2005 TOYOTA AVENSIS fuel pump

A86430
New GasketHollow
Screw
SST
A09663
:Seal Packing
−
ENGINE MECHANICAL CAMSHAFT (1CD−FTV)(From September, 2003)
14 −157
AVENSIS Supplement (RM1045E)
(1) Apply a light coat of soapy water (any fluid to detect
fuel leakage) to the nozzle leakage pipe connec-
tion.
(2) Using SST (a turbocharger pressure gauge), attach SST to the fuel return side of the nozzle leakage
pipe, then maintain 100 kPa (1.0 kgf/cm
2 , 14.5 psi)
of pressure for 60 seconds to check that there are
no bubbles from the pipe connection.
SST 09992 −00242
(3) After checking fuel leaks, wipe off soapy water from the pipe connection.
56. INSTALL CYLINDER HEAD COVER SUB −ASSY
(a) Remove any old packing (FIPG) material.
(b) Apply seal packing to the cylinder head as illustrated. Seal packing: Part No. 08826 −00080 or equivalent
(c) Install the gasket to the cylinder head cover.
(d) Install the cylinder head cover with the 10 bolts. Torque: 13 N
m (135 kgf
cm, 9.7 ft
lbf)
57. INSTALL NOZZLE HOLDER SEAL
(a) Install 4 new nozzle holder seals.
58. INSTALL NOZZLE LEAKAGE PIPE NO.2 (See page 14 −108)
59. INSTALL VACUUM PUMP ASSY (See page 14 −108)
60. INSTALL INJECTION PIPE SUB −ASSY NO.1
NOTICE:
When assembling the pipes, perform the operation with the
engine cold at room temperature.
(a) Install the 2 lower injection pipe clamps to the intake man-
ifold.
(b) Remove the vinyl or plastic bag from the injector and the
vinyl tape from the common rail.
(c) Temporarily install the injection pipe.

A84293
A09660
A85628
(a)
(a)(b)
(b)
A93407SST
A85630
− ENGINE MECHANICALPARTIAL ENGINE ASSY (1CD−FTV)(From September,
2003)14−11 9
AVENSIS Supplement (RM1045E)
95. REMOVE WATER OUTLET SUB−ASSY
(a) Remove the 2 bolts, water outlet and gasket.
96. REMOVE VACUUM PUMP ASSY
(a) Remove the 2 bolts, vacuum pump and 2 O−rings.
97. REMOVE NOZZLE LEAKAGE PIPE NO.2
(a) Disconnect the 2 hoses.
(b) Remove the 2 bolts, nozzle leakage pipe No. 2.
98. REMOVE FUEL INLET PIPE SUB−ASSY
(a) Using SST, remove the fuel inlet pipe from the common
rail side.
SST 09023−12700
(b) Using SST, remove the fuel inlet pipe from the pump side.
SST 09023−12700
99. REMOVE FUEL PIPE NO.3
(a) Remove the fuel pipe insulator.

A84380
A84378
14−122−
ENGINE MECHANICAL PARTIAL ENGINE ASSY (1CD −FTV)(From September,
2003)
AVENSIS Supplement (RM1045E)
116. REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE
(a) Remove the 3 bolts and fuel pipe.
117. REMOVE CRANKSHAFT POSITION SENSOR
(a) Remove the bolt and crankshaft position sensor.
118. REMOVE CAMSHAFT POSITION SENSOR
(a) Remove the bolt and camshaft position sensor. 119. REM O VE ENG I NE CO O L ANT TEM PERAT URESENSOR
120. REPLACE PARTIAL ENGINE ASSY
121. INSTALL ENGINE COOLANT TEMPERATURE SENSOR Torque: 20 N
m (200 kgf
cm, 14 ft
lbf)
122. INSTALL CAMSHAFT POSITION SENSOR Torque: 8.8 N
m (90 kgf
cm, 78 in.
lbf)
123. INSTALL CRANKSHAFT POSITION SENSOR Torque: 8.8 N
m (90 kgf
cm, 78 in.
lbf)
124. INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE
Torque:
8.8 N
m (90 kgf
cm, 78 in.
lbf) for M6
21 N
m (209 kgf
cm, 15 ft
lbf) for M8
125. INSTALL OIL COOLER PIPE
(a) Using a socket wrench for 27 mm, install 2 new gaskets and the oil cooler pipe with the union bolt. Torque: 56 N
m (575 kgf
cm, 42 ft
lbf)
126. INSTALL THERMOSTAT (See Pub. No. RM1018E on page 16 −50)
127. INSTALL WATER INLET (See Pub. No. RM1018E on page 16 −50)
128. INSTALL COMPRESSOR MOUNTING BRACKET NO.1 (W/ AIR CONDITIONING)
Torque: 42 N
m (428 kgf
cm, 31 ft
lbf)
129. INSTALL INJECTION OR SUPPLY PUMP ASSY (See page 11 −58)
130. INSTALL INJECTION PUMP STAY NO.1 (See page 11 −58)
131. INSTALL OIL LEVEL GAGE GUIDE (See page 17 −11 )
132. INSTALL TIMING BELT NO.3 COVER Torque: 7.4 N
m (75 kgf
cm, 65 in.
lbf)

A79196
New O−ring
New O−ring
A79182
Collar
Groove
14−126− ENGINE MECHANICALPARTIAL ENGINE ASSY (1CD−FTV)(From September,
2003)
AVENSIS Supplement (RM1045E)
(c) Using SST, tighten the nut of the fuel inlet pipe on the
pump side.
SST 09023−12700
Torque:
31 N
m (316 kgf
cm, 23 ft
lbf) with SST
34 N
m (347 kgf
cm, 25 ft
lbf) without SST
HINT:
SUse a torque wrench with the fulcrum length of 30 cm
(11.81 in.).
SAfter the inlet pipe is reassembled, check that the used
pipe has no deflection and is installed properly. If it has
deflection or could not be installed properly, replace the
used pipe with a new pipe.
143. INSTALL NOZZLE LEAKAGE PIPE NO.2
Torque: 8.8 N
m (90 kgf
cm, 78 in.
lbf)
144. INSTALL VACUUM PUMP ASSY
(a) Install 2 new O−rings to the vacuum pump.
(b) Align the key of the vacuum pump with the keyway of the
exhaust camshaft, then insert the vacuum pump into
place. Secure the pump with the 2 bolts.
Torque: 21 N
m (214 kgf
cm, 15 ft
lbf)
145. INSTALL WATER OUTLET SUB−ASSY
(a) Install a new gasket and the water outlet with the 2 bolts.
Torque: 21 N
m (209 kgf
cm, 15 ft
lbf)
146. INSTALL EGR VALVE ASSY
(a) Install a new gasket and the EGR valve with the bolt and 2 nuts.
Torque: 18 N
m (184 kgf
cm, 13 ft
lbf)
147. INSTALL INTAKE AIR CONNECTOR
(a) Install a new gasket and the intake air connector together with the diesel throttle body with the 3 bolts.
Torque: 21 N
m (209 kgf
cm, 15 ft
lbf)
148. INSTALL EXHAUST MANIFOLD
(a) Install a new gasket, the exhaust manifold and 8 collars
with new 8 nuts.
Torque: 47 N
m (474 kgf
cm, 34 ft
lbf)
HINT:
When installing the collars, pay attention to the mounting
orientation. The ring groove of the collar should be outward. Re-
fer to the illustration on the left.

141NE−01
A93837
To
Turbocharger
Air Hose No. 2
A93406
SST
14 −90−
ENGINE MECHANICAL VALVE CLEARANCE (1CD−FTV)(From September,
2003)
AVENSIS Supplement (RM1045E)
VALVE CLEARANCE (1CD −FTV)(From September, 2003)
ADJUSTMENT
NOTICE:
S Before removing the injection pipes, clean them up with a soft brush and compressed air.
S After removing the injection pipes, cover the supply pump, common rail and injector mounting
area of the cylinder head cover with vinyl tape to prevent dust from being introduced.
S After removing the cylinder head cover, protect the injector inlet with a vinyl or plastic bag to
prevent foreign objects from being introduced.
HINT:
Inspect and adjust the valve clearance after the engine becomes cold.
1. REMOVE RADIATOR SUPPORT OPENING COVER
2. REMOVE FRONT WHEEL RH
3. REMOVE ENGINE UNDER COVER LH
4. REMOVE ENGINE UNDER COVER SUB −ASSY NO.1
5. REMOVE ENGINE UNDER COVER RH
6. REMOVE ENGINE COVER SUB −ASSY NO.1
(a) Remove the 5 nuts, then remove the engine cover.
7. REMOVE BATTERY
8. REMOVE AIR TUBE NO.1
(a) Disconnect the vacuum hoses and connectors.
(b) Loosen the 2 hose clamps.
(c) Remove the 3 bolts and nut, then detach the air tube No.1.
9. REMOVE TIMING BELT NO.2 COVER (See page 14 −138)
10. REMOVE FUEL PIPE NO.3 (See page 14 −108)
SST 09023 −12700
11. REMOVE INJECTION PIPE SUB −ASSY NO.1
(a) Remove the 2 upper injection pipe clamps from the intake
manifold.
(b) Using SST, remove the injection pipe from the common
rail side.
SST 09023 −12700
(c) Using SST, remove the injection pipe from the injector
side.
SST 09023 −12700
(d) After removing the fuel pipe, in order to prevent dust or foreign objects from being introduced, cover the common
rail with vinyl tape and protect the injector inlet with a vinyl
or plastic bag.

141NB−01
−
ENGINE MECHANICAL CYLINDER HEAD GASKET (2AZ −FSE)
14 −79
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. DISCHARGE FUEL SYSTEM PRESSURE (See page 11 −4)
2. REMOVE FRONT WHEEL RH
3. REMOVE RADIATOR SUPPORT OPENING COVER (See page 14 −23)
4. REMOVE ENGINE ROOM COVER SIDE (See page 14 −23)
5. REMOVE ENGINE UNDER COVER LH (See page 14 −23)
6. REMOVE ENGINE UNDER COVER NO.4 RH (See page 14 −23)
7. REMOVE ENGINE UNDER COVER RH (See page 14 −23)
8. DRAIN COOLANT (See page 16 −7)
9. DRAIN ENGINE OIL (See page 17 −6)
10. REMOVE ENGINE COVER SUB −ASSY NO.1 (See page 14 −45)
11. REMOVE FUEL PRESSURE PULSATION DAMPER ASSY
12. SEPARATE FUEL TUBE SUB −ASSY (See page 11 −4)
13. REMOVE FUEL PIPE SUB −ASSY NO.1 (See page 11 −24)
SST 09023 −12900
14. REMOVE FUEL PUMP ASSY (See page 11 −24)
15. REMOVE FAN AND GENERATOR V BELT (See page 14 −5)
SST 09249 −63010
16. REMOVE GENERATOR ASSY (See page 19 −8)
17. REMOVE EXHAUST PIPE ASSY FRONT (See page 15 −2)
18. SEPARATE VANE PUMP ASSY (See page 14 −45)
19. REMOVE IGNITION COIL ASSY (See page 14 −45)
20. SEPARATE RETURN TUBE SUB −ASSY (See page 14 −45)
21. SEPARATE COOLER REFRIGERANT SUCTION HOSE NO.1 (LHD STEERING POSITION TYPE) (See page 14 −45)
22. REMOVE VANE PUMP OIL RESERVOIR ASSY (See page 14 −45)
23. REMOVE OIL RESERVOIR BRACKET NO.1 (See page 14 −45)
24. SEPARATE ENGINE WIRE (See page 14 −23)
25. REMOVE COOLER BRACKET (LHD STEERING POSITION TYPE) (See page 14 −45)
26. REMOVE ENGINE SERVICE COVER BRACKET RH (RHD STEERING POSITION TYPE)
(See page 14 −45)
27. REMOVE CYLINDER HEAD COVER SUB −ASSY (See page 14 −45)
28. SET NO. 1 CYLINDER TO TDC/COMPRESSION (See page 14 −45)
29. REMOVE ENGINE MOUNTING BRACKET NO.2 RH (See page 14 −45)
30. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR (See page 14 −45)
31. REMOVE CRANKSHAFT PULLEY (See page 14 −45)
SST 09213 −54015 (91651 −60855), 09330 −00021, 09950 −50013 (09951 −05010, 09952 −05010,
09953 −05020, 09954 −05021)
32. REMOVE CHAIN TENSIONER ASSY NO.1 (See page 14 −45)
33. REMOVE CRANKSHAFT POSITION SENSOR (See page 14 −45)
34. REMOVE OIL PAN SUB −ASSY (See page 14 −45)
SST 09032 −00100
35. REMOVE V −RIBBED BELT TENSIONER ASSY (See page 14 −45)
36. REMOVE TIMING CHAIN OR BELT COVER SUB −ASSY (See page 14 −45)
37. REMOVE CRANKSHAFT POSITION SENSOR PLATE NO.1 (See page 14 −45)
38. REMOVE CHAIN TENSIONER SLIPPER (See page 14 −45)
39. REMOVE CHAIN VIBRATION DAMPER NO.1 (See page 14 −45)
40. REMOVE TIMING CHAIN GUIDE (See page 14 −45)
41. REMOVE CHAIN SUB −ASSY (See page 14 −45)

A83481
−
ENGINE MECHANICAL CYLINDER HEAD GASKET (2AZ −FSE)
14 −83
AVENSIS Supplement (RM1045E)
(i) Install the water by −pass pipe with a bolt.
Torque: 9.0 N
m (92 kgf
cm, 80 in.
lbf)
64. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSY
65. INSTALL CAMSHAFT (See page 14 −64)
66. INSTALL NO.2 CAMSHAFT (See page 14 −64)
67. INSTALL EXHAUST MANIFOLD CONVERTER SUB −ASSY (See page 14 −23)
68. INSTALL EXHAUST MANIFOLD HEAT INSULATOR NO.1 (See page 14 −23)
69. INSTALL INTAKE MANIFOLD (See page 11 −13)
70. INSTALL THROTTLE BODY ASSY (See page 10 −8)
71. INSTALL AIR CLEANER ASSEMBLY WITH HOSE (See page 14 −23)
72. INSTALL BATTERY
Torque:
5.0 N
m (51 kgf
cm, 44 in.
lbf) for Bolt
3.5 N
m (36 kgf
cm, 31 in.
lbf) for Nut
73. INSTALL CHAIN VIBRATION DAMPER NO.1 (See page 14 −45)
74. INSTALL CHAIN SUB −ASSY (See page 14 −45)
75. INSTALL TIMING CHAIN GUIDE (See page 14 −45)
76. INSTALL CHAIN TENSIONER SLIPPER (See page 14 −45)
77. INSTALL CRANKSHAFT POSITION SENSOR PLATE NO.1 (See page 14 −45)
78. INSTALL TIMING CHAIN OR BELT COVER SUB −ASSY (See page 14 −45)
79. INSTALL V −RIBBED BELT TENSIONER ASSY (See page 14 −45)
80. INSTALL OIL PAN SUB −ASSY (See page 14 −45)
81. INSTALL CRANKSHAFT POSITION SENSOR (See page 14 −45)
82. INSTALL CRANKSHAFT PULLEY (See page 14 −45)
SST 09213 −54015 (91651 −60855), 09330 −00021
83. INSTALL CHAIN TENSIONER ASSY NO.1 (See page 14 −45)
84. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR
Torque: 52 N
m (530 kgf
cm, 38 ft
lbf)
85. INSTALL ENGINE MOUNTING BRACKET NO.2 RH (See page 14 −45)
86. INSTALL CYLINDER HEAD COVER SUB −ASSY (See page 14 −45)
87. INSTALL COOLER BRACKET (LHD STEERING POSITION TYPE)
Torque: 9.0 N
m (92 kgf
cm, 80 in.
lbf)
88. INSTALL ENGINE SERVICE COVER BRACKET RH (RHD STEERING POSITION TYPE) Torque: 9.0 N
m (92 kgf
cm, 80 in.
lbf)
89. INSTALL OIL RESERVOIR BRACKET NO.1 Torque: 8.0 N
m (82 kgf
cm, 71 in.
lbf)
90. INSTALL COOLER REFRIGERANT SUCTION HOSE NO.1 (LHD STEERING POSITION TYPE)
91. INSTALL RETURN TUBE SUB −ASSY
Torque: 8.0 N
m (82 kgf
cm, 71 in.
lbf)
92. INSTALL IGNITION COIL ASSY
Torque: 9.0 N
m (92 kgf
cm, 80 in.
lbf)
93. INSTALL FUEL PUMP ASSY (See page 11 −24)

14−84
−
ENGINE MECHANICAL CYLINDER HEAD GASKET (2AZ −FSE)
AVENSIS Supplement (RM1045E)
94. INSTALL FUEL PIPE SUB −ASSY NO.1 (See page 11 −24)
SST 09023 −12900
95. INSTALL FUEL TUBE SUB −ASSY (See page 11 −24)
96. INSTALL FUEL PRESSURE PULSATION DAMPER ASSY (See page 11 −24)
97. INSTALL ENGINE COVER SUB −ASSY NO.1
Torque: 7.0 N
m (71 kgf
cm, 62 in.
lbf)
98. INSTALL VANE PUMP ASSY Torque: 37 N
m (377 kgf
cm, 27 ft
lbf)
99. INSTALL EXHAUST PIPE ASSY FRONT (See page 15 −2)
100. INSTALL GENERATOR ASSY (See page 19 −8)
101. INSTALL FAN AND GENERATOR V BELT (See page 14 −5)
SST 09249 −63010
102. ADD COOLANT (See page 16 −7)
103. ADD ENGINE OIL (See page 17 −6)
104. CHECK FOR ENGINE COOLANT LEAKS (See page 16 −1)
105. CHECK FOR ENGINE OIL LEAKS
106. CHECK FOR FUEL LEAKS (See page 11 −4)
107. INSTALL FRONT WHEEL RH Torque: 103 N
m (1,050 kgf
cm, 76 ft
lbf)
108. ADD POWER STEERING FLUID (See Pub. No. RM1018E on page 51 −4)
109. BLEED POWER STEERING FLUID (See Pub. No. RM1018E on page 51 −4)
110. CHECK POWER STEERING FULUID LEVEL IN RESERVOIR
(See Pub. No. RM1018E on page 51 −4)
111. CHECK FUNCTION OF THROTTLE BODY