2005 MITSUBISHI LANCER EVOLUTION IX exhaust

194G6 – ROCKER ARM / CAMSHAFT
Installation Service Point
Installation of OCV filter
Note :
Before fitting the filter, check that it is clean and is not damaged
or deformed in any way.
Installation of eye bolt
Note :
The oil pump may be damaged if the oil pipe joint turns with the
eye bolt when it is fitted.
Hold the oil pipe joint in place with a spanner, etc., and then tighten
the eye bolt to the specified torque 42 ±2 N-m.
Installation of cam position sensor
support
1. Wipe away all traces of the old liquid gasket left on the cam
position sensor support and the cylinder head.
2. Apply a 3 mm-thick coat of the liquid gasket to the parts of the
cam position sensor support indicated on the diagram.
Liquid Gasket
Product name : MZ100191 or equivalent
Installation of cam position sensing
cylinder
1. Set the camshaft to the top dead centre for No.1.
2. Install the various vanes of the cam position sensing cylinder at
the positions indicated on the diagram.
Installation of cover / gasket
1. Before installing the cover and gasket, put the camshaft to the
No.1 top dead centre position, and check that the vanes of the
respective sensing cylinders are located in the positions shown in
the diagram.
Eye bolt
Hold with
spanner, etc.
Oil pipe joint
Exhaust sideIntake side
Exhaust side
Exhaust sideIntake side
Intake sideVane
Vane
Vane
Vane VaneVane
Vane Vane
Vane
(large) Vane
(large) Vane
(small)
Vane
(small)
A
*
B

*
C


*
D


*
E


*

204G6 – ROCKER ARM / CAMSHAFT
2. Ensure that the cutaways in the intake side cover and the tabs on the
gasket are aligned with the positions shown in the diagram, and
tighten at the specified torque of 14 ±1 N-m. The exhaust side cover
and gasket do not have a specified installation direction.
Comment :
The cover and gasket do not have distinct front and rear sides.
No cutawayNo installation direction Exhaust side
Intake side
Ta b Ta b
Cutaway
Cutaway

*

*


A


*


*


*


*


*


*



*

*

LAYOUT DIAGRAMS - ENGINE / TRANSMISSION1-8
B-106 (2-grey) Knock sensor
B-108 (2-black) Coolant temperature sensor
B-109 (34-black) ABS-ECU
B-114 (1-black) Water temperature gauge unit
B-115 (3-black) Exhaust cam position sensorB-119 (3-grey) Ignition coil 2
B-122 (3-black) Crank angle sensor
B-123 (3-grey) Ignition coil 1
B-124 (2-black) Fuel pressure solenoid valve
Engine / Transmission (continued)
Connector Symbol
Control harness
Battery harness

INDIVIDUAL PART INSTALLATION POSITIONS - ECU2-4
O
2sensor
connector
Ext. air temp. sensor
Coolant
temperature sensor
Intake cam
position sensor
Exhaust cam
position sensor
(Vehicle not fitted with front passenger airbag)
O2 sensor
Front impact sensor
Steer sensor
Sunlight sensor
Heater water temperature sensor
Air thermo
sensor
Blower
ASSY
Cabin
temperature sensor

PART INSTALLATION POSITIONS - EARTHS2-16
Engine ECU
Exhaust cam
position sensorSunroof motor
ASSY

CIRCUIT DIAGRAMS - ENGINE CONTROL SYSTEM3-30
Engine control system (continued)
Engine control relay
Air flow
sensor
Engine
ECU
•ACD (vehicle
w/out AYC)
•ACD, AYC Air pressure
sensor Intake temp.
sensor J/C (6)
(Engine control relay)
Exhaust cam
position
sensorIntake cam
position
sensor
Throttle position
sensorCoolant temperature
sensor Air temperature
sensor