A66053
Engine Room R/B No.4EFI Relay
A79066
Engine Room R/B No.4EFI No.1 Fuse
1
2
A54396Mass Air Flow Meter Connector
Wire Harness Side
+B
A6
A18294
EVG
ECM Connector E12
05±28
±
DIAGNOSTICS SFI SYSTEM(1ZZ±FE/3ZZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)
5CHECK HARNESS AND CONNECTOR(EFI RELAY ± MASS AIR FLOW METER)
(a)Remove the EFI relay from the engine room R/B No.4.
(b)Remove the EFI No.1 fuse from the engine room R/B No.4.
(c)Disconnect the mass air flow meter connector.
(d)Check for continuity between the wire harness side con- nectors.
Standard (Check for open):
Symbols (Terminal No.)Specified condition
EFI relay (3) ± EFI No.1 fuse (1)ContinuityEFI No.1 fuse (2) ± +B (A6±1)Continuity
Standard (Check for short):
Symbols (Terminal No.)Specified condition
EFI relay (3) or EFI No.1 fuse (1) ± Body groundNocontinuityEFI No.1 fuse (2) or +B (A6±1) ± Body groundNo continuity
NOTICE:
Do not insert the tester leads hard in the procedure (c), the
holder may be damaged.
NGREPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK ECM POWER SOURCE CIRCUIT (See page 05±124)
6INSPECT ECM
(a)Check for continuity between the terminal of the E12 ECM connector and the body ground.
Standard:
Symbols (Terminal No.)Specified condition
EVG (E12±32) ± Body groundContinuity
NGCHECK AND REPLACE ECM (See page 01±32)
OK
0505L±04
05±22
±
DIAGNOSTICS SFI SYSTEM(1ZZ±FE/3ZZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)
PROBLEM SYMPTOMS TABLE
When the malfunction code is not confirmed in the diagnostic trouble code check and the problem still can\
not be confirmed in the basic inspection, proceed to this problem symptoms \
tables and troubleshoot accord-
ing to the numbered order given below.
SymptomSuspect AreaSee page
Engine does not crank (Does not start)1. Starter and starter relay
2. Neutral start switch circuit*19±1
No initial combustion (Does not start)
1. ECM power source circuit
2. Ignition coil (w/ Igniter) circuit
3. Fuel pump control circuit
4. Fuel system05±124
05±103
05±131
11±1
No complete combustion (Does not start)
1. Fuel pump control circuit
2. Ignition coil (w/ Igniter) circuit
3. Fuel system05±131
05±103
11±1
Engine cranks normally (Difficult to start)
1. Starter signal circuit
2. ISC valve circuit
3. Fuel pump control circuit
4. Ignition coil (w/ Igniter)
5. Spark plug
6. Compression
7. Fuel system05±135
05±100
05±131
05±10318±3
14±111±1
Cold engine (Difficult to start)
1. Starter signal circuit
2. ISC valve circuit
3. Fuel pump control circuit
4. Fuel system
5. Ignition coil (w/ Igniter)
6. Spark plug05±135
05±100
05±131 11±1
05±103 18±3
Hot engine (Difficult to start)
1. Starter signal circuit
2. ISC valve circuit
3. Fuel pump control circuit
4. Fuel system
5. Ignition coil (w/ Igniter)
6. Spark plug05±135
05±100
05±131 11±1
05±103 18±3
Incorrect first idle (Poor idling)1. ISC valve circuit05±100
High engine idle speed (Poor idling)
1. ISC valve circuit
2. ECM power source circuit
3. Neutral start switch circuit*05±100
05±124
Low engine idle speed (Poor idling)
1. ISC valve circuit
2. Neutral start switch circuit*
3. Fuel pump control circuit
4. Fuel system05±100
05±131 11±1
Rough idling (Poor idling)
1. ISC valve circuit
2. ECM power source circuit
3. Fuel pump control circuit05±100
05±124
05±131
Hunting (Poor idling)
1. ISC valve circuit
2. ECM power source circuit
3. Fuel pump control circuit05±100
05±124
05±131
Hesitation/Poor acceleration (Poor drivability)
1. Fuel system
2. Fuel pump control circuit
3. Ignition coil (w/ Igniter) circuit11±1
05±131
05±103
Muffler explosion, after fire (Poor drivability)
1. Ignition coil (w/ Igniter) circuit
2. Spark plug
3. Fuel system05±103 18±3
11±1
Surging (Poor drivability)
1. Fuel pump control circuit
2. Spark plug
3. Fuel system05±131 18±3
11±1
±
DIAGNOSTICS SFI SYSTEM (1ZZ±FE/3ZZ±FE)
05±23
AVENSIS REPAIR MANUAL (RM1018E)
Engine stall (Soon after starting)
1. Fuel pump control circuit
2. ISC valve circuit05±131
05±100
Engine stall (After accelerator pedal released)
1. Injector circuit
2. ISC valve circuit
3. ECM11±8
05±100
05±20
Engine stall (When shifting from N to D)1. Neutral start switch circuit
2. ISC valve circuit
05±100
*: A/T only.
05B3M±03
A79104
Fuel Pump
Circuit Opening Relay
ECM
DLC3
Camshaft Position
Sensor
Engine Coolant
Temperature Sensor
Camshaft Timig OIL
Control Valve Assy
Crankshaft
Position Sensor
Knock Sensor
Mass Air Flow Meter Assy
Heated Oxygen Sensor
(Bank 1 Sensor 1)
Engine Room R/B No.1
Heated Oxygen Sensor
(Bank 1 Sensor 2)
Engine Room R/B No.4
Ignition Coil and Igniter
Injector
Power Steering Oil
Pressure Switch
Idle Speed Control
Valve Assy
Throttle Position Sensor
Vacuum Switching Valve
(for ISC)
VSV for EVAP
± DIAGNOSTICSSFI SYSTEM (1ZZ±FE/3ZZ±FE)
05±19
AVENSIS REPAIR MANUAL (RM1018E)
LOCATION
0505J±04
05±16
±
DIAGNOSTICS SFI SYSTEM (1ZZ±FE/3ZZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to \
the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in the check mode, check the circuit f\
or the codes
listed in the table below. For details of each code, refer to the ''See page '' under the respective ''DTC No.''
in the DTC chart.
DTC No.
(See page)Detection ItemTrouble Area*1
CHK ENGMemory
P0100
(05±24)Mass Air Flow Circuit Malfunc-
tion Open or short in mass air flow meter circuit
Mass air flow meter
ECM
P0110
(05±30)Intake Air Temperature Circuit
Malfunction Open or short in intake air temp. sensor circuit
Intake air temp. sensor (built into mass air flow meter)
ECM
P0115
(05±34)Engine Coolant Temperature Cir-
cuit Malfunction Open or short in engine coolant temperature sensor circuit
Engine coolant temperature sensor
ECM
P0116
(05±38)Engine Coolant Temperature Cir-
cuit Range/Performance Prob-
lem Engine coolant temperature sensor
Thermostat
P0120
(05±39)Throttle Pedal Position Sensor/
Switch ºAº Circuit Malfunction Open or short in throttle position sensor circuit
Throttle position sensor
ECM
P0121
(05±44)Throttle Pedal Position Sensor/
Switch ºAº Circuit Range/Perfor-
mance Problem
Throttle position sensor
P0125
(05±45)Insufficient Coolant Temp. for
Closed Loop Fuel Control
Open or short in heated oxygen sensor circuit
Heated oxygen sensor
Air induction system
Fuel pressure
Injector
Gas leakage on exhaust system
ECM
P0130*3
(05±54)
Oxygen Sensor Circuit Malfunc-
tion (Bank 1 Sensor 1)
Open or short in heated oxygen sensor circuit
Heated oxygen sensor
Air induction system
Fuel pressure
Injector
P0133*3
(05±60)
Oxygen Sensor Circuit Slow Re-
sponse (Bank 1 Sensor 1)
Open or short in heated oxygen sensor circuit
Heated oxygen sensor
Air induction system
Fuel pressure
Injector
ECM
P0135
(05±65)Oxygen Sensor Heater Circuit
Malfunction (Bank 1 Sensor 1) Open or short in heater circuit of heated oxygen sensor
Heated oxygen sensor heater
ECM
P0136
(05±54)Oxygen Sensor Circuit Malfunc-
tion (Bank 1 Sensor 2) Open or short in heated oxygen sensor circuit
Heated oxygen sensor
P0141
(05±65)Oxygen Sensor Heater Circuit
Malfunction (Bank 1 Sensor 2) Open or short in heater circuit of heated oxygen sensor
Heated oxygen sensor heater
ECM
±
DIAGNOSTICS SFI SYSTEM (1ZZ±FE/3ZZ±FE)
05±17
AVENSIS REPAIR MANUAL (RM1018E)P0171*
3
(05±67)
System too Lean (Fuel Trim)
(Bank1)
Air induction system
Injector blockage
PCV hose
Mass air flow meter
Engine coolant temperature sensor
Fuel pressure
Open or short in heated oxygen sensor circuit
Heated oxygen sensor
ECM
P0172*3
(05±67)
System too Rich (Fuel Trim)
(Bank1)
Injector leak, blockage
Mass air flow meter
Engine coolant temperature sensor
Ignition system
Fuel pressure
Open or short in heated oxygen sensor circuit
Gas leakage in exhaust system
Heated oxygen sensor
ECM
P0300*3
(05±73)
Random/Multiple Cylinder Misfire
DetectedOpen or short in engine wire
Connector connection
Vac m hose connectionP0301*3
(05±73)Cylinder 1 Misfire Detected
Vacuum hose connection
PCV hose
Ignition system
P0302*3
(05±73)Cylinder 2 Misfire Detected
Injector
Fuel pressure
Mass air flow meter
P0303*3
(05±73)Cylinder 3 Misfire Detected
Mass air flow meter
Engine coolant temperature sensor
Compression pressure
Valve clearance
P0304*3
(05±73)Cylinder 4 Misfire Detected
Valve clearance
Valve timing
ECM
P0325
(05±81)Knock Sensor 1 Circuit Malfunc-
tion (Bank 1) Open or short in knock sensor circuit
Knock sensor (under±torqued or loose)
ECM
P0335
(05±84)Crankshaft Position Sensor ºAº
Circuit Malfunction
Open or short in crankshaft position sensor circuit
Crankshaft position sensor
Crank angle sensor plate
ECM
P0340
(05±88)Camshaft Position Sensor Circuit
Malfunction
Open or short in camshaft position sensor circuit
Camshaft position sensor
Intake camshaft
Timing chain has jumped a tooth
ECM
P0420*3
(05±91)
Catalyst System Efficiency Be-
low Threshold (Bank 1)
Gas leakage in exhaust system
Heated oxygen sensor
Three±way catalytic converter
ECM
P0443
(05±94)Evaporative Emission Control
System Purge Control Vent Cir-
cuit Malfunction Open or short in VSV for EVAP circuit
VSV for EVAP
ECM
P0500
(05±98)Vehicle Speed Sensor Malfunc-
tion
Open or short in speed sensor circuit
Speed sensor
Combination meter
ECM
Skid control ECU
05±18
±
DIAGNOSTICS SFI SYSTEM (1ZZ±FE/3ZZ±FE)
AVENSIS REPAIR MANUAL (RM1018E) P0505*
3
(05±100)Idle Control System Malfunction
Open or short in ISC valve circuit
ISC valve is stuck or closed
PCV hose
A/C switch circuit
Air induction system
ECM
P1300
(05±103)Igniter Circuit Malfunction (No. 1)
Ignition system
Open or short in IGF or IGT1 circuit from No. 1 ignition coil
with igniter to ECM
No. 1 ignition coil with igniter
ECM
P1305
(05±103)Igniter Circuit Malfunction (No. 2)
Ignition system
Open or short in IGF or IGT2 circuit from No. 2 ignition coil
with igniter to ECM
No. 2 ignition coil with igniter
ECM
P1310
(05±103)Igniter Circuit Malfunction (No. 3)
Ignition system
Open or short in IGF or IGT3 circuit from No. 3 ignition coil
with igniter to ECM
No. 3 ignition coil with igniter
ECM
P1315
(05±103)Igniter Circuit Malfunction (No. 4)
Ignition system
Open or short in IGF or IGT4 circuit from No. 4 ignition coil
with igniter to ECM
No. 4 ignition coil with igniter
ECM
P1335
(05±84)Crankshaft Position Sensor Cir-
cuit Malfunction (During engine
running) Open or short in crankshaft position sensor circuit
Crankshaft position sensor
Crank angle sensor plate
ECM
P1346
(05±111)VVT Sensor/Camshaft Position
Sensor Circuit Range/Perfor-
mance Problem (Bank 1) Mechanical system (Timing chain has janped a tooth, chain
stretched)
ECM
P1349
(05±112)VVT System Malfunction (Bank
1)
Valve timing
OCV
VVT controller assembly
ECM
P1520*2
(05±115)
Stop Light Switch Circuit Mal-
functionOpen or short in stop light switch signal circuit
Stop light switch
ECM
P1600
(05±119)ECM BATT Malfunction Open in back up power source circuit
ECM
P1656
(05±122)OCV Circuit Malfunction (Bank
1) Open or short in OCV circuit
OCV
ECM
*1: ... CHK ENG is illuminated. ... CHK ENG is not illuminated.
*
2: Only for A/T models.
*
3: For European spec. only
05±2
±
DIAGNOSTICS SFI SYSTEM(1ZZ±FE/3ZZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)
9SYMPTOM SIMULATION
10DTC CHECK (See page 05±5)
AMalfunction code
BNo code
B GO TO STEP 12
A
11DTC CHART (See page 05±16)
GO TO STEP 14
12BASIC INSPECTION (See page 05±5)
AWrong parts not confirmed
BWrong parts confirmed
B GO TO STEP 17
A
13PROBLEM SYMPTOMS TABLE (See page 05±22)
AWrong circuit confirmed
BWrong parts confirmed
B GO TO STEP 17
A
14CHECK ECM POWER SOURCE CIRCUIT (See page 05±124)
15 CIRCUIT INSPECTION
AMalfunction not confirmed
BMalfunction confirmed
B GO TO STEP 18
A