2005 MERCEDES-BENZ SPRINTER transmission fluid

STATOR
Torque multiplication is achieved by locking the
stator's over-running clutch to its shaft (Fig. 230).
Under stall conditions (the turbine is stationary), the
oil leaving the turbine blades strikes the face of the
stator blades and tries to rotate them in a counter-
clockwise direction. When this happens the over-run-
ning clutch of the stator locks and holds the stator
from rotating. With the stator locked, the oil strikes
the stator blades and is redirected into a ªhelpingº
direction before it enters the impeller. This circula-
tion of oil from impeller to turbine, turbine to stator,
and stator to impeller, can produce a maximum
torque multiplication of about 2.0:1. As the turbine
begins to match the speed of the impeller, the fluid
that was hitting the stator in such as way as to
cause it to lock-up is no longer doing so. In this con-
dition of operation, the stator begins to free wheel
and the converter acts as a fluid coupling.
Fig. 228 Stator Location
1-STATOR
2 - IMPELLER
3 - FLUID FLOW
4 - TURBINEFig. 229 Torque Converter Lock-up Clutch
1 - TURBINE
2 - IMPELLER
3-STATOR
4 - INPUT SHAFT
5 - STATOR SHAFT
6 - PISTON
7 - COVER SHELL
8 - INTERNALLY TOOTHED DISC CARRIER
9 - CLUTCH PLATE SET
10 - EXTERNALLY TOOTHED DISC CARRIER
Fig. 230 Stator Operation
1 - DIRECTION STATOR WILL FREE WHEEL DUE TO OIL
PUSHING ON BACKSIDE OF VANES
2 - FRONT OF ENGINE
3 - INCREASED ANGLE AS OIL STRIKES VANES
4 - DIRECTION STATOR IS LOCKED UP DUE TO OIL PUSHING
AGAINST STATOR VANES
VAAUTOMATIC TRANSMISSION - NAG1 21 - 145
TORQUE CONVERTER (Continued)

TORQUE CONVERTER CLUTCH (TCC)
In a standard torque converter, the impeller and
turbine are rotating at about the same speed and the
stator is freewheeling, providing no torque multipli-
cation. By applying the turbine's piston and friction
material (Fig. 231) to the front cover, a total con-
verter engagement can be obtained. The result of this
engagement is a direct 1:1 mechanical link between
the engine and the transmission.
The clutch can be engaged in second, third, fourth,
and fifth gear ranges.
The TCM controls the torque converter by way of
internal logic software. The programming of the soft-
ware provides the TCM with control over the torque
converter solenoid. There are four output logic states
that can be applied as follows:
²No EMCC
²Partial EMCC
²Full EMCC
²Gradual-to-no EMCCNO EMCC
Under No EMCC conditions, the TCC Solenoid is
OFF. There are several conditions that can result in
NO EMCC operations. No EMCC can be initiated
due to a fault in the transmission or because the
TCM does not see the need for EMCC under current
driving conditions.
PARTIAL EMCC
Partial EMCC operation modulates the TCC Sole-
noid (duty cycle) to obtain partial torque converter
clutch application. Partial EMCC operation is main-
tained until Full EMCC is called for and actuated.
During Partial EMCC some slip does occur. Partial
EMCC will usually occur at low speeds, low load and
light throttle situations.
FULL EMCC
During Full EMCC operation, the TCM increases
the TCC Solenoid duty cycle to full ON after Partial
EMCC control brings the engine speed within the
desired slip range of transmission input speed rela-
tive to engine rpm.
GRADUAL-TO-NO EMCC
This operation is to soften the change from Full or
Partial EMCC to No EMCC. This is done at mid-
throttle by decreasing the TCC Solenoid duty cycle.
REMOVAL
(1) Remove transmission and torque converter
from vehicle.
(2) Place a suitable drain pan under the converter
housing end of the transmission.
CAUTION: Verify that transmission is secure on the
lifting device or work surface, the center of gravity
of the transmission will shift when the torque con-
verter is removed creating an unstable condition.
The torque converter is a heavy unit. Use caution
when separating the torque converter from the
transmission.
(3) Pull the torque converter forward until the cen-
ter hub clears the oil pump seal.
(4) Separate the torque converter from the trans-
mission.
INSTALLATION
Check converter hub and drive flats for sharp
edges, burrs, scratches, or nicks. Polish the hub and
flats with 320/400 grit paper or crocus cloth if neces-
sary. The hub must be smooth to avoid damaging the
pump seal at installation.
(1) Lubricate oil pump seal lip with transmission
fluid.
Fig. 231 Torque Converter Lock-up Clutch
1 - TURBINE
2 - IMPELLER
3-STATOR
4 - INPUT SHAFT
5 - STATOR SHAFT
6 - PISTON
7 - COVER SHELL
8 - INTERNALLY TOOTHED DISC CARRIER
9 - CLUTCH PLATE SET
10 - EXTERNALLY TOOTHED DISC CARRIER
21 - 146 AUTOMATIC TRANSMISSION - NAG1VA
TORQUE CONVERTER (Continued)

(2) Place torque converter in position on transmis-
sion.
CAUTION: Do not damage oil pump seal or con-
verter hub while inserting torque converter into the
front of the transmission.
(3) Align torque converter to oil pump seal open-
ing.
(4) Insert torque converter hub into oil pump.
(5) While pushing torque converter inward, rotate
converter until converter is fully seated in the oil
pump gears.
(6) Check converter seating with a scale and
straightedge (Fig. 232). Surface of converter lugs
should be at least 19 mm (3/4 in.) to rear of straight-
edge when converter is fully seated.
(7) If necessary, temporarily secure converter with
C-clamp attached to the converter housing.
(8) Install the transmission in the vehicle.
(9) Fill the transmission with the recommended
fluid.
TORQUE CONVERTER HUB
SEAL
REMOVAL
(1) Remove the torque converter (Refer to 21 -
TRANSMISSION/AUTOMATIC - NAG1/TORQUE
CONVERTER - REMOVAL).
(2) Remove the torque converter hub seal with
suitable screw and slide hammer.
INSTALLATION
(1) Position the torque converter hub seal (Fig.
233) over the input shaft and against the transmis-
sion oil pump.
(2) Using Seal Installer 8902A (Fig. 234), install a
new torque converter hub seal.
(3) Install the torque converter (Refer to 21 -
TRANSMISSION/AUTOMATIC - NAG1/TORQUE
CONVERTER - INSTALLATION).
Fig. 232 Torque Converter Installation Depth
1 - TORQUE CONVERTER
2 - TRANSMISSION HOUSING
Fig. 233 Position Torque Converter Hub Seal
1 - TORQUE CONVERTER HUB SEAL
2 - INPUT SHAFT
Fig. 234 Install Torque Converter Hub Seal
1 - OIL PUMP
2 - SEAL INSTALLER 8902A
VAAUTOMATIC TRANSMISSION - NAG1 21 - 147
TORQUE CONVERTER (Continued)

INDEX
ABS INDICATOR - DESCRIPTION..........8J-9
ABS INDICATOR - OPERATION...........8J-9
A/C COMPRESSOR - DESCRIPTION......24-49
A/C COMPRESSOR - INSTALLATION......24-51
A/C COMPRESSOR - OPERATION........24-49
A/C COMPRESSOR - REMOVAL.........24-50
A/C COMPRESSOR CLUTCH -
DESCRIPTION........................24-8
A/C COMPRESSOR CLUTCH -
OPERATION..........................24-8
A/C CONDENSER - DESCRIPTION........24-52
A/C CONDENSER - INSTALLATION.......24-52
A/C CONDENSER - OPERATION..........24-52
A/C CONDENSER - REMOVAL...........24-52
A/C DISCHARGE LINE - INSTALLATION . . . 24-54
A/C DISCHARGE LINE - REMOVAL.......24-53
A/C EVAPORATOR - DESCRIPTION.......24-54
A/C EVAPORATOR - INSTALLATION......24-55
A/C EVAPORATOR - OPERATION.........24-54
A/C EVAPORATOR - REMOVAL..........24-55
A/C EXPANSION VALVE - DESCRIPTION . . . 24-55
A/C EXPANSION VALVE - DIAGNOSIS
AND TESTING.......................24-56
A/C EXPANSION VALVE - INSTALLATION . . 24-56
A/C EXPANSION VALVE - OPERATION.....24-55
A/C EXPANSION VALVE - REMOVAL.......24-56
A/C HEATER CONTROL - DESCRIPTION . . . 24-12
A/C HEATER CONTROL - INSTALLATION . . . 24-13
A/C HEATER CONTROL - OPERATION.....24-12
A/C HEATER CONTROL - REMOVAL......24-12
A/C HOUSING - INSTALLATION, REAR....24-41
A/C HOUSING - REMOVAL, REAR........24-40
A/C PERFORMANCE TEST - DIAGNOSIS
AND TESTING........................24-3
A/C PRESSURE TRANSDUCER -
DESCRIPTION.......................24-13
A/C PRESSURE TRANSDUCER -
DIAGNOSIS AND TESTING.............24-13
A/C PRESSURE TRANSDUCER -
INSTALLATION.......................24-14
A/C PRESSURE TRANSDUCER -
OPERATION.........................24-13
A/C PRESSURE TRANSDUCER -
REMOVAL..........................24-14
A/C SYSTEM, SPECIFICATIONS...........24-5
ACCELERATOR PEDAL POSITION
SENSOR - DESCRIPTION...............14-17
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING.........................7-5
ACCESSORY SWITCH BEZEL -
INSTALLATION.......................23-54
ACCESSORY SWITCH BEZEL - REMOVAL . . 23-54
ACTUATOR - DESCRIPTION,
RECIRCULATION DOOR................24-20
ACTUATOR - INSTALLATION, INSIDE
HANDLE.......................23-34,23-37
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-21
ACTUATOR - OPERATION,
RECIRCULATION DOOR................24-20
ACTUATOR - REMOVAL, INSIDE HANDLE . 23-34,
23-37
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-21
ADAPTATION - STANDARD PROCEDURE,
TCM................................8E-8
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE................7-11
ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING..................7-11
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP.....................8O-34
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP.....................8O-33
ADJUSTERS - FRONT - INSTALLATION,
SEAT ..............................23-78
ADJUSTERS - FRONT - REMOVAL, SEAT . . 23-78
AFTER A SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE.................8O-6
AIR CLEANER ELEMENT - INSTALLATION . . 9-20
AIR CLEANER ELEMENT - REMOVAL
......9-20
AIR CLEANER HOUSING - INSTALLATION
. . 9-20
AIR CLEANER HOUSING - REMOVAL
......9-20
AIR CONDITIONER - DESCRIPTION,
HEATER
.............................24-1
AIR CONDITIONER - OPERATION,
HEATER
.............................24-2AIR COOLER AND PLUMBING -
CLEANING, CHARGE...................11-5
AIR COOLER AND PLUMBING -
DESCRIPTION, CHARGE................11-4
AIR COOLER AND PLUMBING -
INSPECTION, CHARGE.................11-5
AIR COOLER AND PLUMBING -
INSTALLATION, CHARGE................11-5
AIR COOLER AND PLUMBING -
OPERATION, CHARGE..................11-4
AIR COOLER AND PLUMBING -
REMOVAL, CHARGE...................11-5
AIR COOLER SYSTEM - LEAKS -
DIAGNOSIS AND TESTING, CHARGE.......11-4
AIR FILTER - INSTALLATION.......24-31,24-39
AIR FILTER - REMOVAL..........24-31,24-39
AIR FLOW (MAF) SENSOR -
DESCRIPTION, MANIFOLD.............14-30
AIR FLOW (MAF) SENSOR -
INSTALLATION, MANIFOLD.............14-31
AIR FLOW (MAF) SENSOR - OPERATION,
MANIFOLD..........................14-30
AIR FLOW (MAF) SENSOR - REMOVAL,
MANIFOLD..........................14-31
AIR GAP - STANDARD PROCEDURE,
COMPRESSOR CLUTCH................24-9
AIR IN FUEL SYSTEM - DIAGNOSIS AND
TESTING............................14-2
AIR OUTLET TEMPERATURE SENSOR -
DESCRIPTION.......................24-14
AIR OUTLET TEMPERATURE SENSOR -
INSTALLATION.......................24-15
AIR OUTLET TEMPERATURE SENSOR -
OPERATION.........................24-15
AIR OUTLET TEMPERATURE SENSOR -
REMOVAL..........................24-15
AIR OUTLETS - INSTALLATION..........24-32
AIR OUTLETS - REMOVAL.............24-31
AIR TEMPERATURE SENSOR -
DESCRIPTION, INLET.................14-29
AIR TEMPERATURE SENSOR -
INSTALLATION, INLET.................14-30
AIR TEMPERATURE SENSOR -
OPERATION, INLET...................14-29
AIR TEMPERATURE SENSOR -
REMOVAL, INLET....................14-30
AIRBAG - DESCRIPTION, DRIVER........8O-16
AIRBAG - DESCRIPTION, PASSENGER....8O-23
AIRBAG - INSTALLATION, DRIVER.......8O-18
AIRBAG - INSTALLATION, PASSENGER . . . 8O-26
AIRBAG - OPERATION, DRIVER.........8O-17
AIRBAG - OPERATION, PASSENGER......8O-24
AIRBAG - REMOVAL, DRIVER...........8O-17
AIRBAG - REMOVAL, PASSENGER.......8O-24
AIRBAG BRACKET - INSTALLATION,
PASSENGER........................8O-27
AIRBAG BRACKET - REMOVAL,
PASSENGER........................8O-27
AIRBAG CONTROL MODULE -
DESCRIPTION........................8O-8
AIRBAG CONTROL MODULE -
INSTALLATION......................8O-11
AIRBAG CONTROL MODULE -
OPERATION..........................8O-9
AIRBAG CONTROL MODULE - REMOVAL . . 8O-10
AIRBAG INDICATOR - DESCRIPTION......8J-10
AIRBAG INDICATOR - OPERATION.......8J-10
ALB CONTROLLER - INSTALLATION
.......5-15
ALB CONTROLLER - REMOVAL
...........5-15
ALB LEVER - INSTALLATION
.............5-15
ALB LEVER - REMOVAL
................5-15
ALIGNMENT - DESCRIPTION, WHEEL
......2-17
ALIGNMENT - SPECIFICATIONS, WHEEL
....2-19
ALUMINUM THREAD REPAIR -
STANDARD PROCEDURE
...............21-27
AMBIENT TEMPERATURE INDICATOR -
DESCRIPTION
.......................8J-11
AMBIENT TEMPERATURE INDICATOR -
OPERATION
.........................8J-11
AMBIENT TEMPERATURE SENSOR -
DESCRIPTION
.......................24-15
AMBIENT TEMPERATURE SENSOR -
INSTALLATION
.......................24-16
AMBIENT TEMPERATURE SENSOR -
OPERATION
.........................24-15
AMBIENT TEMPERATURE SENSOR -
REMOVAL
..........................24-15ANTENNA BODY & CABLE -
INSTALLATION.......................8A-1
ANTENNA BODY & CABLE - REMOVAL.....8A-1
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL..................8A-2
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL..................8A-1
ANTILOCK BRAKE - DESCRIPTION,
CONTROLLER........................8E-3
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER........................8E-3
ANTILOCK BRAKE - REMOVAL,
CONTROLLER........................8E-3
A-PILLAR TRIM - INSTALLATION........23-68
A-PILLAR TRIM - REMOVAL............23-67
ARM - DESCRIPTION, WIPER...........8R-13
ARM - INSTALLATION, CENTER ROLLER . . 23-38
ARM - INSTALLATION, LOWER CONTROL . . . 2-6
ARM - INSTALLATION, LOWER ROLLER . . . 23-38
ARM - INSTALLATION, UPPER ROLLER . . . 23-37
ARM - INSTALLATION, WIPER..........8R-14
ARM - OPERATION, WIPER............8R-14
ARM - REMOVAL, CENTER ROLLER......23-37
ARM - REMOVAL, LOWER CONTROL.......2-6
ARM - REMOVAL, LOWER ROLLER......23-38
ARM - REMOVAL, UPPER ROLLER.......23-37
ARM - REMOVAL, WIPER..............8R-14
ARMREST - INSTALLATION.............23-76
ARMREST - REMOVAL................23-76
ASH RECEIVER - INSTALLATION.........23-55
ASH RECEIVER - REMOVAL............23-55
ASH RECEIVER/CIGAR LIGHTER LAMP
UNIT - INSTALLATION.................8L-27
ASH RECEIVER/CIGAR LIGHTER LAMP
UNIT - REMOVAL....................8L-27
ASSIST HANDLE - INSTALLATION........23-68
ASSIST HANDLE - REMOVAL...........23-68
AUDIO, SPECIAL TOOLS................8A-1
AUTOMATIC TRANSMISSION -
DIAGNOSIS AND TESTING........21-23,21-24
AUTOMATIC TRANSMISSION - NAG1 -
DESCRIPTION........................21-2
AUTOMATIC TRANSMISSION - NAG1 -
OPERATION..........................21-4
AUTOMATIC TRANSMISSION - SPECIAL
TOOLS, NAG1.......................21-69
AUTOMATIC TRANSMISSION -
SPECIFICATIONS, NAG1...............21-68
AUTOMATIC TRANSMISSION FLUID -
NAG1 - DESCRIPTION...................0-4
AUTOMATIC TRANSMISSION FLUID -
OPERATION...........................0-4
AUXILIARY BATTERY INSTALLATION,
INSTALLATION.......................8F-13
AUXILIARY BATTERY REMOVAL,
REMOVAL..........................8F-13
AXLE - DESCRIPTION...................0-3
AXLE - DESCRIPTION, REAR.............3-10
AXLE - DIAGNOSIS AND TESTING, REAR . . . 3-10
AXLE - INSTALLATION, REAR............3-12
AXLE - OPERATION, REAR..............3-10
AXLE - REMOVAL, REAR................3-11
AXLE - SPECIAL TOOLS, REAR...........3-14
AXLE - SPECIFICATIONS, REAR..........3-13
AXLE BEARINGS/SEALS - INSTALLATION . . . 3-17
AXLE BEARINGS/SEALS - REMOVAL......3-17
AXLE HUB BEARINGS/SEALS -
INSTALLATION........................3-20
AXLE HUB BEARINGS/SEALS - REMOVAL . . 3-20
AXLE SHAFTS - DUAL REAR WHEELS -
INSTALLATION........................3-19
AXLE SHAFTS - DUAL REAR WHEELS -
REMOVAL...........................3-19
AXLE SHAFTS - INSTALLATION...........3-15
AXLE SHAFTS - REMOVAL..............3-15
B1 - ASSEMBLY, HOLDING CLUTCH.....21-113
B1 - DISASSEMBLY, HOLDING CLUTCH . . 21-112
B2 - ASSEMBLY, HOLDING CLUTCH.....21-116
B2 - DISASSEMBLY, HOLDING CLUTCH . . 21-115
BACK - FRONT - INSTALLATION, SEAT....23-77
BACK - FRONT - REMOVAL, SEAT
.......23-77
BACK CUSHION/COVER - REAR -
INSTALLATION, SEAT
.................23-80
BACK CUSHION/COVER - REAR -
REMOVAL, SEAT
.....................23-80
BACK SHIELD - INSTALLATION, REAR
SEAT
..............................23-79
BACK SHIELD - REMOVAL, REAR SEAT
. . . 23-79
VAINDEX 1
Description Group-Page Description Group-Page Description Group-Page

CIRCUIT BREAKER - OPERATION......8W-97-2
CIRCUIT INFORMATION - DESCRIPTION . 8W-01-5
CLAMP PLATES - INSTALLATION,
SPRING..............................2-8
CLAMP PLATES - REMOVAL, SPRING......2-8
CLASSIFICATION - STANDARD
PROCEDURE, INJECTOR...............14-22
CLEARANCE LAMP BULB -
INSTALLATION........................8L-8
CLEARANCE LAMP BULB - REMOVAL.....8L-8
CLEARANCE LAMP UNIT -
INSTALLATION........................8L-9
CLEARANCE LAMP UNIT - REMOVAL......8L-8
CLOCK - DESCRIPTION................8J-13
CLOCK - OPERATION..................8J-14
CLOCKSPRING - DESCRIPTION.........8O-12
CLOCKSPRING - INSTALLATION.........8O-15
CLOCKSPRING - OPERATION...........8O-13
CLOCKSPRING - REMOVAL............8O-14
CLOCKSPRING CENTERING - STANDARD
PROCEDURE........................8O-13
CLOGGED INDICATOR - DESCRIPTION,
FUEL FILTER........................8J-15
CLOGGED INDICATOR - OPERATION,
FUEL FILTER........................8J-15
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-2
CLUSTER - DIAGNOSIS AND TESTING,
INSTRUMENT........................8J-7
CLUSTER - INSTALLATION, INSTRUMENT . . 8J-9
CLUSTER - INSTALLATION, TOP COVER . . . 23-62
CLUSTER - OPERATION, INSTRUMENT.....8J-5
CLUSTER - REMOVAL, INSTRUMENT......8J-7
CLUSTER - REMOVAL, TOP COVER......23-62
CLUSTER BEZEL - INSTALLATION........23-54
CLUSTER BEZEL - REMOVAL...........23-53
CLUTCH - ASSEMBLY, FREEWHEELING . . 21-107
CLUTCH - DESCRIPTION, A/C
COMPRESSOR........................24-8
CLUTCH - DESCRIPTION,
FREEWHEELING.....................21-105
CLUTCH - DISASSEMBLY,
FREEWHEELING.....................21-106
CLUTCH - INSTALLATION, FAN DRIVE
VISCOUS............................7-16
CLUTCH - OPERATION, A/C
COMPRESSOR........................24-8
CLUTCH - OPERATION, FREEWHEELING . . 21-105
CLUTCH - REMOVAL, FAN DRIVE
VISCOUS............................7-16
CLUTCH AIR GAP - STANDARD
PROCEDURE, COMPRESSOR............24-9
CLUTCH B1 - ASSEMBLY, HOLDING.....21-113
CLUTCH B1 - DISASSEMBLY, HOLDING . . 21-112
CLUTCH B2 - ASSEMBLY, HOLDING.....21-116
CLUTCH B2 - DISASSEMBLY, HOLDING . . 21-115
CLUTCH BREAK-IN - STANDARD
PROCEDURE, COMPRESSOR............24-9
CLUTCH COIL - DIAGNOSIS AND
TESTING, COMPRESSOR...............24-12
CLUTCH K1 - ASSEMBLY, DRIVING.......21-75
CLUTCH K1 - DISASSEMBLY, DRIVING....21-74
CLUTCH K2 - ASSEMBLY, DRIVING.......21-78
CLUTCH K2 - DISASSEMBLY, DRIVING....21-76
CLUTCH K3 - ASSEMBLY, DRIVING.......21-80
CLUTCH K3 - DISASSEMBLY, DRIVING....21-80
CLUTCH/COIL - INSPECTION,
COMPRESSOR.......................24-10
CLUTCHES - DESCRIPTION, DRIVING.....21-72
CLUTCHES - DESCRIPTION, HOLDING . . . 21-111
CLUTCHES - OPERATION, DRIVING......21-72
CLUTCHES - OPERATION, HOLDING.....21-112
CODES - SPECIFICATIONS, PAINT........23-74
COIL - DIAGNOSIS AND TESTING,
COMPRESSOR CLUTCH...............24-12
COLUMN OPENING COVER -
INSTALLATION, STEERING.............23-66
COLUMN OPENING COVER - REMOVAL,
STEERING..........................23-66
COMPRESSION TESTING ENGINE -
STANDARD PROCEDURE.................9-3
COMPRESSOR - DESCRIPTION, A/C......24-49
COMPRESSOR - INSTALLATION, A/C
.....24-51
COMPRESSOR - OPERATION, A/C
........24-49
COMPRESSOR - REMOVAL, A/C
.........24-50
COMPRESSOR CLUTCH - DESCRIPTION,
A/C
................................24-8
COMPRESSOR CLUTCH - OPERATION,
A/C
................................24-8COMPRESSOR CLUTCH AIR GAP -
STANDARD PROCEDURE................24-9
COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE................24-9
COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-12
COMPRESSOR CLUTCH/COIL -
INSPECTION........................24-10
COMPRESSOR NOISE - DIAGNOSIS AND
TESTING...........................24-49
CONDENSER - DESCRIPTION, A/C.......24-52
CONDENSER - INSTALLATION, A/C.......24-52
CONDENSER - OPERATION, A/C.........24-52
CONDENSER - REMOVAL, A/C..........24-52
CONDITIONER - DESCRIPTION, HEATER
AND AIR ............................24-1
CONDITIONER - OPERATION, HEATER
AND AIR ............................24-2
CONNECTING FUEL LINES - STANDARD
PROCEDURE, DISCONNECTING...........14-2
CONNECTING ROD - DESCRIPTION,
PISTON.............................9-40
CONNECTING RODS - STANDARD
PROCEDURE, CHECKING AND
REPAIRING..........................9-40
CONNECTOR - INSTALLATION........8W-01-9
CONNECTOR - REMOVAL............8W-01-8
CONNECTOR, GROUND AND SPLICE
INFORMATION - DESCRIPTION........8W-01-5
CONNECTOR/GROUND/SPLICE LOCATION
- DESCRIPTION....................8W-91-1
CONTACT - DESCRIPTION, PARK/
NEUTRAL..........................21-139
CONTACT - OPERATION, PARK/NEUTRAL . 21-140
CONTAMINATION - DIAGNOSIS AND
TESTING, BRAKE FLUID................5-14
CONTAMINATION - DIAGNOSIS AND
TESTING, FLUID....................21-102
CONTINUITY - STANDARD PROCEDURE,
TESTING.........................8W-01-8
CONTROL ARM - INSTALLATION, LOWER . . . 2-6
CONTROL ARM - REMOVAL, LOWER.......2-6
CONTROL INDICATOR - DESCRIPTION,
TRACTION..........................8J-24
CONTROL INDICATOR - OPERATION,
TRACTION..........................8J-24
CONTROL MALFUNCTION INDICATOR -
DESCRIPTION, TRACTION..............8J-25
CONTROL MALFUNCTION INDICATOR -
OPERATION, TRACTION................8J-25
CONTROL MODULE - DESCRIPTION......24-24
CONTROL MODULE - DESCRIPTION,
AIRBAG.............................8O-8
CONTROL MODULE - DESCRIPTION,
ENGINE.............................8E-3
CONTROL MODULE - DESCRIPTION,
TRANSMISSION.......................8E-5
CONTROL MODULE - DIAGNOSIS AND
TESTING...........................24-24
CONTROL MODULE - INSTALLATION.....24-25
CONTROL MODULE - INSTALLATION,
AIRBAG............................8O-11
CONTROL MODULE - INSTALLATION,
ENGINE.............................8E-4
CONTROL MODULE - OPERATION.......24-24
CONTROL MODULE - OPERATION,
AIRBAG.............................8O-9
CONTROL MODULE - OPERATION,
TRANSMISSION.......................8E-5
CONTROL MODULE - REMOVAL.........24-24
CONTROL MODULE - REMOVAL, AIRBAG . 8O-10
CONTROL MODULE - REMOVAL, ENGINE . . . 8E-4
CONTROLLER - INSTALLATION, ALB......5-15
CONTROLLER - REMOVAL, ALB..........5-15
CONTROLLER ANTILOCK BRAKE -
DESCRIPTION........................8E-3
CONTROLLER ANTILOCK BRAKE -
INSTALLATION........................8E-3
CONTROLLER ANTILOCK BRAKE -
REMOVAL...........................8E-3
CONVERTER - DESCRIPTION, TORQUE . . . 21-141
CONVERTER - INSTALLATION, CATALYTIC . . 11-3
CONVERTER - INSTALLATION, TORQUE
. . 21-146
CONVERTER - OPERATION, TORQUE
....21-143
CONVERTER - REMOVAL, CATALYTIC
......11-3
CONVERTER - REMOVAL, TORQUE
......21-146
CONVERTER HUB SEAL - INSTALLATION,
TORQUE
...........................21-147CONVERTER HUB SEAL - REMOVAL,
TORQUE...........................21-147
COOLANT - DESCRIPTION...............7-9
COOLANT - DESCRIPTION, ENGINE........0-1
COOLANT - DESCRIPTION, HOAT..........0-2
COOLANT - STANDARD PROCEDURE,
ADDING ADDITIONAL..................7-11
COOLANT LEVEL SENSOR -
INSTALLATION........................7-13
COOLANT LEVEL SENSOR - REMOVAL.....7-13
COOLANT LOW INDICATOR -
DESCRIPTION.......................8J-14
COOLANT LOW INDICATOR - OPERATION . 8J-14
COOLANT PUMP - DESCRIPTION,
ELECTRIC..........................24-57
COOLANT PUMP - INSTALLATION,
ELECTRIC..........................24-57
COOLANT PUMP - OPERATION,
ELECTRIC..........................24-57
COOLANT PUMP - REMOVAL, ELECTRIC . . 24-57
COOLANT TEMP SENSOR -
DESCRIPTION, ENGINE.................7-14
COOLANT TEMP SENSOR -
INSTALLATION, ENGINE................7-15
COOLANT TEMP SENSOR - REMOVAL,
ENGINE.............................7-14
COOLANT THERMOSTAT -
INSTALLATION, ENGINE................7-16
COOLANT THERMOSTAT - REMOVAL,
ENGINE.............................7-15
COOLER & LINES - INSTALLATION, OIL....9-50
COOLER & LINES - REMOVAL, OIL.......9-50
COOLER AND PLUMBING - CLEANING,
CHARGE AIR.........................11-5
COOLER AND PLUMBING -
DESCRIPTION, CHARGE AIR.............11-4
COOLER AND PLUMBING - INSPECTION,
CHARGE AIR.........................11-5
COOLER AND PLUMBING -
INSTALLATION, CHARGE AIR............11-5
COOLER AND PLUMBING - OPERATION,
CHARGE AIR.........................11-4
COOLER AND PLUMBING - REMOVAL,
CHARGE AIR.........................11-5
COOLER SYSTEM - LEAKS - DIAGNOSIS
AND TESTING, CHARGE AIR.............11-4
COOLER TUBE - INSTALLATION, FLUID . . . 19-14
COOLER TUBE - INSTALLATION, RETURN
HOSE FROM GEAR TO................19-15
COOLER TUBE - INSTALLATION, RETURN
LINE FROM PUMP TO.................19-15
COOLER TUBE - REMOVAL, FLUID.......19-14
COOLER TUBE - REMOVAL, RETURN
HOSE FROM GEAR TO................19-15
COOLER TUBE - REMOVAL, RETURN
LINE FROM PUMP TO.................19-15
COOLING SYSTEM - DIAGNOSIS AND
TESTING.............................7-2
COOLING SYSTEM - OPERATION..........7-1
COOLING SYSTEM - STANDARD
PROCEDURE, DRAINING................7-12
COOLING SYSTEM - STANDARD
PROCEDURE, REFILLING................7-12
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING........................7-10
COOLING SYSTEM REQUIREMENTS -
DESCRIPTION........................24-1
CORE - DESCRIPTION, HEATER.........24-57
CORE - INSTALLATION, HEATER.........24-58
CORE - OPERATION, HEATER...........24-57
CORE - REMOVAL, HEATER............24-58
CORE AND OIL GALLERY PLUGS -
STANDARD PROCEDURE, REPLACING
ENGINE.............................9-34
COVER - CLUSTER - INSTALLATION, TOP . 23-62
COVER - CLUSTER - REMOVAL, TOP.....23-62
COVER - INSTALLATION, CYLINDER
HEAD FRONT.........................9-26
COVER - INSTALLATION, ENGINE..........9-7
COVER - INSTALLATION, STEERING
COLUMN OPENING...................23-66
COVER - INSTALLATION, TIMING CHAIN
. . . 9-60
COVER - INSTALLATION, TOP
...........23-65
COVER - REMOVAL, CYLINDER HEAD
FRONT
..............................9-23
COVER - REMOVAL, ENGINE
..............9-4
COVER - REMOVAL, STEERING COLUMN
OPENING
...........................23-66
4 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

DUAL REAR WHEEL INSTALLATION -
STANDARD PROCEDURE...............22-12
DUAL REAR WHEELS - INSTALLATION,
AXLE SHAFTS........................3-19
DUAL REAR WHEELS - REMOVAL, AXLE
SHAFTS.............................3-19
DUCTS - INSTALLATION, DEFROSTER....24-33
DUCTS - INSTALLATION, FLOOR
DISTRIBUTION.......................24-34
DUCTS - INSTALLATION, INSTRUMENT
PANEL.............................24-38
DUCTS - REMOVAL, DEFROSTER........24-33
DUCTS - REMOVAL, FLOOR
DISTRIBUTION.......................24-33
DUCTS - REMOVAL, INSTRUMENT
PANEL.............................24-37
EFFECTS OF INCORRECT FLUID LEVEL -
DIAGNOSIS AND TESTING............21-102
ELECTRIC COOLANT PUMP -
DESCRIPTION.......................24-57
ELECTRIC COOLANT PUMP -
INSTALLATION.......................24-57
ELECTRIC COOLANT PUMP - OPERATION . 24-57
ELECTRIC COOLANT PUMP - REMOVAL . . . 24-57
ELECTRICAL - DESCRIPTION............5-29
ELECTRICAL - OPERATION..............5-29
ELECTROHYDRAULIC UNIT - ASSEMBLY . . 21-95
ELECTROHYDRAULIC UNIT -
DESCRIPTION.......................21-82
ELECTROHYDRAULIC UNIT -
DISASSEMBLY.......................21-92
ELECTROHYDRAULIC UNIT -
INSTALLATION......................21-100
ELECTROHYDRAULIC UNIT - OPERATION . . 21-87
ELECTROHYDRAULIC UNIT - REMOVAL . . . 21-92
ELECTROLYTE LEVEL - STANDARD
PROCEDURE, CHECKING BATTERY.......8F-12
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE DEVICES - STANDARD
PROCEDURE......................8W-01-7
ELEMENT - DESCRIPTION, HEATED SEAT . . 8G-3
ELEMENT - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8G-3
ELEMENT - INSTALLATION, AIR
CLEANER............................9-20
ELEMENT - OPERATION, HEATED SEAT....8G-3
ELEMENT - REMOVAL, AIR CLEANER......9-20
END - DIAGNOSIS AND TESTING, OUTER
TIE ROD............................19-10
END - INSTALLATION, TIE ROD.........19-11
END - REMOVAL, TIE ROD.............19-11
ENGINE - DESCRIPTION.................9-2
ENGINE - DESCRIPTION, FUEL
REQUIREMENTS - DIESEL...............0-1
ENGINE - DIAGNOSIS AND TESTING,
DIESEL.............................11-2
ENGINE - STANDARD PROCEDURE,
COMPRESSION TESTING................9-3
ENGINE BLOCK HEATER - INSTALLATION . . . 7-14
ENGINE BLOCK HEATER - REMOVAL......7-14
ENGINE CONTROL MODULE -
DESCRIPTION........................8E-3
ENGINE CONTROL MODULE -
INSTALLATION........................8E-4
ENGINE CONTROL MODULE - REMOVAL . . . 8E-4
ENGINE COOLANT - DESCRIPTION.........0-1
ENGINE COOLANT TEMP SENSOR -
DESCRIPTION........................7-14
ENGINE COOLANT TEMP SENSOR -
INSTALLATION........................7-15
ENGINE COOLANT TEMP SENSOR -
REMOVAL...........................7-14
ENGINE COOLANT THERMOSTAT -
INSTALLATION........................7-16
ENGINE COOLANT THERMOSTAT -
REMOVAL...........................7-15
ENGINE CORE AND OIL GALLERY PLUGS
- STANDARD PROCEDURE, REPLACING....9-34
ENGINE COVER - INSTALLATION..........9-7
ENGINE COVER - REMOVAL
..............9-4
ENGINE CRADLE CROSSMEMBER -
INSTALLATION
........................13-8
ENGINE CRADLE CROSSMEMBER -
REMOVAL
...........................13-6
ENGINE OIL - DIESEL ENGINES -
DESCRIPTION
.........................0-3
ENGINE TEMPERATURE GAUGE -
DESCRIPTION
.......................8J-15ENGINE TEMPERATURE GAUGE -
OPERATION.........................8J-15
ENGINES - DESCRIPTION, ENGINE OIL -
DIESEL..............................0-3
ENTRY MODULE - DESCRIPTION,
SENTRY KEY REMOTE.................8Q-2
ENTRY MODULE - INSTALLATION,
SENTRY KEY REMOTE.................8Q-4
ENTRY MODULE - OPERATION, SENTRY
KEY REMOTE........................8Q-3
ENTRY MODULE - REMOVAL, SENTRY
KEY REMOTE........................8Q-3
ENTRY TRANSMITTER - DESCRIPTION,
REMOTE KEYLESS....................8N-2
ENTRY/EXIT LAMP BULB -
INSTALLATION.......................8L-32
ENTRY/EXIT LAMP BULB - REMOVAL.....8L-31
ENTRY/EXIT LAMP UNIT - INSTALLATION . 8L-32
ENTRY/EXIT LAMP UNIT - REMOVAL.....8L-32
EQUIPMENT - STANDARD PROCEDURE,
REFRIGERANT SYSTEM SERVICE........24-46
EVACUATE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-47
EVAPORATOR - DESCRIPTION, A/C.......24-54
EVAPORATOR - INSTALLATION, A/C......24-55
EVAPORATOR - INSTALLATION, REAR....24-61
EVAPORATOR - OPERATION, A/C........24-54
EVAPORATOR - REMOVAL, A/C..........24-55
EVAPORATOR - REMOVAL, REAR........24-60
EVAPORATOR TEMPERATURE SENSOR -
DESCRIPTION....................24-17,24-25
EVAPORATOR TEMPERATURE SENSOR -
DIAGNOSIS AND TESTING.............24-26
EVAPORATOR TEMPERATURE SENSOR -
INSTALLATION..................24-18,24-26
EVAPORATOR TEMPERATURE SENSOR -
OPERATION....................24-18,24-26
EVAPORATOR TEMPERATURE SENSOR -
REMOVAL.....................24-18,24-26
EXHAUST MANIFOLD - INSTALLATION.....9-59
EXHAUST MANIFOLD - REMOVAL.........9-59
EXHAUST PIPE - INSTALLATION..........11-3
EXHAUST PIPE - REMOVAL.............11-3
EXHAUST TUBE - INSTALLATION........24-73
EXHAUST TUBE - REMOVAL............24-73
EXPANSION VALVE - DESCRIPTION, A/C . . 24-55
EXPANSION VALVE - DIAGNOSIS AND
TESTING, A/C.......................24-56
EXPANSION VALVE - INSTALLATION, A/C . . 24-56
EXPANSION VALVE - INSTALLATION,
REAR..............................24-63
EXPANSION VALVE - OPERATION, A/C....24-55
EXPANSION VALVE - REMOVAL, A/C.....24-56
EXPANSION VALVE - REMOVAL, REAR....24-62
EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-3
EXTERIOR - SPECIFICATIONS,
LAMPS/LIGHTING.....................8L-5
EXTERIOR HANDLE - INSTALLATION.....23-16,
23-33,23-36
EXTERIOR HANDLE - REMOVAL . . . 23-16,23-32,
23-36
FAN - INSTALLATION, RADIATOR.........7-13
FAN - REMOVAL, RADIATOR.............7-13
FAN DRIVE VISCOUS CLUTCH -
INSTALLATION........................7-16
FAN DRIVE VISCOUS CLUTCH -
REMOVAL...........................7-16
FASCIA - INSTALLATION, FRONT.........13-2
FASCIA - INSTALLATION, REAR..........13-3
FASCIA - REMOVAL, FRONT.............13-2
FASCIA - REMOVAL, REAR..............13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-2
FASTENER USAGE - DESCRIPTION......Intro.-5
FILL - STANDARD PROCEDURE, DRAIN....3-11
FILL - STANDARD PROCEDURE,
TRANSMISSION.....................21-103
FILL AND BLEED PROCEDURE,
STANDARD PROCEDURE - POWER
STEERING PUMP
.....................19-14
FILL DOOR - INSTALLATION, FUEL
.......23-47
FILL DOOR - REMOVAL, FUEL
..........23-47
FILL/CHECK LOCATIONS - INSPECTION,
FLUID
...............................0-4
FILTER - DESCRIPTION, FLUID
.........21-101FILTER - DESCRIPTION, FUEL............14-5
FILTER - INSTALLATION, AIR......24-31,24-39
FILTER - INSTALLATION, FUEL...........14-6
FILTER - INSTALLATION, OIL............9-51
FILTER - OPERATION, FLUID...........21-101
FILTER - OPERATION, FUEL.............14-5
FILTER - REMOVAL, AIR..........24-31,24-39
FILTER - REMOVAL, FUEL...............14-5
FILTER - REMOVAL, OIL................9-51
FILTER - STANDARD PROCEDURES,
DRAINING WATER FROM FUEL...........14-2
FILTER CLOGGED INDICATOR -
DESCRIPTION, FUEL..................8J-15
FILTER CLOGGED INDICATOR -
OPERATION, FUEL....................8J-15
FINESSE SANDING/BUFFING & POLISH -
DESCRIPTION.......................23-75
FINISH - DESCRIPTION, BASECOAT/
CLEARCOAT.........................23-74
FITTING - STANDARD PROCEDURE,
PISTON RING........................9-46
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED.....................5-8
FLARING - STANDARD PROCEDURE, ISO....5-8
FLOOR DISTRIBUTION DUCTS -
INSTALLATION.......................24-34
FLOOR DISTRIBUTION DUCTS -
REMOVAL..........................24-33
FLOOR MATS - INSTALLATION, CARPETS . 23-70
FLOOR MATS - REMOVAL, CARPETS.......23-69
FLOW (MAF) SENSOR - DESCRIPTION,
MANIFOLD AIR......................14-30
FLOW (MAF) SENSOR - INSTALLATION,
MANIFOLD AIR......................14-31
FLOW (MAF) SENSOR - OPERATION,
MANIFOLD AIR......................14-30
FLOW (MAF) SENSOR - REMOVAL,
MANIFOLD AIR......................14-31
FLUID - DESCRIPTION, BRAKE............0-3
FLUID - DESCRIPTION, POWER
STEERING............................0-3
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT..................21-102
FLUID - NAG1 - DESCRIPTION,
AUTOMATIC TRANSMISSION.............0-4
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-4
FLUID AND FILTER - DESCRIPTION.....21-101
FLUID AND FILTER - OPERATION.......21-101
FLUID CAPACITIES - SPECIFICATIONS......0-4
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING......................21-102
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-14
FLUID COOLER TUBE - INSTALLATION....19-14
FLUID COOLER TUBE - REMOVAL.......19-14
FLUID FILL/CHECK LOCATIONS -
INSPECTION..........................0-4
FLUID INDICATOR - DESCRIPTION,
WASHER...........................8J-27
FLUID INDICATOR - OPERATION,
WASHER...........................8J-27
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT......21-102
FLUID LEVEL - STANDARD PROCEDURE,
BRAKE..............................5-14
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-7
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-8
FLUID RESERVOIR - INSTALLATION.......5-15
FLUID RESERVOIR - REMOVAL..........5-15
FLUID, SPECIFICATIONS - BRAKE.........5-14
FLUID/FILTER SERVICE - STANDARD
PROCEDURE.......................21-104
FLUSH - SPECIFICATIONS, GAP.........23-88
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-13
FLYWHEEL - REMOVAL.................9-39
FOG LAMP BULB - INSTALLATION.......8L-10
FOG LAMP BULB - REMOVAL...........8L-10
FOG LAMP RELAY - INSTALLATION......8L-11
FOG LAMP RELAY - REMOVAL..........8L-10
FOG LAMP SWITCH - INSTALLATION
.....8L-12
FOG LAMP SWITCH - REMOVAL
.........8L-11
FRAME DIMENSIONS - SPECIFICATIONS
. . . 13-4
FREEWHEELING CLUTCH - ASSEMBLY
. . . 21-107
FREEWHEELING CLUTCH - DESCRIPTION
. 21-105
6 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

MODULE - DESCRIPTION, SENTRY KEY
REMOTE ENTRY......................8Q-2
MODULE - DESCRIPTION,
TRANSMISSION CONTROL..............8E-5
MODULE - DIAGNOSIS AND TESTING,
CENTRAL TIMER......................8E-2
MODULE - DIAGNOSIS AND TESTING,
CONTROL..........................24-24
MODULE - INSTALLATION, AIRBAG
CONTROL..........................8O-11
MODULE - INSTALLATION, CENTRAL
TIMER..............................8E-2
MODULE - INSTALLATION, CONTROL.....24-25
MODULE - INSTALLATION, ENGINE
CONTROL...........................8E-4
MODULE - INSTALLATION, FUEL TANK....14-14
MODULE - INSTALLATION, SECURITY
SYSTEM............................8Q-2
MODULE - INSTALLATION, SENTRY KEY
REMOTE ENTRY......................8Q-4
MODULE - OPERATION, AIRBAG
CONTROL...........................8O-9
MODULE - OPERATION, CENTRAL TIMER . . 8E-2
MODULE - OPERATION, CONTROL.......24-24
MODULE - OPERATION, SENTRY KEY
REMOTE ENTRY......................8Q-3
MODULE - OPERATION, TRANSMISSION
CONTROL...........................8E-5
MODULE - REMOVAL, AIRBAG CONTROL . 8O-10
MODULE - REMOVAL, CENTRAL TIMER....8E-2
MODULE - REMOVAL, CONTROL........24-24
MODULE - REMOVAL, ENGINE CONTROL . . . 8E-4
MODULE - REMOVAL, FUEL TANK.......14-13
MODULE - REMOVAL, SECURITY
SYSTEM............................8Q-2
MODULE - REMOVAL, SENTRY KEY
REMOTE ENTRY......................8Q-3
MOTOR - DESCRIPTION, WIPER........8R-19
MOTOR - DIAGNOSIS AND TESTING,
STARTER ...........................8F-29
MOTOR - DIESEL - SPECIFICATIONS,
STARTER ...........................8F-29
MOTOR - INSTALLATION, BLOWER . 24-33,24-40
MOTOR - INSTALLATION, DOOR LOCK....8N-1
MOTOR - INSTALLATION, HEADLAMP
LEVELING..........................8L-16
MOTOR - INSTALLATION, STARTER......8F-31
MOTOR - INSTALLATION, WIPER........8R-19
MOTOR - OPERATION, WIPER..........8R-19
MOTOR - REMOVAL, BLOWER.....24-32,24-39
MOTOR - REMOVAL, DOOR LOCK........8N-1
MOTOR - REMOVAL, HEADLAMP
LEVELING..........................8L-15
MOTOR - REMOVAL, STARTER..........8F-30
MOTOR - REMOVAL, WINDOW...........8N-5
MOTOR - REMOVAL, WIPER...........8R-19
MOTOR RELAY - DESCRIPTION,
BLOWER...........................24-23
MOTOR RELAY - DESCRIPTION,
STARTER ...........................8F-31
MOTOR RELAY - DIAGNOSIS AND
TESTING, BLOWER...................24-24
MOTOR RELAY - INSTALLATION,
BLOWER...........................24-24
MOTOR RELAY - INSTALLATION,
STARTER
...........................8F-32
MOTOR RELAY - OPERATION, BLOWER
. . . 24-23
MOTOR RELAY - REMOVAL, BLOWER
....24-24
MOTOR RELAY - REMOVAL, STARTER
....8F-31
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER
...............24-16
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, BLOWER
...............24-16
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER
..............24-17
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER
...........................24-16
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER
...........................24-16
MOTOR SWITCH - DESCRIPTION,
BLOWER
......................24-17,24-22
MOTOR SWITCH - DIAGNOSIS AND
TESTING, BLOWER
..............24-17,24-23
MOTOR SWITCH - INSTALLATION,
BLOWER
...........................24-23
MOTOR SWITCH - OPERATION, BLOWER
. 24-17,
24-22MOTOR SWITCH - REMOVAL, BLOWER . . 24-17,
24-23
MOUNT - INSTALLATION, LEFT...........9-49
MOUNT - INSTALLATION, RIGHT.........9-49
MOUNT - REMOVAL, LEFT..............9-49
MOUNT - REMOVAL, RIGHT.............9-49
MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER HIGH...........8L-7
MOUNTED STOP LAMP BULB -
REMOVAL, CENTER HIGH...............8L-7
MOUNTED STOP LAMP UN -
INSTALLATION, CENTER HIGH...........8L-8
MOUNTED STOP LAMP UN - REMOVAL,
CENTER HIGH........................8L-8
MOUNTING - STANDARD PROCEDURE,
MATCH .............................22-2
MULTI-FUNCTION INDICATOR -
DESCRIPTION.......................8J-20
MULTI-FUNCTION INDICATOR -
OPERATION.........................8J-21
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-20
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-19
NAG1 - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................21-2
NAG1 - DESCRIPTION, AUTOMATIC
TRANSMISSION FLUID..................0-4
NAG1 - OPERATION, AUTOMATIC
TRANSMISSION.......................21-4
NAG1 AUTOMATIC TRANSMISSION -
SPECIAL TOOLS.....................21-69
NAG1 AUTOMATIC TRANSMISSION -
SPECIFICATIONS.....................21-68
NOISE - DIAGNOSIS AND TESTING,
COMPRESSOR.......................24-49
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-8
NON-DEPLOYED SUPPLEMENTAL
RESTRAINTS - STANDARD
PROCEDURE, HANDLING...............8O-6
NOZZLE - DESCRIPTION, WASHER.......8R-9
NOZZLE - INSTALLATION, WASHER.......8R-9
NOZZLE - OPERATION, WASHER.........8R-9
NOZZLE - REMOVAL, WASHER...........8R-9
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION....................Intro.-1
ODOMETER - DESCRIPTION............8J-21
ODOMETER - OPERATION..............8J-22
OIL - DESCRIPTION, REFRIGERANT......24-65
OIL - DIESEL ENGINES - DESCRIPTION,
ENGINE..............................0-3
OIL - OPERATION, REFRIGERANT........24-65
OIL COOLER & LINES - INSTALLATION....9-50
OIL COOLER & LINES - REMOVAL........9-50
OIL FILTER - INSTALLATION.............9-51
OIL FILTER - REMOVAL.................9-51
OIL GALLERY PLUGS - STANDARD
PROCEDURE, REPLACING ENGINE
CORE...............................9-34
OIL JET - DESCRIPTION................9-51
OIL JET - INSTALLATION...............9-51
OIL JET - REMOVAL...................9-51
OIL LEVEL - STANDARD PROCEDURE,
CHECK............................21-102
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-65
OIL LEVEL INDICATOR - DESCRIPTION,
LOW...............................8J-18
OIL LEVEL INDICATOR - OPERATION,
LOW...............................8J-18
OIL PAN - INSTALLATION...............9-52
OIL PAN - REMOVAL...................9-52
OIL PUMP - ASSEMBLY..............21-121
OIL PUMP - DESCRIPTION............21-120
OIL PUMP - DISASSEMBLY............21-120
OIL PUMP - OPERATION..............21-120
OIL PUMP CHAIN - INSTALLATION........9-54
OIL PUMP CHAIN - REMOVAL
...........9-53
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT
........................9-38
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT
........................9-38
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT
........................9-37
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT
........................9-37OIL SEPARATOR - INSTALLATION.........9-50
OIL SEPARATOR - REMOVAL............9-50
OIL TEMPERATURE SENSOR -
DESCRIPTION........................9-56
OIL TEMPERATURE SENSOR -
INSTALLATION........................9-57
OIL TEMPERATURE SENSOR -
OPERATION..........................9-56
OIL TEMPERATURE SENSOR - REMOVAL . . . 9-57
OPEN-CIRCUIT VOLTAGE TEST -
STANDARD PROCEDURE...............8F-10
OPENING COVER - INSTALLATION,
STEERING COLUMN..................23-66
OPENING COVER - REMOVAL, STEERING
COLUMN...........................23-66
OPENING DIMENSIONS -
SPECIFICATIONS.....................23-90
OPENING SEALS - INSTALLATION, DOOR . . 23-87
OPENING SEALS - REMOVAL, DOOR.....23-87
OUTBOARD - INSTALLATION...........8O-31
OUTBOARD - REMOVAL...............8O-30
OUTER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR...........23-87
OUTER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR..............23-87
OUTER TIE ROD END - DIAGNOSIS AND
TESTING...........................19-10
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-1
OUTLET - DESCRIPTION, POWER......8W-97-3
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER..........................8W-97-4
OUTLET - INSTALLATION, POWER.....8W-97-4
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER.......8W-97-4
OUTLET - REMOVAL, CIGAR LIGHTER . . 8W-97-2
OUTLET - REMOVAL, POWER.........8W-97-4
OUTLET TEMPERATURE SENSOR -
DESCRIPTION, AIR...................24-14
OUTLET TEMPERATURE SENSOR -
INSTALLATION, AIR...................24-15
OUTLET TEMPERATURE SENSOR -
OPERATION, AIR.....................24-15
OUTLET TEMPERATURE SENSOR -
REMOVAL, AIR......................24-15
OUTLETS - INSTALLATION, AIR.........24-32
OUTLETS - REMOVAL, AIR.............24-31
OUTPUT SHAFT BEARING -
INSTALLATION......................21-122
OUTPUT SHAFT BEARING - REMOVAL . . . 21-122
OUTPUT SHAFT SEAL - INSTALLATION . . 21-125
OUTPUT SHAFT SEAL - REMOVAL......21-125
PADS - INSTALLATION, STEPWELL
SCUFF.............................23-73
PADS - REMOVAL, STEPWELL SCUFF....23-72
PAINT CODES - SPECIFICATIONS........23-74
PAINT TOUCH-UP - DESCRIPTION.......23-74
PAINT TOUCH-UP - STANDARD
PROCEDURE........................23-75
PAN - INSTALLATION, OIL...............9-52
PAN - REMOVAL, OIL..................9-52
PANEL - INSTALLATION, BACKLITE -
BULKHEAD TRIM.....................23-81
PANEL - INSTALLATION, BULKHEAD
TRIM..............................23-69
PANEL - INSTALLATION, INSTRUMENT
. . . 8L-29
PANEL - INSTALLATION, QUARTER TRIM
. . 23-72
PANEL - INSTALLATION, TRIM
.....23-20,23-35,
23-46
PANEL - REMOVAL, BACKLITE -
BULKHEAD TRIM
.....................23-81
PANEL - REMOVAL, BULKHEAD TRIM
....23-69
PANEL - REMOVAL, INSTRUMENT
.......8L-28
PANEL - REMOVAL, QUARTER TRIM
.....23-71
PANEL - REMOVAL, TRIM
....23-19,23-35,23-46
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT
............8A-2
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT
........................8A-1
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT
.......................23-61
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT
.......................23-57
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT
.......................23-55
VAINDEX 11
Description Group-Page Description Group-Page Description Group-Page

SPEED SENSOR - INSTALLATION, REAR
WHEEL.............................5-31
SPEED SENSOR - REMOVAL, FRONT
WHEEL.............................5-30
SPEED SENSOR - REMOVAL, REAR
WHEEL.............................5-30
SPEED SENSORS - DESCRIPTION, INPUT . 21-119
SPEED SENSORS - OPERATION, INPUT . . 21-119
SPEEDOMETER - DESCRIPTION.........8J-23
SPEEDOMETER - OPERATION...........8J-23
SPEEDS - DESCRIPTION, TIRE
PRESSURE FOR HIGH..................22-6
SPLICE INFORMATION - DESCRIPTION,
CONNECTOR, GROUND..............8W-01-5
SPLICING - STANDARD PROCEDURE,
WIRE...........................8W-01-10
SPRING - DESCRIPTION................2-14
SPRING - INSTALLATION................2-8
SPRING - OPERATION..................2-14
SPRING - REMOVAL....................2-7
SPRING AND SHOCK - DIAGNOSIS AND
TESTING............................2-11
SPRING CLAMP PLATES - INSTALLATION . . . 2-8
SPRING CLAMP PLATES - REMOVAL.......2-8
SPRING SHACKLE - INSTALLATION.......2-15
SPRING SHACKLE - REMOVAL...........2-15
SPRING STOP PLATES - INSTALLATION.....2-9
SPRING STOP PLATES - REMOVAL........2-9
SPRINGS - INSTALLATION, VALVE..........9-32
SPRINGS - REMOVAL, VALVE............9-31
SQUEAK & RATTLE - STANDARD
PROCEDURE, BUZZ...................23-10
STABILIZER - INSTALLATION...........23-45
STABILIZER - REMOVAL...............23-45
STABILIZER BAR - DESCRIPTION..........2-9
STABILIZER BAR - INSTALLATION.....2-15,2-9
STABILIZER BAR - OPERATION............2-9
STABILIZER BAR - REMOVAL.........2-15,2-9
STABILIZER LINK - INSTALLATION.....2-16,2-9
STABILIZER LINK - REMOVAL........2-16,2-9
STARTER - DIESEL - TORQUE...........8F-29
STARTER MOTOR - DIAGNOSIS AND
TESTING...........................8F-29
STARTER MOTOR - DIESEL -
SPECIFICATIONS.....................8F-29
STARTER MOTOR - INSTALLATION.......8F-31
STARTER MOTOR - REMOVAL..........8F-30
STARTER MOTOR RELAY - DESCRIPTION . 8F-31
STARTER MOTOR RELAY -
INSTALLATION.......................8F-32
STARTER MOTOR RELAY - REMOVAL.....8F-31
STARTING - STANDARD PROCEDURE,
JUMP................................0-6
STARTING SYSTEM - DESCRIPTION......8F-24
STARTING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-25
STARTING SYSTEM - OPERATION........8F-24
STEERING - DESCRIPTION..............19-1
STEERING - OPERATION................19-1
STEERING COLUMN OPENING COVER -
INSTALLATION.......................23-66
STEERING COLUMN OPENING COVER -
REMOVAL..........................23-66
STEERING FLUID - DESCRIPTION,
POWER..............................0-3
STEERING PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER.......19-12
STEERING PUMP FILL AND BLEED
PROCEDURE, STANDARD PROCEDURE
- POWER...........................19-14
STEERING SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................19-2
STEERING SYSTEM - STANDARD
PROCEDURE, FLUSHING POWER........19-13
STEERING WHEEL - INSTALLATION.......19-7
STEERING WHEEL - REMOVAL...........19-7
STEP - INSTALLATION, REAR BUMPER....13-3
STEP - REMOVAL, REAR BUMPER........13-3
STEPS - INSTALLATION, FRONT BUMPER . . 13-2
STEPS - REMOVAL, FRONT BUMPER......13-2
STEPWELL SCUFF PADS - INSTALLATION
. 23-73
STEPWELL SCUFF PADS - REMOVAL
.....23-72
STOP LAMP BULB - INSTALLATION,
CENTER HIGH MOUNTED
...............8L-7
STOP LAMP BULB - REMOVAL, CENTER
HIGH MOUNTED
......................8L-7
STOP LAMP UN - INSTALLATION,
CENTER HIGH MOUNTED
...............8L-8STOP LAMP UN - REMOVAL, CENTER
HIGH MOUNTED......................8L-8
STOP PLATES - INSTALLATION, SPRING....2-9
STOP PLATES - REMOVAL, SPRING........2-9
STRIKER - INSTALLATION, LATCH.......23-18
STRIKER - INSTALLATION, REAR LATCH . . 23-41
STRIKER - REMOVAL, LATCH...........23-18
STRIKER - REMOVAL, REAR LATCH......23-41
STRUT - INSTALLATION................2-10
STRUT - REMOVAL....................2-10
SUCTION LINE - INSTALLATION.........24-66
SUCTION LINE - REMOVAL.............24-66
SUN VISOR - INSTALLATION...........23-73
SUN VISOR - REMOVAL...............23-73
SUPPLEMENTAL HEATER - DCHA -
DIAGNOSIS AND TESTING, DIESEL.......24-72
SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A.........8O-6
SUPPLEMENTAL RESTRAINT SYSTEM -
DIAGNOSIS AND TESTING..............8O-5
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE, HANDLING
NON-DEPLOYED......................8O-6
SUPPLY RESTRICTIONS - DIAGNOSIS
AND TESTING, FUEL...................14-5
SUPPORT BRACKET - INSTALLATION,
REAR VIEW MIRROR.................23-72
SURFACE - STANDARD PROCEDURE,
MEASURE CYLINDER HEAD.............9-21
SUSPENSION, SPECIAL TOOLS - FRONT . . 19-11
SUSPENSION, SPECIAL TOOLS - FRONT....2-2
SWITCH - DESCRIPTION, BLOWER
MOTOR.......................24-17,24-22
SWITCH - DESCRIPTION, DRIVER
HEATED SEAT ........................8G-2
SWITCH - DESCRIPTION, MASTER LOCK . . . 8N-2
SWITCH - DESCRIPTION, PASSENGER
HEATED SEAT ........................8G-5
SWITCH - DESCRIPTION, SEAT BELT.....8O-31
SWITCH - DESCRIPTION, WASHER
FLUID LEVEL.........................8R-7
SWITCH - DIAGNOSIS AND TESTING,
BLOWER MOTOR...............24-17,24-23
SWITCH - DIAGNOSIS AND TESTING,
DRIVER HEATED SEAT.................8G-2
SWITCH - DIAGNOSIS AND TESTING,
MASTER LOCK.......................8N-2
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER HEATED SEAT..............8G-5
SWITCH - DIAGNOSIS AND TESTING,
POWER MIRROR.....................8N-3
SWITCH - DIAGNOSIS AND TESTING,
POWER WINDOW.....................8N-5
SWITCH - INSTALLATION...............8P-3
SWITCH - INSTALLATION, BLOWER
MOTOR............................24-23
SWITCH - INSTALLATION, BRAKE LAMP . . . 8L-6
SWITCH - INSTALLATION, DOOR JAMB . . . 8L-31
SWITCH - INSTALLATION, DRIVER
HEATED SEAT ........................8G-3
SWITCH - INSTALLATION, FOG LAMP....8L-12
SWITCH - INSTALLATION, HEADLAMP
LEVELING..........................8L-17
SWITCH - INSTALLATION, HORN.........8H-1
SWITCH - INSTALLATION, MASTER LOCK . . 8N-2
SWITCH - INSTALLATION, MULTI-
FUNCTION..........................8L-20
SWITCH - INSTALLATION, PARK BRAKE . . . 8L-20
SWITCH - INSTALLATION, PASSENGER
HEATED SEAT ........................8G-5
SWITCH - INSTALLATION, POWER
MIRROR............................8N-4
SWITCH - INSTALLATION, POWER
WINDOW............................8N-6
SWITCH - OPERATION, BLOWER MOTOR . 24-17,
24-22
SWITCH - OPERATION, DRIVER HEATED
SEAT ...............................8G-2
SWITCH - OPERATION, PASSENGER
HEATED SEAT ........................8G-5
SWITCH - OPERATION, SEAT BELT
.......8O-31
SWITCH - OPERATION, WASHER FLUID
LEVEL
..............................8R-8
SWITCH - REMOVAL
...................8P-3
SWITCH - REMOVAL, BLOWER MOTOR
. . 24-17,
24-23
SWITCH - REMOVAL, BRAKE LAMP
.......8L-6SWITCH - REMOVAL, DOOR JAMB.......8L-31
SWITCH - REMOVAL, DRIVER HEATED
SEAT ...............................8G-3
SWITCH - REMOVAL, FOG LAMP........8L-11
SWITCH - REMOVAL, HEADLAMP
LEVELING..........................8L-16
SWITCH - REMOVAL, HORN.............8H-1
SWITCH - REMOVAL, MASTER LOCK......8N-2
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-19
SWITCH - REMOVAL, PARK BRAKE......8L-20
SWITCH - REMOVAL, PASSENGER
HEATED SEAT ........................8G-5
SWITCH - REMOVAL, POWER MIRROR....8N-3
SWITCH - REMOVAL, POWER WINDOW . . . 8N-6
SWITCH BEZEL - INSTALLATION,
ACCESSORY........................23-54
SWITCH BEZEL - REMOVAL, ACCESSORY . 23-54
SYMBOLS - DESCRIPTION,
INTERNATIONAL....................Intro.-2
SYMBOLS - DESCRIPTION,
INTERNATIONAL.......................0-9
TACHOMETER - DESCRIPTION..........8J-23
TACHOMETER - OPERATION............8J-24
TAIL LAMP UNIT - INSTALLATION.......8L-23
TAIL LAMP UNIT - REMOVAL...........8L-23
TAILPIPE - INSTALLATION...............11-3
TAILPIPE - REMOVAL..................11-3
TANK - DESCRIPTION, FUEL............14-12
TANK - INSTALLATION, FUEL...........14-13
TANK - REMOVAL, FUEL...............14-12
TANK MODULE - DESCRIPTION, FUEL....14-13
TANK MODULE - INSTALLATION, FUEL....14-14
TANK MODULE - REMOVAL, FUEL.......14-13
TCM ADAPTATION - STANDARD
PROCEDURE.........................8E-8
TEMP SENSOR - DESCRIPTION, ENGINE
COOLANT............................7-14
TEMP SENSOR - INSTALLATION, ENGINE
COOLANT............................7-15
TEMP SENSOR - REMOVAL, ENGINE
COOLANT............................7-14
TEMPERATURE CONTROL -
DESCRIPTION.......................24-29
TEMPERATURE CONTROL - DIAGNOSIS
AND TESTING.......................24-29
TEMPERATURE CONTROL -
INSTALLATION.......................24-29
TEMPERATURE CONTROL - OPERATION . . 24-29
TEMPERATURE CONTROL - REMOVAL....24-29
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE............................8J-15
TEMPERATURE GAUGE - OPERATION,
ENGINE............................8J-15
TEMPERATURE INDICATOR -
DESCRIPTION, AMBIENT...............8J-11
TEMPERATURE INDICATOR -
OPERATION, AMBIENT.................8J-11
TEMPERATURE SENSOR - DESCRIPTION . . 24-30
TEMPERATURE SENSOR - DESCRIPTION,
AIR OUTLET........................24-14
TEMPERATURE SENSOR - DESCRIPTION,
AMBIENT...........................24-15
TEMPERATURE SENSOR - DESCRIPTION,
EVAPORATOR
..................24-17,24-25
TEMPERATURE SENSOR - DESCRIPTION,
FUEL
..............................14-29
TEMPERATURE SENSOR - DESCRIPTION,
IN-CAR
............................24-19
TEMPERATURE SENSOR - DESCRIPTION,
INLET AIR
..........................14-29
TEMPERATURE SENSOR - DESCRIPTION,
OIL
................................9-56
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION
.....................21-140
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING
.......................24-30
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, EVAPORATOR
...........24-26
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, IN-CAR
................24-19
TEMPERATURE SENSOR - INSTALLATION
. 24-30
TEMPERATURE SENSOR -
INSTALLATION, AIR OUTLET
............24-15
TEMPERATURE SENSOR -
INSTALLATION, AMBIENT
..............24-16
TEMPERATURE SENSOR -
INSTALLATION, EVAPORATOR
......24-18,24-26
16 INDEXVA
Description Group-Page Description Group-Page Description Group-Page