2005 TOYOTA AVENSIS wiring

A93655
17
E10SPDECM
V–W 18
C11 Combination Meter
J/C
5
E13 E15 V
BR
EHJ10H
V–W
(LHD) J20H
(RHD)J10H
(LHD) J20H
(RHD)
– DIAGNOSTICSSFI SYSTEM (1ZZ–FE/3ZZ–FE)(From February, 2004)
05–159
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the intelligent tester II. Freeze frame data record the engine condition when
malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was
moving or stationary, if the engine was warmed up or not, if the air–fuel ratio was lean or rich, and other data
from the time the malfunction occurred.
1 CHECK OPERATION OF SPEEDOMETER
(a) Drive the vehicle and check if the operation of the speedometer in the combination meter is normal.
HINT:
The vehicle speed sensor is operating normally if the speedometer reading is normal.
NG CHECK SPEEDOMETER CIRCUIT
(See page 05–1510 of Pub. No. RM1018E AVEN-
SIS)
OK

A96006
2
EFI
1 1
FL MAINW–BEFI Relay
1 43 5
2
EA1
B–W
V5
EVAP VSV
219
E12
MREL 4
E10 44
44
42 1
B–W
W–G 1 IE1 2
GR13
EC 1 1A
4A
4B1
1
B–G
BatteryB–W
EFI
No. 2 B–Y
B–G
EVP1ECM
Engine
Room
R/B No.1Engine
Room
R/B No.4 Engine Room R/B No.4
GR
– DIAGNOSTICSSFI SYSTEM (1ZZ–FE/3ZZ–FE)(From February, 2004)
05–155
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
DTC P0443 EVAPORATIVE EMISSION CONTROL
SYSTEM PURGE CONTROL VALVE CIRCUIT
CIRCUIT DESCRIPTION
In order to reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through the char-
coal canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signal to the EVAP VSV so that the intake of HC emissions is appropriate for
the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.
DTC No.DTC Detection ConditionTrouble Area
P0443Proper response to ECM command does not occur (1 trip
detection logic)Open or short in EVAP VSV circuit
EVAP VSV
ECM
WIRING DIAGRAM
05KO8–02

05–152
–
DIAGNOSTICS SFI SYSTEM (1ZZ–FE/3ZZ–FE)(From February, 2004)
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
NOTICE:
If the conditions in this test are not strictly followed, no malfunction\
will be detected. If you do not
have the intelligent tester II, turn the ignition switch to OFF after perfor\
ming steps from (d) to (i), then
perform steps (d) to (i) again.
WIRING DIAGRAM
Refer to DTC P0130 on page 05–74.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the intelligent tester II. Freeze frame data record the engine condition\
when
malfunctions are detected. When troubleshooting, freeze frame data can h\
elp determine if the vehicle was
moving or stationary, if the engine was warmed up or not, if the air–fuel ratio was lean \
or rich, and other data
from the time the malfunction occurred.
1 CHECK OTHER DTC OUTPUT(IN ADDITION TO DTC P0420)
(a) Connect the intelligent tester II to the DLC3.
(b) Turn the ignition switch to ON and turn the intelligent tester ll ON.
(c) Select the following menu items: Powertrain / Engine and ECT / DTC.
(d) Read DTCs.
Result:
Display (DTC Output)Proceed To
P0420A
P0420 and other DTCsB
HINT:
If any DTCs other than P0420 are output, troubleshoot those DTCs first.
B GO TO RELEVANT DTC CHART (See page 05–27 )
A
2 CHECK FOR EXHAUST GAS LEAKAGE
OK: No gas leakage. NG REPAIR OR REPLACE EXHAUST GASLEAKAGE POINT
OK
3 INSPECT HEATED OXYGEN SENSOR(SENSOR 1) ( See page 05–74)
NG REPLACE HEATED OXYGEN SENSOR
OK

A63955
GND
CH1
(G2+)
CH2
(NE+) GND
05–140
–
DIAGNOSTICS SFI SYSTEM (1ZZ–FE/3ZZ–FE)(From February, 2004)
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
DTC P0340 CAMSHAFT POSITION SENSOR ”A” CIRCUIT (BANK 1 OR SINGLE SENSOR)
DTC P0341 CAMSHAFT POSITION SENSOR ”A” CIRCUIT RANGE/PERFORMANCE (BANK 1
OR SINGLE SENSOR)
CIRCUIT DESCRIPTION
The Camshaft Position (CMP) sensor consists of a magnet and an iron core which is wrapped with coppe\
r
wire, and is installed on the cylinder head. When the camshaft rotates, each \
of 3 teeth on the camshaft
passes through the CMP sensor. This activates the internal magnet in the sensor, generating a voltage in
the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft
turns twice the voltage is generated 3 times in the CMP sensor. The generated voltage in the sensor acts
as a signal, allowing the ECM to locate the camshaft position. This signal is then used to con\
trol ignition tim-
ing, fuel injection timing, and the VVT system.
DTC No.DTC Detection ConditionTrouble Area
P0340
No camshaft position sensor signal to ECM during cranking
(2 trip detection logic)Open or short in camshaft position sensor circuit
 Camshaft position sensor
Camshaft timing pulleyP0340(2 trip detection logic)
No camshaft position sensor signal to ECM at engine speed
of 600 rpm or more (1 trip detection logic)Camshaft timing pulley
 Jumped tooth of timing chain
 ECM
P0341While crankshaft rotates twice, camshaft position sensor signal
is input to ECM 12 times or more (1 trip detection logic)
Open or short in camshaft position sensor circuit
 Camshaft position sensor
 Camshaft timing pulley
 Jumped tooth of timing chain
 ECM
HINT:
DTC P0340 indicates a malfunction related to the CMP sensor (+) circuit (the wi\
re harness between
the ECM and CMP sensor, and the CMP sensor itself).
DTC P0341 indicates a malfunction related to the CMP sensor (–) cir\
cuit (the wire harness between
the ECM and CMP sensor, and the CMP sensor itself).
Reference: Inspection using the oscilloscope.
HINT:
The correct waveform is as shown on the left.
G2+ stands for the camshaft position sensor signal, and
NE+ stands for the crankshaft position sensor signal.
ItemContents
TerminalCH1: G2+ – NE–
CH2: NE+ – NE–
Equipment Setting5V/Division, 20ms/Division
ConditionDuring cranking or idling
WIRING DIAGRAM
Refer to DTC P0335 on page 05–136.
05B5J–14

A96003
K1
Knock Sensor1 (Shielded)
J/C J5
J51
E12 ECM
KNK1
EH
2
E122
EKNK
BB
J65 V
W
J6
EE D
EB1
EB1
2
1
D
BR BR
W
–
DIAGNOSTICS SFI SYSTEM (1ZZ–FE/3ZZ–FE)(From February, 2004)
05–133
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the intelligent tester II. Freeze frame data record the engine condition\
when
malfunctions are detected. When troubleshooting, freeze frame data can h\
elp determine if the vehicle was
moving or stationary, if the engine was warmed up or not, if the air–fuel ratio was lean \
or rich, and other data
from the time the malfunction occurred.
1 READ OUTPUT DTC
(a) Clear the DTC(s) ( see page 05–18).
(b) Warm up the engine.
(c) Run the engine at 3,000 rpm for 10 seconds or more.
(d) Connect the intelligent tester II to the DLC3.
(e) Turn the ignition switch to ON and turn the intelligent tester II ON.
(f) Select the following menu items: Powertrain / Engine and ECT / DTC.
(g) Read DTCs. Result :
Display (DTC Output)Proceed To
P0325A
P0325, and P0327 and/or P0328B
No outputC
B Go to step 3
C CHECK FOR INTERMITTENT PROBLEMS (See page 05–9 )
A

A76891
I13
Ignition Switch
4 6
B–R B–R
IE4 (LHD)
1
1 IP1
(RHD) DH
2
DL 16
Driver
Side J/B
IGN
B–R
1 AM2 IG2
1
2
2
1
1A1 1Engine
Room
R/B No.1
Engine
Room
J/B No.1
B–G
4A
1
4B1 Engine
Room
J/B No.4 B–R 2R–B 1
I5
Injector No.1
B–R
Y
W
B 1
#10
E13
2 #20
E13
#30
3
E13
4 #40
E13
7 E01
E13
E02
6
E13
W–B
W–B ECM
R–B R–B
R–B
R–B
R–B 21
I6
Injector No.2
21
I7
Injector No.3
21
I8
Injector No.4
EA18
4
13
25 IG2
Relay
B
W–B
B
EC EG
4
44 Engine
Room
R/B No.4
B–G
FL MAIN
Battery R–B
05–120
–
DIAGNOSTICS SFI SYSTEM (1ZZ–FE/3ZZ–FE)(From February, 2004)
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
WIRING DIAGRAM
Refer to DTC P0351 on page 05–143 for the wiring diagram of the ignition system.

05L2J–01
C95801
E13 E12 E10 E9
– DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U341E) (From February, 2004)05–233
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
TERMINALS OF ECM
1. ECM
HINT:
Each ECM terminal’s standard voltage is shown in the table below.
In the table, first follow the information under ”Condition”. Look under ”Symbols (Terminal No.)” for the termi-
nals to inspected. The standard voltage between the terminals is shown under ”Specific Condition”.
Use the illustration above as a reference for the ECM terminals.
Symbols (Terminals No.)Wiring ColorTerminal DescriptionConditionSpecified Condition
SLT+ (E12–13) –
SLT– (E12–12)P–L – PSLT solenoid signalEngine idle speedPulse generation
(See waveform 1)
THO (E12–32) – E2 (E13–28)V – BRATF temperature sensor
signalATF temperature: 115 C (239 F)
or moreBelow 1.5 V
ST (E12–20) – E1 (E13–5)R–B – BRST solenoid signalIG switch ONBelow 1 V
↑↑↑IG switch ON and R gear10 to 14 V
SL (E12–15) – E1 (E13–5)R – BRSL solenoid signalIG switch ONBelow 1 V
↑↑↑Vehicle driving under lock–up range10 to 14 V
S2 (E12–10) – E1 (E13–5)P – BRS2 solenoid signalIG switch ONBelow 1 V
↑↑↑1st or O/D gear10 to 14 V
↑↑↑2nd or 3rd gearBelow 1 V
S1 (E12–11) – E1 (E13–5)P–L – BRS1 solenoid signalIG switch ON10 to 14 V
↑↑↑1st or 2nd gear10 to 14 V
↑↑↑3rd or O/D gearBelow 1 V
SB (E12–8) – E1 (E13–5)L – BRSB solenoid signalIG switch ONBelow 1 V
NT+ (E12–26) – NT– (E12–34)B–O – BSpeed sensor (NT) signalVehicle speed 20 km/h (12 mph)Pulse generation
(See waveform 2)
SPT (E10–8) – E1 (E13–5)L – BRS shift position switch sig-
nalIG switch ON and shift lever S posi-
tion10 to 14 V
↑↑↑IG switch ON and shift lever except
S positionBelow 1 V
D (E10–10) – E1 (E13–5)LG–B – BRD shift position switch sig-
nalIG switch ON and shift lever D and
S position10 to 14 V
↑↑↑IG switch ON and shift lever except
D and S positionBelow 1 V
R (E10–11) – E1 (E13–5)R–Y – BRR shift position switch sig-
nalIG switch ON and shift lever R posi-
tion10 to 14 V
↑↑↑IG switch ON and shift lever except
R positionBelow 1 V

G25416
ECM
E10
K2
Kick Down SW
IP 6
6
CA 12
CJ
IG24
W–B Center J/B
31
8
IG2
W–B W
W
W–BKD *1
*1: LHD
G26420
Wire Harness Side:
(Connector Front View):
K2
–
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U341E) (From February, 2004)05–301
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
KICK–DOWN SWITCH CIRCUIT
CIRCUIT DESCRIPTION
The kick–down switch is turned ON when the accelerator pedal is fully de\
pressed and a signal is sent to the
ECM.
When the kick–down switch is turned ON, the ECM controls gear shiftin\
g according to the programmed shift
diagrams.
If a short circuit develops in the kick–down switch, the ECM disregards\
the kick–down signals and controls
shifting at the normal shift points.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 CHECK HARNESS AND CONNECTOR(KICK DOWN SWITCH – BODY GROUND)
(a) Disconnect the kick–down switch connector.
(b) Measure the voltage according to the value(s) in the table
below.
Standard:
Tester ConnectionSpecified Condition
1 – Body groundBelow 1 Ω
NG REPAIR OR REPLACE HARNESS OR
CONNEC TOR ( SEE PAGE 01–32 )
OK
05L2O–01