Relay 44
44
R±B
IJF1 25
E13
G±W
#1 1
E13 5
E5
4
E5 IJF
IJT#1
W±R
#2 2
E13 1
E5 IJT#2
R±W
#3 3
E13 2
E5 IJT#3
W±L
#4 4
E13 3
E5 IJT#4
Electronic
Driver Unit
EA1 7Y4
E4 INJ#1
1
2 I 5
Injector No. 1
BR
B±R 3
E4 INJ#4
1
2 I 8
Injector No. 4
BR
BR 5
E4
COM1
P 1
E4 INJ#2
1
2 I 6
Injector No. 2
L
B±W 2
E4 INJ#3
1
2 I 7
Injector No. 3
L
L 6
E4 COM2 B
B (Shielded)
8
E4VB
W7
E4 GND
W±B
EF BR BR 05±416
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
WIRING DIAGRAM

±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
05±411
AVENSIS REPAIR MANUAL (RM1018E)
WIRING DIAGRAM
Refer to DTC P1235 on page 05±477.
INSPECTION PROCEDURE
HINT:

If different DTCs related to different systems that have terminal E2 as the ground terminal are output
simultaneously, terminal E2 may be open.

Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, it is useful for deter\
mining whether the vehicle
was running or stopped, the engine was warmed up or not, the air±fuel ra\
tio was lean or rich, etc. at
the time of the malfunction.
1CHECK OTHER DTC OUTPUT(IN ADDITION TO DTC P0191)
(a)Read the DTC using the hand±held tester.
Result:
Display (DTC output)Proceed to
Only ºP0191º is outputA
ºP0191º and other DTCs are outputB
HINT:
If any other codes besides ºP0191º are output, perform the troublesh\
ooting for those DTCs first.
BGO TO RELEVANT DTC CHART(See page 05±309)
A
2READ VALUE OF HAND±HELD TESTER(FUEL PRESSURE)
(a)Connect the hand±held tester to the DLC3.
(b)Start the engine.
(c)Push the hand±held tester main switch ON.
(d)Select the item ºDIAGNOSIS / OBD/MOBD / DATA LIST / ALL / FUEL PRESSº and read its value dis- played on the hand±held tester.
Pressure: 8 to 13 MPa (81.6 to 132.6 kgf/cm
2, 1,160 to 1,885 psi)
NGGo to step 10
OK
3CHECK FUEL PRESSURE(LOW PRESSURE) (See page 11±33)
NG Go to step 12
OK
4 CHECK FOR FUEL LEAKS(HIGH PRESSURE)
(a) Check if there is leakage in the fuel pipe located between the high±pressure fuel pump and the injec- tors.

A14687
(V)
4.5
0.5
(0)019.6
(200)MPa
(kgf/cm2)
Output Voltage
Fuel Pressure
A00309
F16
Fuel Pressure Sensor
18
E13ECM
5V
E1 1 R±W
23
Y±G 2
3
BR28
E2 PRVC
VOUT
GNDE13
E13 VCC 05±406
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
DTC P0190 FUEL RAIL PRESSURE SENSOR CIRCUIT
CIRCUIT DESCRIPTION
The fuel pressure sensor is installed on a fuel delivery pipe and
detects the fuel pressure. It controls of feedback the pump dis-
charge in order to keep the fuel at target pressure 8 to 13 MPa
(81.6 to 132.6 kgf/cm
2, 1,160 to 1,885 psi) by the ECM.
DTC No.DTC Detection ConditionTrouble Area
P0190Open or short in fuel pressure sensor circuit

Open or short in fuel pressure sensor circuit

Fuel pressure sensor

ECM
HINT:
After confirming DTC ºP0190º, use the hand±held tester to confirm the delivery pipe pressure from ºDIAG-
NOSIS / OBD/MOBD / DATA LIST / ALLº.
Fuel Pressure (MPa)Malfunction
Approximately 0
PR circuit short
19.6 or more

VC circuit open or short

PR circuit open

E2 circuit open
WIRING DIAGRAM
05CKE±01

±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
05±395
AVENSIS REPAIR MANUAL (RM1018E)

If the total of the short±term fuel trim value and long±term fuel tri\
m value is within
25 % (Engine cool-
ant temperature is greater than 75 C), the system is functioning normally.

Bank 1 refers to the No. 1 and No. 4 cylinders.

Bank 2 refers to the No. 2 and No. 3 cylinders.
WIRING DIAGRAM
Refer to DTC P0130 on page 05±363.
INSPECTION PROCEDURE
HINT:
Hand±held tester only:
Narrowing down the trouble area is possible by performing the ºA/F CONTROLº ACTIVE TEST (heated oxy-
gen sensor or other trouble areas can be distinguished).
(a) Perform ACTIVE TEST using the hand±held tester (A/F CONTROL).
HINT:
ºA/F CONTROLº is an ACTIVE TEST which changes the injection volume\
±12.5 % or +25 %.
(1) Connect the hand±held tester to the DLC3 on the vehicle.
(2) Turn the ignition switch ON.
(3) Warm up the engine by running the engine at 2,500 rpm for approximately 9\
0 sec.
(4) Select the item ºDIAGNOSIS / OBD/MOBD / ACTIVE TEST / A/F CONTROLº\
.
(5) Perform ºA/F CONTROLº with the engine in an idle condition (press\
the right or left button).
Result:
Heated oxygen sensor reacts in accordance with increase and decrease of injection volume:
+25 %
rich output: More than 0.55 V
±12.5 %
lean output: Less than 0.4 V
NOTICE:
There is a few seconds delay in the sensor 1 (front sensor) output. And there is about 20 seconds
delay in the sensor 2 (rear sensor).




3020
10
5
3
02040
0.1 1
0.3 0.2
0.5 2
6080100
±20
(±4)(104)(140)(176) (32)(68)(212)


30
20
10
5
3
02040
0.1 1
0.3 0.2
0.5 2
6080100
±20
(±4)(104)(140)(176) (32)(68)(212)
A81700
Ohmmeter
Acceptable
TEMPERATURE
C (
F)
RESISTANCE K 
±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
05±399
AVENSIS REPAIR MANUAL (RM1018E)
5INSPECT ENGINE COOLANT TEMPERATURE SENSOR(RESISTANCE)
(a)Remove the engine coolant temperature sensor.
(b)Measure the resistance between the terminals.
Resistance:
2.32 to 2.59 k at 20
C (68
F)
0.310 to 0.326 k at 80
C (176
F)
NOTICE:
In case of checking the engine coolant temperature sensor
in the water, be careful not to allow water to go into the ter-
minals. After checking, dry the sensor.
HINT:
Alternate procedure: Connect an ohmmeter to the installed en-
gine coolant temperature sensor and read the resistance. Use
an infrared thermometer to measure the engine temperature in
the immediate vicinity of the sensor. Compare these values to
the resistance/temperature graph. Change the engine temper-
ature (warm up or allow to cool down) and repeat the test.
NGREPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK
6CHECK FOR SPARK AND IGNITION (See page 18±12)
NG REPAIR OR REPLACE
OK
7CHECK FUEL PRESSURE(LOW PRESSURE) (See page 11±33)
NG CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND
FILTER
OK
8CHECK FUEL PRESSURE(HIGH PRESSURE) (See page 11±33)
NG CHECK AND REPLACE FUEL PUMP, FUEL PRESSURE SENSOR, WIRING AND FUEL
LEAKAGE
OK