2005 NISSAN X-TRAIL Install head

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-107
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003C1
PARKING AND TAIL LAMPS
Refer to LT- 3 7 , "Bulb Replacement of Headlamp and Clearance lamp" in “HEADLAMP -CONVENTIONAL
TYPE-” or LT- 2 0 , "
Bulb Replacement of Headlamp and Clearance Lamp" in “HEADLAMP -XENON TYPE-”.
TAIL LAMP
Refer to LT- 11 9 , "Bulb Replacement" in “REAR COMBINATION LAMP”.
LICENSE PLATE LAMP
1. Remove license plate lamp mounting screws.
2. Remove lens of license plate lamp.
3. Remove bulb from its socket.
4. Installation is the reverse order of removal.
Removal and Installation EKS003C2
PARKING LAMP
Refer to LT- 3 8 , "Removal and Installation of Headlamp" in “HEADLAMP -CONVENTIONAL TYPE-” or LT- 2 1 ,
"Removal and Installation of Headlamp" in “HEADLAMP -XENON TYPE-”.
TAIL LAMP
Refer to LT- 11 9 , "Removal and Installation" in “REAR COMBINATION LAMP”.
LICENSE PLATE LAMP
Removal
1. Remove the license lamp finisher. Refer to EI-31, "LICENSE
LAMP FINISHER" in “EXTERIOR & INTERIOR (EI)” section.
2. Remove the harness from installation pawl for harness.
3. Remove license plate lamp mounting screws (2 each, RH and
LH).
4. Pull out license plate lamp from license lamp finisher.
Installation
Installation is the reverse order of removal.License plate lamp : 12V - 5W
PKIA8753E
PKIA5760E
License plate lamp mounting screws
: 1.4 N·m (0.15 kg-m, 13 in-lb)

LT-116
CLEARANCE LAMP/TAIL LAMP

CLEARANCE LAMP/TAIL LAMPPFP:26010
Bulb Replacement (Clearance Lamp)EKS001UR
Refer to LT- 2 0 , "Bulb Replacement of Headlamp and Clearance Lamp" in “HEADLAMP-XENON TYPE-” or
LT- 3 7 , "
Bulb Replacement of Headlamp and Clearance lamp" in “HEADLAMP-CONVENTIONAL TYPE-”.
Bulb Replacement (Tail lamp)EKS001US
Refer to LT- 11 9 , "Bulb Replacement" in “REAR COMBINATION LAMP”.
Removal and Installation of Clearance LampEKS001UT
Refer to LT- 2 1 , "Removal and Installation of Headlamp" in “HEADLAMP-XENON TYPE-” or LT- 3 8 , "Removal
and Installation of Headlamp" in “HEADLAMP-CONVENTIONAL TYPE-”.
Removal and Installation of Tail lampEKS001UU
Refer to LT- 11 9 , "Removal and Installation" in “REAR COMBINATION LAMP”.

WW-1
WIPER, WASHER & HORN
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION WW
A
B
WW

WIPER, WASHER & HORN
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Wiring Diagrams and Trouble Diagnosis .................. 3
FRONT WIPER AND WASHER SYSTEM .................. 4
System Description .................................................. 4
WIPER OPERATION ............................................ 4
WASHER OPERATION ......................................... 5
Wiring Diagram — WIPER — .................................. 6
Wiring Diagram — WIPER —/LHD models .............. 7
Terminal and Reference Values for Combination
Switch ....................................................................... 8
Removal and Installation of Front Wiper Arms,
Adjustment for Wiper Arms Stop Location ............... 8
Removal and Installation of Front Wiper Drive
Assembly .................................................................. 9
REMOVAL ............................................................. 9
INSTALLATION ................................................... 10
Front Washer Nozzle Adjustment ............................ 11
Washer Tube Layout ............................................... 11
Removal and Installation of Front Washer Nozzle ... 12
REMOVAL ........................................................... 12
INSTALLATION ................................................... 12
Inspection for Front Washer Nozzle ....................... 12
CHECK VALVE ................................................... 12
Removal and Installation of Wiper and Washer
Switch ..................................................................... 12
REMOVAL ........................................................... 12
INSTALLATION ................................................... 12
Removal and Installation of Washer Tank .............. 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 13
Removal and Installation of Washer Motor ............ 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 13
REAR WIPER AND WASHER SYSTEM .................. 14
Wiring Diagram — WIP/R — .................................. 14
Terminal and Reference Values for Combination
Switch ..................................................................... 16Removal and Installation of Rear Wiper Arms ........ 16
WIPER ARMS ..................................................... 16
Removal and Installation of Rear Wiper Motor ....... 17
REMOVAL ........................................................... 17
INSTALLATION ................................................... 17
Rear Washer Nozzle Adjustment ........................... 18
Removal and Installation of Rear Washer Nozzle ... 18
REMOVAL ........................................................... 18
INSTALLATION ................................................... 18
Inspection for Rear Washer Nozzle ........................ 18
CHECK VALVE .................................................... 18
Removal and Installation of Wiper and Washer
Switch ..................................................................... 19
Removal and Installation of Washer Tank .............. 19
Removal and Installation of Washer Motor ............. 19
Washer Tube Layout .............................................. 19
HEADLAMP WASHER ............................................. 20
System Description ................................................. 20
Wiring Diagram —HLC— ....................................... 21
Wiring Diagram —HLC—/RHD models .................. 23
Removal and Installation of Headlamp Washer Noz-
zle ........................................................................... 25
REMOVAL ........................................................... 25
INSTALLATION ................................................... 25
Inspection for Headlamp Washer Nozzle ............... 25
CHECK VALVE .................................................... 25
Removal and Installation of Washer Tank .............. 25
Removal and Installation of Washer Motor ............. 25
Washer Tube Layout .............................................. 26
HORN ........................................................................ 27
Wiring Diagram — HORN — .................................. 27
Removal and Installation ........................................ 28
REMOVAL ........................................................... 28
INSTALLATION ................................................... 28
CIGARETTE LIGHTER ............................................. 29
Wiring Diagram — CIGAR — ................................. 29
Removal and Installation ........................................ 30
REMOVAL ........................................................... 30
INSTALLATION ................................................... 30
POWER SOCKET ..................................................... 31

HEADLAMP WASHER
WW-25
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation of Headlamp Washer NozzleEKS0036J
REMOVAL
1. Remove front bumper. Refer to EI-14, "FRONT BUMPER"
2. Remove hose clip and metal clip.
3. Remove headlamp washer nozzle from front bumper.
INSTALLATION
Installation is in the reverse order of removal.
Inspection for Headlamp Washer NozzleEKS0036K
CHECK VALVE
Blow air in the injection direction, and check that air flows only one
way. Make sure that the reverse direction is not possible.
Removal and Installation of Washer TankEKS0036L
Refer to WW-13, "Removal and Installation of Washer Tank" .
Removal and Installation of Washer MotorEKS0036M
1. Remove front bumper. Refer to EI-14, "FRONT BUMPER"
2. Remove washer motor connector and hose.
3. Pull out washer motor in the direction of the arrow in the figure,
and remove the washer motor from the washer tank.
CAUTION:
When installing washer motor, there should be no packing
twist, etc.
PKIA0490E
PKIA0491E
PKIC0596E

MA-6
GENERAL MAINTENANCE

GENERAL MAINTENANCEPFP:00000
General MaintenanceELS000AL
General maintenance includes those items which should be checked during the normal day-to-day operation
of the vehicle. They are essential if the vehicle is to continue operating properly. The owners can perform the
checks and inspections themselves or they can have their NISSAN dealers do them for a nominal charge.
OUTSIDE THE VEHICLE
The maintenance items listed here should be performed from time to time, unless otherwise specified.
INSIDE THE VEHICLE
The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the
vehicle, etc.
UNDER THE HOOD AND VEHICLE
The maintenance items listed here should be checked periodically e.g. each time you check the engine oil or refuel.Item Reference page
TiresCheck the pressure with a gauge periodically when at a service station, includ-
ing the spare, and adjust to the specified pressure if necessary. Check carefully
for damage, cuts or excessive wear.—
Windshield wiper
bladesCheck for cracks or wear if not functioning correctly. —
Doors and engine
hoodCheck that all doors, the engine hood, the trunk lid and back door operate prop-
erly. Also ensure that all latches lock securely. Lubricate if necessary. Make sure
that the secondary latch keeps the hood from opening when the primary latch is
released.
When driving in areas using road salt or other corrosive materials, check for
lubrication frequently.BL-12
, BL-18
Tire rotationTires should be rotated every 10,000 km (6,000 miles) for 2WD models and
every 5,000 km (3,000 miles) for 4WD models.MA-43
Item Reference page
LampsMake sure that the headlamps, stop lamps, tail lamps, turn signal lamps, and
other lamps are all operating properly and installed securely. Also check head-
lamp aim.—
Warning lamps and
chimesMake sure that all warning lamps and buzzers/chimes are operating properly. —
Steering wheelCheck that it has the specified play.
Check for changes in the steering conditions, such as excessive free play, hard
steering or strange noises.
Free play: Less than 35 mm (1.38 in)—
Seat beltsCheck that all parts of the seat belt system (e.g. buckles, anchors, adjusters and
retractors) operate properly and smoothly, and are installed securely. Check the
belt webbing for cuts, fraying, wear or damage.MA-47
Item Reference page
Windshield washer
fluidCheck that there is adequate fluid in the tank. —
Engine coolant levelCheck the coolant level when the engine is cold.MA-20
(QR20DE,
QR25DE)
MA-30
(YD22DDTi)
Engine oil levelCheck the level after parking the vehicle on a level spot and turning off the
engine.MA-24
(QR20DE,
QR25DE)
MA-35
(YD22DDTi)
Brake and clutch fluid
levelsMake sure that the brake and clutch fluid levels are between the “MAX” and
“MIN” lines on the reservoir.MA-39
, MA-44
BatteryCheck the fluid level in each cell. It should be between the “MAX” and “MIN”
lines.—

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
EC-1641
Basic inspection .. EC-79, EC-578, EC-1012, EC-1382
Battery ................................................................. SC-4
Baulk ring (M/T) .................................... MT-23, MT-41
Blower motor .... ATC-82, ATC-87, ATC-127, MTC-15,
MTC-18
, MTC-24
Blower resistor ................................................ MTC-25
Blower unit ....................... ATC-125, MTC-22, MTC-24
BOOST - Wiring diagram ............... EC-1153, EC-1508
Boring/horning cylinder block(QR20DE-QR25DE) .......
EM-111
Brake booster .................................................... BR-23
Brake fluid change ............................................... BR-8
Brake fluid level ................................................. MA-44
Brake fluid level and line check ........................... BR-8
Brake hydraulic line ........................................... BR-10
Brake inspection ................................................ MA-44
Brake lines and cables inspection ..................... MA-44
Brake master cylinder ........................................ BR-14
Brake pedal ......................................................... BR-6
Brake switch ..... EC-405, EC-809, EC-1313, EC-1664
BRK/SW - Wiring diagram EC-406, EC-811, EC-1314,
EC-1665
Bulb specifications ............................................ LT-152
Bumper, front ....................................................... EI-14
Bumper, rear ........................................................ EI-17
C
Camshaft inspection(QR20DE-QR25DE) .......... EM-58
Camshaft inspection(YD22DDTi) .................... EM-181
Camshaft position sensor (CMPS) EC-1169, EC-1175,
EC-1525
, EC-1531
Camshaft position sensor (PHASE) .. EC-257, EC-701
Camshaft(QR20DE-QR25DE) ........................... EM-56
Camshaft(YD22DDTi) ...................................... EM-180
CAN - Wiring diagram ....... EC-134, EC-634, EC-1057,
EC-1426
, LAN-12, LAN-28, LAN-44, LAN-69, LAN-87,
LAN-105
, LAN-131, LAN-144, LAN-157
CAN (Controller Area Network) ........ LAN-11, LAN-27,
LAN-43
, LAN-68, LAN-86, LAN-104, LAN-130,
LAN-143
, LAN-156
CAN communication EC-39, EC-133, EC-552, EC-633,
EC-989
, EC-1056, EC-1365, EC-1425, AT-32, AT-97,
AT-329
, TF-45, LAN-11, LAN-27, LAN-43, LAN-68,
LAN-86
, LAN-104, LAN-130, LAN-143, LAN-156
Canister-See EVAP canister ............. EC-525, EC-965
CHARGE - Wiring diagram .................... SC-14, SC-15
Charging system ................................................ SC-13
Chassis and body maintenance ........................ MA-39
CHIME - Wiring diagram ................ DI-54, DI-57, DI-58
CIGAR - Wiring diagram .................................. WW-29
Cigarette lighter ............................................... WW-29
Circuit breaker ................................................... PG-12
CKPS - Wiring diagram EC-1059, EC-1158, EC-1164,
EC-1428
, EC-1513, EC-1520
Clearance lamp ................................................ LT-116
Clock ................................................................... DI-63
CLOCK - Wiring diagram .................................... DI-63
Closed loop control .............................. EC-36, EC-549
Clutch cover ....................................................... CL-16
Clutch disc ......................................................... CL-16
Clutch master cylinder ......................................... CL-9
Clutch operating cylinder ................................... CL-12
Clutch pedal ......................................................... CL-5
Clutch release bearing ....................................... CL-14
Clutch release mechanism ................................ CL-14
Clutch withdrawal lever ...................................... CL-14
CMPS - Wiring diagram EC-1059, EC-1170, EC-1176,
EC-1428
, EC-1526, EC-1532
Coil spring (rear) ............................................... RSU-8
Collision diagnosis .......................................... SRS-48
Combination meter ............................................... DI-4
Combination switch ............................................. LT-96
Component Location (auto A/C) ......... ATC-35, MTC-4
Compression pressure(QR20DE-QR25DE) ..... EM-70
Compression pressure(YD22DDTi) ................ EM-209
Compressor clutch removal and installation .. ATC-146
Compressor special service tool ...................... ATC-14
Condenser ..................................................... ATC-155
Connecting rod bearing clearance(QR20DE-QR25DE)
EM-109
Connecting rod bearing clearance(YD22DDTi) EM-252
Connecting rod bushing clearance(YD22DDTi) EM-246
Connecting rod(QR20DE-QR25DE) ............... EM-109
Connecting rod(YD22DDTi) .............. EM-242, EM-248
CONSULT for engine ......................... EC-103, EC-604
CONSULT-II for engine ................. EC-1034, EC-1405
Control lever (M/T) ............................................. MT-16
Control unit ..................................... ATC-120, MTC-21
Control units (terminal arrangement) ................. PG-76
Controller Area Network (CAN) ........ LAN-11, LAN-27,
LAN-43
, LAN-68, LAN-86, LAN-104, LAN-130,
LAN-143
, LAN-156
Converter housing installation ......................... AT-523
COOL/F - Wiring diagram EC-356, EC-759, EC-1127,
EC-1483
Coolant replacement(QR20DE-QR25DE) ........ MA-20
Coolant replacement(YD22DDTi) ..................... MA-30
Cooling circuit (engine)(QR20DE-QR25DE) ....... CO-7
Cooling circuit (engine)(YD22DDTi) ................. CO-30
Cooling fan ............................................ CO-19, CO-37
Cooling fan relay EC-367, EC-770, EC-1137, EC-1492
Coupling sleeve (M/T) ........................... MT-23, MT-41
Cowl top .............................................................. EI-20
Cowl top cover .................................................... EI-20
Crankcase ventilation system .......... EC-989, EC-1365
Crankcase ventilation system - See Positive crankcase
ventilation ........................................... EC-527
, EC-967
Crankshaft position sensor (POS) ..... EC-250, EC-693
Crankshaft position sensor (TDC) EC-1157, EC-1163,
EC-1512
, EC-1518
Crankshaft(QR20DE-QR25DE) ........................ EM-90
Cylinder block boring(QR20DE-QR25DE) ...... EM-112
Cylinder block boring(YD22DDTi) ................... EM-250
Cylinder block(QR20DE-QR25DE) ................... EM-89
Cylinder block(YD22DDTi) .............................. EM-230
Cylinder head bolt tightening(QR20DE-QR25DE) ........