2005 TOYOTA AVENSIS fuel

B62793
Reference:
A/F Sensor A/F Sensor
Heater Relay
Heater
Sensor
AF2+ HAF2
Duty
Control ECM
From
Battery
A/F Fuse
AF2−
MREL 05−306
− DIAGNOSTICSECD SYSTEM (1CD−FTV)(From September, 2003)
AVENSIS Supplement (RM1045E)
HINT:
The ECM provides a pulse width modulated control circuit to adjust current through the heater. The A/F sen-
sor heater circuit uses a relay on the B+ side of the circuit.
DTC No.DTC Detection ConditionTrouble Area
P0031Heated current is 1.5 A or less when the heater operates
(1 trip detection logic)
SOpen in A/F sensor heater circuit
SA/F sensor heater
SA/F sensor heater relay
SECM
MONITOR DESCRIPTION
The inner surface of the A/F sensor element is exposed to outside air. The outer surface of the sensor ele-
ment is exposed to exhaust gases. The sensor element is made of platinum coated zirconia and includes
an integrated heating element. The zirconia element generates small voltage when there is a large differ-
ence in the oxygen concentrations of the exhaust and the outside air. The platinum coating amplifies the
voltage generation. When heated, the sensor becomes very efficient. If the temperature of the exhaust is
low, the sensor will not generate useful voltage signals without supplemental heating. The ECM regulates
the supplemental heating using a duty−cycle approach to regulate the average current in the heater ele-
ment. If the heater current is out of the normal range, the sensor’s output signals will be inaccurate and the
ECM can not regulate the air−fuel ratio properly. When the heater current is out of the normal operating
range, the ECM interprets this as a malfunction and sets a DTC.

A87894
AF−AF+
A34
Front View Component Side
(w/ Headlight Beam Level Control):
1 2
3 4
HT
+B
A/F Sensor
Connector
A87894
AF− AF+
A34
Front View
HT +B
1 2
3 4 Component Side
(w/o Headlight Beam Level Control):
A/F Sensor
Connector
B16200
05−308
− DIAGNOSTICSECD SYSTEM (1CD−FTV)(From September, 2003)
AVENSIS Supplement (RM1045E)
INSPECTION PROCEDURE
1INSPECT AIR FUEL RATIO SENSOR(RESISTANCE)
(a) Disconnect the A34 A/F sensor connector.
(b) Measure the resistance between the terminals of the A/F
sensor.
Resistance (w/ Headlight beam level control):
Tester ConnectionSpecified Condition
HT (1)−+B (2)0.86 to 1.1
at 20_C (68_F)
Resistance (w/o Headlight beam level control):
Tester ConnectionSpecified Condition
HT (2)−+B (1)0.86 to 1.1
at 20_C (68_F)
(c) Reconnect the A/F sensor connector.
NG REPLACE AIR FUEL RATIO SENSOR
OK
2 INSPECT AIR FUEL RATIO SENSOR HEATER RELAY
(a) Remove the A/F sensor heater relay.
(b) Inspect the A/F sensor heater relay.
Standard:
Tester ConnectionSpecified Condition
1−2Continuity
No continuity
3−5Continuity
(Apply battery voltage to terminals 1 and 2)
(c) Reinstall the A/F sensor heater relay.
NG REPLACE AIR FUEL RATIO SENSOR HEATER
RELAY
OK

054JD−11
−
DIAGNOSTICS ECD SYSTEM (1CD −FTV)(From September, 2003)
05 −299
AVENSIS Supplement (RM 1045E)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may be different than your readings depending on the type of instrument used
and other factors.
During the DTC check, refer to the table below if a malfunction code is displayed. For details about each
code, refer to the page number in the DTC Chart’s left column.
DTC No.
(See Page)Detection ItemTrouble Area* 1
CHK ENGMemory
P003 1
(05 −305)Oxygen (A/F) Sensor Heater
Control Circuit Low (Bank 1Sen-
sor 1)SOpen in A/F sensor heater circuit
S A/F sensor heater
S A/F sensor heater relay
S ECM
ff
P0045
(05 −312)Turbo/Super Charger Boost Con-
trol Solenoid Circuit / OpenSVRV
S Open or short in VRV circuit
S ECM
ff
P0087
(05 −314)Fuel Rail/System Pressure −To o
LowS Open or short in fuel pressure sensor circuit
S Fuel pressure sensor
S ECM
ff
P0088
(05 −32 1)Fuel Rail/System Pressure −To o
High
S Supply pump (Suction control valve)
S Pressure discharge valve
S Short in supply pump (Suction control valve) circuit
S Open in pressure discharge valve circuit
S ECM
ff
P0093
(05 −328)Fuel System Leak Detected −
Large Leak
S Fuel line between supply pump and common rail
S Fuel line between common rail and injector
S Supply pump
S Common rail
S Injector (P 1238 is set simultaneously)
S Pressure discharge valve
S Open or short in EDU circuit (P0200 is set simultaneously)
S Open or short in injector circuit (P0200 and P 1238 are set
simultaneously)
S EDU (P0200 is set simultaneously)
S ECM
ff
P0095
(05 −33 1)Intake Air Temperature Sensor 2
Circuit
S Open or short in diesel turbo inlet air temperature sensor cir-ff
P0097
(05 −33 1)Intake Air Temperature Sensor 2
Circuit Low
SOpenorshortindieselturboinletairtemperaturesensorcir-
cuit
S Diesel turbo inlet air temperature sensor
ff
P0098
(05 −33 1)Intake Air Temperature Sensor 2
Circuit High
p
S ECMff
P0 100
(05 −336)Mass or Volume Air Flow Circuit
SOpen or short in mass air flow meter circuit
S Mass air flow meter
S ECM
ff
P0 101
(05 −34 1)Mass or Volume Air Flow Circuit
Range/Performance ProblemS Mass air flow meterff
P0 102
(05 −336)Mass or Volume Air Flow Meter
Circuit Low InputSOpen or short in mass air flow meter circuit
SMassairflowmeter
ff
P0 103
(05 −336)Mass or Volume Air Flow Meter
Circuit High InputSMass air flow meter
S ECM
ff
P0 105
(05 −342)Manifold Absolute Pressure/
Barometric Pressure Circuit
SOpen or short in manifold absolute pressure sensor circuit
S Manifold absolute pressure sensor
S Turbocharger assembly
S EGR valve assembly
S ECM
ff
P0 106
(05 −346)Manifold Absolute Pressure/
Barometric Pressure Circuit
Range/Performance Problem
SManifold absolute pressure sensorff

05−300
−
DIAGNOSTICS ECD SYSTEM (1CD −FTV)(From September, 2003)
AVENSIS Supplement (RM 1045E)
DTC No.
(See Page) Memory
*
1
CHK ENG
Trouble Area
Detection Item
P0 107
(05 −342)Manifold Absolute Pressure/
Barometric Pressure Circuit Low
InputSOpen or short in manifold absolute pressure sensor circuit
S Manifold absolute pressure sensor
Turbochargerassy
ff
P0 108
(05 −342)Manifold Absolute Pressure/
Barometric Pressure Circuit High
InputSTurbochargerassy
S EGR valve assy
S ECM
ff
P0 110
(05 −347)Intake Air Temperature Circuit
Ohtiitkittiit
ff
P0 112
(05 −347)Intake Air Temperature Circuit
Low InputSOpen or short in intake air temperature sensor circuit
S Intake air temperature sensor (built in mass air flow meter)
SECM
ff
P0 113
(05 −347)Intake Air Temperature Circuit
High InputSECM
ff
P0 115
(05 −352)Engine Coolant Temperature Cir-
cuitSOpen or short in engine coolant temperature sensor circuit
S Engine coolant temperature sensor
S ECM
ff
P0 116
(05 −356)Engine Coolant Temperature Cir-
cuit Range/Performance Prob-
lem
SEngine coolant temperature sensorff
P0 117
(05 −352)Engine Coolant temperature Cir-
cuit Low InputSOpen or short in engine coolant temperature sensor circuit
SEnginecoolanttemperaturesensor
ff
P0 118
(05 −352)Engine Coolant temperature Cir-
cuit High InputSEngine coolant temperature sensor
S ECM
ff
P0 120
(05 −357)Throttle/Pedal Position Sensor/
Switch ”A” Circuit
SOpen or short in intake shutter (throttle valve) position sensor
circuit
S Intake shutter (throttle valve) position sensor
S ECM
ff
P0 122
(05 −357)Throttle/Pedal Position Sensor/
Switch ”A” Circuit Low Input
SIntake shutter (throttle valve) position sensor
S Open or short in VLU circuit
S Open in VC circuit
S ECM
ff
P0 123
(05 −357)Throttle/Pedal Position Sensor/
Switch ”A” Circuit High Input
SIntake shutter (throttle valve) position sensor
S Open in E2 circuit
S VC and VTA circuits are short −circuited
S ECM
ff
P0 168
(05 −36 1)Fuel Temperature Too HighS Fuel temperature sensorff
P0 180
(05 −362)Fuel Temperature Sensor ”A”
Circuit
Openorshortinfueltemperaturesensorcircuit
ff
P0 182
(05 −362)Fuel Temperature Sensor ”A”
Circuit Low InputSOpen or short infuel temperature sensor circuit
S Fuel temperature sensor
SECM
ff
P0 183
(05 −362)Fuel Temperature Sensor ”A”
Circuit High InputSECM
ff
P0 190
(05 −314)Fuel Rail Pressure Sensor Cir-
cuitSOpen or short in fuel pressure sensor circuit
S Fuel pressure sensor
S ECM
ff
P0 191
(05 −367)Fuel Rail Pressure Sensor Cir-
cuit Range/PerformanceSFuel pressure sensorff
P0 192
(05 −314)Fuel Rail Pressure Sensor Cir-
cuit Low InputSOpen or short in fuel pressure sensor circuit
SFuelpressuresensor
ff
P0 193
(05 −314)Fuel Rail Pressure Sensor Cir-
cuit High InputSFuel pressure sensor
S ECM
ff
P0200
(05 −368)Injector Circuit / Open
SOpen or short in EDU circuit
S Injector
S EDU
S ECM
ff

05−302
−
DIAGNOSTICS ECD SYSTEM (1CD −FTV)(From September, 2003)
AVENSIS Supplement (RM 1045E)
DTC No.
(See Page) Memory
*
1
CHK ENG
Trouble Area
Detection Item
P0606
(05 −425)ECM/PCM Processor
ECM



P0607
(05 −425)Control Module Performance
SECM
ff
P0622
(05 −426)Generator Field ”F” Terminal Cir-
cuit
SOpen in generator (alternator) circuit
S Generator (alternator)
S Drive belt
S ECM
ff
P0627
(05 −429)Fuel Pump Control Circuit / Open
SOpen or shot in suction control valve circuit
S Suction control valve
S ECM
ff
P 1229
(05 −32 1)Fuel Pump System
S Short in supply pump (suction control valve) circuit
S Supply pump (suction control valve)
S ECM
ff
P 1238
(05 −43 1)Injector Malfunction
S Injector
S EDU (P0200 is set simultaneously)
S Open or short in engine wire harness (P0200 is set simulta-
neously)
S Connector connection (P0200 is set simultaneously)
S Compression pressure
S Valve clearance
S Valve timing
S ECM
ff
P 125 1
(05 −376)Turbo/Super Charger Overboost
Condition (Too High)
SVRV
S Open or short in VRV circuit
S Turbocharger
S EGR valve
S Vacuum hose
S ECM
ff
P 127 1
(05 −435)Fuel Regulator Circuit Malfunc-
tion (EDU Drive)
SOpen or short in pressure discharge valve circuit
S Open or short in pressure discharge valve itself
S EDU
S ECM
ff
P 1272
(05 −435)Fuel Pressure Regulator Mal-
function
SOpen or short in pressure discharge valve circuit (P 127 1is set
simultaneously)
S Pressure discharge valve
S Supply pump
S ECM
ff
P 1386
(05 −444)Injector For Exhaust Fuel Addi-
tion
SOpen or short in exhaust fuel addition injector circuit
S Exhaust fuel addition injector
S DPNR catalytic converter (Manifold converter sub −assy)
S Open in exhaust temperature sensor circuit
S A/F sensor
S Exhaust gas temperature sensor
S Supply pump assy
S Mass air flow meter
S Fuel leaks in exhaust fuel addition injector
S Main injector
S Cylinder compression pressure
S Valve clearance
S Valve timing
S Air intake system has blockages
S Air intake system has leakage
S Exhaust system has blockages
S Exhaust system has leakage
S EGR system has blockages
S EGR system has leakage
S ECM
ff

−
DIAGNOSTICS ECD SYSTEM (1CD −FTV)(From September, 2003)
05 −303
AVENSIS Supplement (RM 1045E)
DTC No.
(See Page) Memory
*
1
CHK ENG
Trouble Area
Detection Item
P 1425
(05 −457)Differential Pressure Sensor Cir-
cuit
SOpen or short in differential pressure sensor circuit
S Incorrect arrangement differential pressure sensor hose piping
S Differential pressure sensor
S ECM
ff
P 1426
(05 −462)Differential Pressure Sensor
(Installation)
SIncorrect arrangement differential pressure sensor hose piping
S Differential pressure sensor vacuum hose is clogged
S Blockage in vacuum transmitting pipe sub −assy
S Differential pressure sensor
S ECM
ff
P 1427
(05 −457)Differential Pressure Sensor Cir-
cuit LowSOpen or short in differential pressure sensor circuit
S Incorrect arrangement differential pressure sensor hose pipingff
P 1428
(05 −457)Differential Pressure Sensor Cir-
cuit High
Incorrectarrangementdifferentialpressuresensorhosepiping
SDifferential pressure sensor
S ECMff
P 160 1
(05 −465)Injector Correction Circuit Mal-
function (EEPROM)SInjector compensation code
S ECMff
P 1611
(05 −425)IC Circuit MalfunctionSECMff
P2002
(05 −466)Particulate Trap Efficiency Below
Threshold (Bank 1)
SDPNR catalytic converter (manifold converter sub −assy)
S Differential pressure sensor
S Differential pressure sensor vacuum hose is clogged
S Blockage in vacuum transmitting pipe sub −assy
S Exhaust gas temperature sensor
S Exhaust gas leaks in TOYOTA D −CAT
S Mass air flow meter
S ECM
ff
P203 1
(05 −415)Exhaust Gas Temperature Sen-
sor Circuit (Bank 1Sensor 2)ff
P2032
(05 −415)Exhaust Gas Temperature Sen-
sor Circuit Low (Bank 1Sensor
2)S Open or short in exhaust gas temperature sensor (on down
stream) circuit
S Exhaust gas temperature sensor (on down stream)
ff
P2033
(05 −415)Exhaust Gas Temperature Sen-
sor Circuit High (Bank 1Sensor
2)
gp()
S ECM
ff
P2047
(05 −470)Reductant Injector Circuit/Open
(Bank 1Unit 1)SOpen in exhaust fuel addition injector circuit
S Exhaust fuel addition injector
S ECM
ff
P2 120
(05 −473)Throttle/Pedal Position Sensor/
Switch ”D” CircuitSOpen or short in accelerator pedal position sensor circuit
S Accelerator pedal position sensor
S ECM
ff
P2 121
(05 −479)Throttle/Pedal Position Sensor/
Switch ”D” Circuit Range/Perfor-
manceSAccelerator pedal position sensor circuit
S Accelerator pedal position sensor
S ECM
ff
P2 122
(05 −473)Throttle/Pedal Position Sensor/
Switch ”D” Circuit Low Inputff
P2 123
(05 −473)Throttle/Pedal Position Sensor/
Switch ”D” Circuit High Inputff
P2 125
(05 −473)Throttle/Pedal Position Sensor/
Switch ”E” Circuit
SOpen or short in acceleratorpedalposition sensor circuitff
P2 127
(05 −473)Throttle/Pedal Position Sensor/
Switch ”E” Circuit Low Input
SOpenorshortinacceleratorpedalpositionsensorcircuit
SAccelerator pedal position sensor
S ECMff
P2 128
(05 −473)Throttle/Pedal Position Sensor/
Switch ”E” Circuit High Inputff
P2 138
(05 −473)Throttle/Pedal Position Sensor/
Switch ”D”/”E” Voltage Correla-
tion
ff

05DVU−02
− DIAGNOSTICSECD SYSTEM (1CD−FTV)(From September, 2003)
05−295
AVENSIS Supplement (RM1045E)
DATA LIST/ACTIVE TEST
1. DATA LIST
HINT:
Using the hand−held tester DATA LIST allows switch, sensor, actuator and other item values to be read with-
out removing any parts. Reading DATA LIST early in troubleshooting is one way to shorten labor time.
NOTICE:
In the table below, the values listed under ”Normal Condition” are reference values. Do not depend
solely on these reference values when deciding whether a part is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch to OFF.
(c) Connect the hand−held tester to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the hand−held tester ON.
(f) Enter the following menus: DIAGNOSIS / OBD/MOBD / DATA LIST.
(g) According to the display on the tester, read DATA LIST.
Hand−held Tester DisplayMeasurement Item/Range
(Display)Normal Condition *Diagnostic Note
INJ VOLUMEInjection volume/
Min.: 0 mm3, Max.:1279.98 mm3Idling: 3 to10mm3

ENGINE SPDEngine speed/
Min.: 0 rpm, Max.:16383.75 rpmIdling: 750 to850rpm

MAF
Air flow rate from MAF meter sta-
tus/
Min.: 0 gm/s, Max.: 655.35 gm/sSIdling: 3.2 to 4.7 gm/s
SRunning without load (2,500
rpm):13.1to18.9 gm/s
If the value is approximately 0.0
gm/s:
SMass air flow meter power
source circuit open
SVG circuit open or short
If the valve is160 gm/s or more:
SE2G circuit open
PIM
Absolute pressure inside intake
manifold/
Min.: 0 kPa, Max.: 224 kPaIgnition switch ON:
Same as atmospheric pressureEngine is not running
COOLANT TEMPCoolant temperature/
Min.:−40_C, Max.: 215_CAfter warming up: 75 to 95˚C(167
to 203˚F)
INTAKE AIRIntake air temperature/
Min.:−40_C, Max.: 215_CEquivalent to air temperature at
the intake manifoldIf the value is ”−40_C” or ”140_C
or more”, sensor circuit is open or
shorted
FUEL TEMPFuel temperature status/
Min.:−40_C, Max.: 215_CActual fuel temperature
shorted
ACCEL POSITIONAccel position status/
Min.: 0 %, Max.:100 %
SAccelerator pedal released:
10to22%
SAccelerator pedal depressed:
52 to 90 %
Read the value with ignition switch
ON (Do not start engine)
VEHICLE SPDVehicle speed/
Min.: 0 km/h, Max.: 255 km/hActual vehicle speedSpeed indicated on speedometer
THROTTLE POSThrottle position sensor status/
Min.: 0 %, Max.:100 %SThrottle fully closed: 98 %
SThrottle fully open: 0 %100 % when the engine is at rest
COMN RAILCommon rail pressure status/
Min.: 0 MPa, Max.: 255 MPaSIdling: 30 to 40 MPa
SEngine running at 3,000 rpm:
50 to100 MPa


AMBI TEMP SENS
Ambient temperature sensor sta-
tus/
Min.:−40_C, Max.: 215_CActual atmospheric air tempera-
tureIf the value is ”−40_C” or ”140_C
or more”, sensor circuit is open or
shorted

05−296
− DIAGNOSTICSECD SYSTEM (1CD−FTV)(From September, 2003)
AVENSIS Supplement (RM1045E) Hand−held Tester DisplayDiagnostic Note Normal Condition * Measurement Item/Range
(Display)
INJ VOL FB #1
Injection volume correction for cyl-
inder1/
Min.:−10mm
3, Max.:10mm3Idling:−3.0 to 3.0 mm3

INJ VOL FB #2
Injection volume correction for cyl-
inder 2/
Min.:−10mm
3, Max.:10mm3Idling:−3.0 to 3.0 mm3

INJ VOL FB #3
Injection volume correction for cyl-
inder 3/
Min.:−10mm
3, Max.:10mm3Idling:−3.0 to 3.0 mm3

INJ VOL FB #4
Injection volume correction for cyl-
inder 4/
Min.:−10mm
3, Max.:10mm3Idling:−3.0 to 3.0 mm3

M−INJ/PILOT ON
Pilot−injection ON timing of main
injector/
Min.: 0s Max.: 65,535s
Idling: 600 to1,200s

M−INJ/PILOT OFF
Pilot−injection OFF timing of main
injector/
Min.: 0s Max.: 65,535s
Idling: 600 to1,200s

PILOT−INJPilot−injection/
Min.: 0s, Max.: 65,535sIdling: 400 to 700s

INJ FB VALUE
Injection volume feedback learning
value/
Min.:−10mm
3, Max.: 9,092 mm3Idling:−4.0 to 4.0 mm3

STOP LIGHT SWStop lamp switch/
ON or OFFSBrake pedal depressed: ON
SBrake pedal released: OFF

STARTER SIGStarter signal/ ON or OFFCranking: ON

CHECK MODECheck mode/ ON or OFFCheck mode ON: ON

EGR VALVE POSEGR position sensor status/
Min.: 0 V, Max.: 5 VSClosed: 4.0 V
SOpen: 2.1V

MIL ON RUN DIST
Travel distance after check engine
warning light (CHK ENG) was illu-
minated/
Min.: 0 km, Max.: 65,535 kmActual travel distance after check
engine warning light was illumi-
nated


AFS B1S1
A/F sensor output voltage for bank
1sensor1/
Min.: 0 V, Max.: 7.999 V
Idling 2.8 to 3.8 V

DPNR DIFF PRESSDPNR differential pressure/
Min.:−5 kPa, Max.:100 kPaIdling: approximately 0 kPa

GENERATOR
Generator (alternator) duty ratio
status/
Min.: 0 %, Max.:100 %
Idling:10to100 %

EX TEMP INExhaust gas temperature for IN/
Min.: 0_C, Max.:1000_CActual exhaust gas temperature
(on up stream)

EX TEMP OUTExhaust gas temperature for OUT/
Min.: 0_C, Max.:1000_CActual exhaust gas temperature
(on down stream)

EX FUEL ADD FB
Exhaust fuel addition correction
value/
Min.: 0, Max.: 2
Vicinity of1.0

AF FT B1S1
Short−term fuel trim associated
with the bank1sensor1/
Min.: 0, Max.:1.999
SValue less than1(0.000 to
0.999) = Correction to lean
SStoichiometric Air−fuel ratio=1
SValue greater than1(1.001to
1.999) = Correction to rich